BAOFENG MINI 5

Contents

BAOFENG MINI 5 Walkie Talkie User Manual

Model: MINI 5

BAOFENG MINI 5 Walkie Talkie with Bluetooth Programming and Dual PTT

Image: BAOFENG MINI 5 Walkie Talkie, highlighting Bluetooth Programming, 2200mAh Battery, Dual PTT, and Multi-Band capabilities.

1. Important Safety Information

Please read this manual carefully before using the BAOFENG MINI 5 Walkie Talkie to ensure safe operation and derive maximum performance from your device.

1.1 General Warnings

  • RF Energy Exposure and Product Safety: Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.
  • Antenna Care: Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Contact your local dealer for a replacement antenna.
  • Hand-Held Operation: For hand-held (held-to-face) operations, hold the radio 1 inch (2.5 cm) from your face to comply with FCC RF exposure requirements.
  • Body-Worn Operation: This device was evaluated for body-worn operations with the supplied belt-clip accessory. Use of third-party accessories (unless approved by the manufacturer) should be avoided as they might not comply with RF exposure guidelines.

1.2 Operating Prohibitions

  • Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not operate the product near or in any blasting area.
  • Avoid operating near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate where wireless communication equipment is completely prohibited.

1.3 Battery Charging Prohibitions

  • Do not charge or replace the battery in locations containing fuels, chemicals, or explosive materials.
  • Do not charge a wet battery; dry it with a soft, clean cloth first.
  • Do not charge a deformed, leaking, or overheated battery.
  • Do not charge with an unauthorized charger.
  • Do not charge in locations with strong radiation.
  • Avoid overcharging, as it may shorten battery life.

For more detailed safety information, please refer to the full user manual PDF: User manual (PDF)

2. Setup

2.1 Package Contents

Verify that all items are present in your package:

Item Quantity (PCS)
Radio1
Battery1
Antenna1
Lanyard1
Operation Manual1
Belt Clip1

Note: Charger and power adapter are subject to the final configuration of the dealer. The charging instructions in this manual may not be appropriate if Type-C charging method is used.

Package contents of BAOFENG MINI 5

Image: Visual representation of the BAOFENG MINI 5 package contents including radio, antenna, battery, clip, Type-C charger, and lanyard.

2.2 Attaching the Antenna

Turn the antenna clockwise until it is tight. To remove, turn it counterclockwise.

2.3 Charging the Battery

The BAOFENG MINI 5 features convenient Type-C charging. When using the terminal for the first time, a low battery warning may occur. It is recommended to turn off the radio during charging.

The battery's LEDs indicate the current state of charge:

Indicator Light Charging Status
Red light is always onCharging
Green light is always onCharging complete
Type-C Charging for BAOFENG MINI 5

Image: Illustrates Type-C fast charging with red light indicating charging and green light indicating full charge. Shows charging via power bank and car charger.

2.4 App Installation for Wireless Programming

The MINI 5 supports Bluetooth programming via a mobile application. Before programming wirelessly, you need to install the 'Ola Radio' app.

QR code for Ola Radio Android App

Scan for Android App

QR code for Ola Radio iOS App

Scan for iOS App

Image: QR codes for downloading the 'Ola Radio' app for Android and iOS, used for wireless programming.

After installing the app, enable Bluetooth and location services on your phone. Select the '5Rmini Series' model in the app, connect to the radio, and follow the prompts to establish a successful connection.

3. Operating Instructions

3.1 Product Overview

BAOFENG MINI 5 Product Diagram

Image: Detailed diagram of the BAOFENG MINI 5, labeling components such as Antenna, Flashlight, Microphone, Screen, Volume/Power Knob, Accessory Port, Clip, PTT-A/B Buttons, Type-C Charging Port, Type-C Charging Indicator Light, V/M-VFO/MR, OK/Menu Button, A/B, Search/Flashlight Button, Up/Down Button, and Numeric Keypad. Dimensions are also shown.

3.2 Basic Operations

Turning Your Radio On and Off

To turn the radio ON, turn the [Volume/Power] rotary knob clockwise. To turn it OFF, turn the [Volume/Power] rotary knob counterclockwise.

Setting the Volume

Increase volume by turning the [Volume/Power] rotary knob clockwise. Decrease volume by turning it counterclockwise. Do not hold the radio close to your ear if the volume is set to an uncomfortable level.

Locking or Unlocking Keypad

To prevent accidental changes to radio settings:

  1. Press and hold the [*] key to lock the keypad until the lock icon appears on the screen.
  2. In lock mode, you can still turn the intercom on/off, adjust volume, receive/transmit, send call tones, send emergency alerts, and listen to channels. Other functions remain locked.
  3. To unlock, press and hold the [*] key again until the lock icon disappears.

3.3 Channel and Frequency Management

Keypad Entry

You can enter radio aliases, channel aliases, numbers, etc., using the numeric keypad.

  1. To switch between input methods, press [# ↑] key.
  2. Press '1' to enter a special character (outside numeric input mode).
  3. Press '0' to enter a space (outside numeric input mode).

Select a Channel

Press the [V/M] button to toggle between VFO (Frequency) and Channel mode. Use the ▲/▼ buttons or the rotary encoder to select the desired channel. Alternatively, enter the 3-digit channel number directly using the keypad (e.g., 064 for channel 64).

Channel Memory

In Frequency and Standby mode, you can store frequencies and parameters:

  1. Press [MENU] [3] [MENU] [1] [5]. The screen will display “MEMCH”.
  2. Press [MENU] to enter the function. Use the ▲/▼ buttons to select the channel, then press [MENU] to store it. A sound tone will confirm success.
  3. Press [EXIT] to return to standby mode.

NOTE: If you want to set CTCSS tones, DCS codes, or frequency offset, do so before storing the channel. Stored channels are displayed as CH-, other channels have no CH- display.

Delete a Channel (DEL-CH)

In VFO mode and Standby mode:

  1. Press [MENU] [3] [MENU] [1] [6]. The screen will display “DELCH”.
  2. Press [MENU] to enter the function. Use the ▲/▼ buttons or rotate the encoder to select the channel to delete, then press [MENU] to confirm.
  3. Press [EXIT] to return to standby mode.

NOTE: Channel 1 cannot be deleted.

3.4 Advanced Features

Main Band/Sub Band Switch

In standby mode, press the [A/B] key to toggle between the A and B bands. The highlighted band is the main band; the darker displayed band is the sub-band.

VFO/Channel Switch

Press the [V/M] button to switch between VFO and channel display. VFO mode shows the ‘VFO’ icon, while MR mode shows the channel serial number.

Setting the VFO Frequency

Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel. You can input the VFO frequency directly with the keypad or use the ▲/▼ button or rotary encoder to adjust the VFO frequency.

Call Service (Initiate/Receive)

All radios in the group must be set to the same channel and sub-code to communicate. For optimal reception, keep the microphone 2.5 cm to 5 cm from your mouth when transmitting.

  • Initiate a call: Select a channel. Press and hold [PTT-A] to transmit on segment A (upper screen) or [PTT-B] to transmit on segment B (lower screen). The red indicator light will be on. Speak into the microphone with a normal voice tone.
  • Receive a call: After releasing the [PTT] key, the radio is in a receivable state. The green indicator light will be on when receiving a call.

Emergency Alarm

The terminal can initiate an emergency alarm to seek help. In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.

Flashlight

In standby mode, press the preset [8] key to turn the flashlight on or off.

FM Radio Function

Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1. Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. Operations:

  • Press ▲/▼ key to search for radio channels at the preset step frequency.
  • Press [# ↑] key to search for radio channels automatically (screen displays 'SEEK...').
  • Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
  • Press SK1 key [FM Radio] to exit radio mode.

Monitor

Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. Release the [Monitor] key to exit.

Frequency Search (Wireless Copy Frequency)

The MINI 5 supports one-touch frequency search. Press the pre-programmed [SEARCH] key or press and hold the key. The radio enters frequency search state (screen displays "SEARCH..."). Press [# ↑] key to switch the searching band (VHF/UHF, etc.). Once search is complete, press [MENU] to save the channel.

One Touch Search Frequency feature

Image: Illustrates the 'One Touch Search Frequency' feature, showing steps to search and save frequencies without manual programming.

Reverse Frequency Function

Short press the [*] key in relay mode to invert the receive and transmit frequencies. The screen shows an 'R' icon. This is useful in repeater channels with frequency differences.

Talk Around Function

In repeater mode, press [*] to switch between Talkaround Mode and Repeater Mode. The screen displays 'T' and 'R' icons. In Talkaround mode, the receive frequency equals the transmit frequency.

Repeater Activation Tone

Turn on the radio, press and hold the [PTT] key, then press [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.

Voice-activated transmit (VOX)

Enable VOX to transmit automatically when speaking, without pressing the PTT key. To enable:

  1. In Standby, press [MENU][2][MENU][4] to enter Vox Switch.
  2. Press [MENU][2][MENU][5] to enter Vox Level. Use ▲/▼ to select VOX level (1-9). A smaller value means higher sensitivity. The 'V' icon appears on the screen. Default is off.
  3. Press [MENU] to save. To turn off VOX, select OFF.

Dual Watch

In Dual Watch mode, the radio can receive frequencies on channel A or B. To enable:

  1. Press [MENU] [2] to enter Radio Set.
  2. Press [MENU] + ▲/▼ to select "15 Dual Watch".
  3. Press [MENU] key, then ▲/▼ to select “On”.
  4. Press [MENU] to save. The 'D' icon will appear. To disable, select "Off".

Stopwatch Function

Press and hold the [MENU] key to enable the stopwatch. Press [MENU] to start, [MENU] again to stop, and [EXIT] to exit.

Weather Radio/Scan Weather Channel (NOAA)

Your radio has NOAA Weather Radio functionality to receive weather reports and scan 10 NOAA channels.

  1. To turn on NOAA Weather Scan, press and hold the [0] key for 3 seconds. The NOAA icon appears, and the radio enters Weather band mode.
  2. Press and hold [# ↑] key for 3 seconds to start automatic scanning of all 10 channels. Press again to stop scan.
  3. After stopping scan, you can manually select weather channels using ▲ or ▼ keys.
  4. To exit Weather Radio broadcast mode, press the key or [PTT] key.
10 Weather Receiving Channels (NOAA)

Image: Illustrates the 10 Weather Receiving Channels feature, showing icons for various weather conditions like thunderstorm, earthquake, rainstorm, hurricane, snowstorm, and flood, emphasizing safety.

Weather Channel Frequencies:

Channel Number RX Frequency MHz Channel Number RX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

NOTE: Weather Channels Wx 1 Thru 10 are receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

3.5 Menu Functions

Basic Use of Menu

  1. Press the [MENU] button to enter the menu.
  2. Use the ▲/▼ buttons or the encoder to navigate.
  3. Press [MENU] again to select a menu item.
  4. Use the ▲/▼ buttons or the encoder to select the desired parameter.
  5. To confirm, press [MENU] (saves setting and returns to main menu). To cancel, press [EXIT] (resets item and exits menu).
  6. To exit the menu at any time, press [EXIT].

Using Menu with Shortcuts

  1. Press the [MENU] button to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. Press [MENU] to enter the menu item.
  4. For parameters, use arrow buttons or numerical keypad for short-cut code.
  5. Confirm with [MENU] or cancel with [EXIT].
  6. Exit menu with [EXIT].

Wireless Program Radio (via App)

You can program the radio wirelessly using the 'Ola Radio' app.

  1. Press [MENU] + [4] to enter Wireless CPS.
  2. Press [MENU] + ▲/▼ to select "On". The Bluetooth icon will be displayed.
  3. In the app, select '5Rmini Series', connect the radio, and click 'Walkie-talkie' to program.

Programming Steps in App:

  • Read the radio data: After reading frequency, click 'program' to enter details. Program channel info, frequency mode, optional functions.
  • Save Profile: Save the programmed profile as a new profile.
  • Write data to radio: Click 'home page', select 'program', click 'Write' to transfer frequency. The radio will restart after writing.

3.6 Shortcut Menu Operations Table

This table provides an overview of the shortcut menu options and their functions.

Menu Name Setting Description
SCANFreq RangerNNNNnnnInput VFO range lower and upper frequency
Scan ModeTimeTime Operation - scanning resumes after fixed time
CarrierCarrier Operation - scanning resumes after signal disappears
SearchSearch Operation - scanning will not resume
Radio SettingScan MemoryALLRX_TX are saved (default is all, encoding and decoding are the same)
Step2.5-100KSelects frequency change in VFO/Frequency mode
SquelchOFF, LEVEL1-LEVEL5Silences receiver when no signal. 0 opens squelch entirely.
Power SaveOFF/ONOFF: high battery consumption. ON: more power efficient.
VOX SwitchOFF/ONOFF: turn off VOX. ON: turn on VOX.
VOX LevelLEVEL1-LEVEL9Adjust gain level for smooth transmission when VOX is enabled.
VOX Delay0.5-2.0sExtends transmission time to avoid stopping too early.
TOT (Time-Out Timer)15;30;45...180Maximum allowed transmission time.
TOAOFF/1-10OFF: Disable TOA. ON: Activate TOA (0-10 seconds).
VoiceOFF/ONOFF: Disable voice prompts. ON: Activate voice prompts.
LanguageChinese/EnglishDisplay menus and voice prompts in selected language.
ROGEROFF/BEEP/TONE 1200OFF: Disable ROGER. BEEP: Sends end-of-transmission tone. TONE 1200: Sends DMC1200 end tone.
BeepOFF/ONOFF: Disable key confirmation tone. ON: Allows audible confirmation.
BackLightALWAYS ON/5-20ALWAYS ON: Backlight always on. 5-20: Set backlight off time in no-operation delay.
Power onPICTUREShow preset picture when radio is on.
Dual WatchOFF/ONOFF: Disable dual watch. ON: Monitor A and B simultaneously.
AutoLockOFF/ONOFF: Disable auto keypad lock. ON: Keypad locks if unused for 8 seconds.
Alarm ModeOn Site/Send Sound/Send CodeOn Site: Alarm through speaker. Send Sound: Transmits cycling tone. Send Code: Transmits '119' (911 reverse) + ANI code.
Alarm ToneOFF/ONOFF: Speaker blocks alarm sound. ON: Speaker sounds alarm.
ANI-Edit100View/change ANI ID.
Display ANIOFF/ONOFF: Disable ANI display. ON: Enable ANI display.
DTMF-STOFF/DT-ST/ANI-ST/DT+ANIOFF: No DTMF Side Tones. DT-ST: Heard only from manually keyed. ANI-ST: Heard only from auto keyed. DT+ANI: All DTMF Side Tones heard.
PTT-IDOFF/BOT/EOT/BOTHOFF: No ID sent. BOT: S-CODE sent at beginning. EOT: S-CODE sent at ending. BOTH: S-CODE sent at beginning and ending.
Program ChannelCH.NAMEChannel 1View/rename current channel. Use #z to switch input method.
RX FrequencyView current channel Receiver frequency.
TX FrequencyView current channel Transmitter frequency.
Trans PowerHigh/LowSelects HIGH/LOW transmitter power in VFO/Frequency mode.
Wireless CPSOFF/ONOFF: Disable Wireless CPS. ON: Enable Wireless CPS.
Radio InfoRadio ID\Firmware\HardwareDisplays radio ID, firmware version, hardware version.

4. Maintenance

4.1 General Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care.

  • Do not attempt to open the radio. Precision mechanics and electronics require specialized equipment. Unauthorized opening voids the warranty.
  • Do not store the radio under direct sunlight or in hot areas, as high temperatures can shorten device life and warp plastics.
  • Avoid storing the radio in dusty and dirty areas.
  • Keep the radio dry. Rainwater or dampness can corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off power and remove the charger or battery.
  • Do not transmit without an antenna.

4.2 Battery Maintenance

To ensure normal battery function and prolong its life:

  • Clean accumulated dust on the charging connector regularly with a clean, dry cloth.
  • Charge the battery between 5°C and 40°C. Charging outside this range may reduce battery life or cause leakage.
  • When charging a battery attached to the product, turn off the radio to ensure a full charge.
  • Do not remove the battery or unplug the power cord during charging to ensure a smooth process.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight or other heating sources for prolonged periods.
  • Do not squeeze, penetrate, or remove the battery housing.

5. Troubleshooting

While the BAOFENG MINI 5 is designed for reliable performance, issues may occasionally arise. Here are some common troubleshooting tips:

  • Programming Errors: When programming the radio, always start by reading the factory software data. Then, rewrite this data with your desired frequencies. Errors may occur if you do not follow this sequence.
  • No Power/Not Turning On: Ensure the battery is fully charged. Check that the battery is properly seated. If charging, verify the charging indicator light is green (fully charged).
  • No Transmission/Reception: Check that the antenna is securely attached. Verify that you are on the correct channel and frequency. Ensure the PTT button is functioning correctly. Check if the keypad is locked.
  • Poor Audio Quality: Adjust the volume knob. Ensure the microphone is 2.5-5 cm from your mouth during transmission. Check for obstructions around the microphone or speaker.
  • Radio Emits Smell/Smoke: Immediately turn off the radio, disconnect it from any power source, and remove the battery. Do not attempt to use it again and contact support.
  • Keypad Unresponsive: Check if the keypad is locked. Unlock it by pressing and holding the [*] key.

If you encounter persistent issues not covered here, please refer to the comprehensive user manual PDF or contact customer support.

6. Specifications

Feature Specification
Brand NameBAOFENG
Model NumberMINI-5
Walkie Talkie TypeMINI Walkie Talkie
MaterialPlastic
Output Power (W)3w-5w
Maximum Range3km-5km
Frequency Range (RX)FM: 65-108 MHz, AM: 108-136 MHz, VHF: 136-174 MHz, UHF: 350-390 MHz, 400-520 MHz, 480-520 MHz
Frequency Range (TX)VHF: 136-174 MHz, UHF: 400-480 MHz
Battery Capacity2200mAh (Upgraded)
Battery IncludedYes
Rechargeable Battery IncludedYes
Charging TypeType-C USB
Display1.44" TFT Large Screen
Storage Channel999
Waterproof / Water-ResistantNo
Dimensions (without antenna)108mm × 52mm × 37mm
Weight (with battery pack)200g
Package Length16 cm
Package Width14 cm
Package Height5 cm
Package Weight0.356 kg
Channel Spacing25.0KHz (Wide) / 12.5KHz (Narrow)
Operation VoltageDC 7.4 V ±10%
Transmission Current≤1600mA
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive Current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna Impedance50 Ohm

NOTE: All specifications may be modified without prior notice or liability.

7. Warranty & Support

7.1 Regulatory Conformance

  • EU Regulatory Conformance: The product complies with essential requirements and relevant provisions of Directive 2014/53/EU. Applicable EU regulations (2006/66/EC, 2011/65/EU, 2012/19/EU) are regarded.
  • FCC Part15/IC Compliance: This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) it must accept any interference received. Changes or modifications not expressly approved by the responsible party could void your authority to operate the equipment.

7.2 Disclaimer

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With continuous technological development, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, or dissemination of this handbook may be made without prior written authorization.

For further assistance, please refer to the full user manual PDF: User manual (PDF)

8. User Tips

Based on user feedback, here are some tips to enhance your experience with the BAOFENG MINI 5 Walkie Talkie:

  • Great Value: Users appreciate the MINI 5 as a good, basic FM transceiver offering excellent value.
  • Ease of Use: The radio is generally considered easy to use, making it suitable for various applications.
  • Compact Size: Its small size and lightweight design (only 200g) make it highly portable and convenient for camping and outdoor activities.
Small size multifunctional BAOFENG MINI 5

Image: Shows the BAOFENG MINI 5's compact size and lightweight design (200g), emphasizing its portability.

© 2023 BAOFENG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.