Introduction
Thank you for choosing the VTOMAN V-Truck 12V/24V Jump Starter. This device is a powerful and versatile tool designed to jump start 12V and 24V vehicles, act as a portable power bank, and provide emergency lighting. Please read this manual carefully before use to ensure safe and optimal operation.
Video: A promotional video showcasing the VTOMAN V-Truck Jump Starter's versatility in various scenarios, including vehicle maintenance, outdoor adventures, and family moments, highlighting its role as a reliable power solution.
Safety Warnings
Failure to follow these instructions may result in electric shock, explosion, fire, which could result in serious injury, death, or property damage.
- Please read the instructions carefully before using this product.
- The product is used for 12V or 24V vehicle engine start. It may lead to damage or be dangerous if used for other different voltage platform machines.
- DO NOT use it if the battery clamps or battery cables are damaged.
- This product is not intended to be used as a replacement vehicle battery.
- Please ensure all vehicle's battery terminals are clean and battery clamps are connected properly before jump starting the vehicle. Dirty or corroded battery terminals may affect starting performance.
- DO NOT crank the engine for more than 3 seconds at a time. The jump start feature is designed for short-term operation only. Operating for more than 3 seconds may cause damage to the unit. Allow the jump starter to cool down for at least 2 minutes after each cranking.
- Please remove the battery clamps from the vehicle battery immediately after the engine starts successfully, otherwise it may cause damage.
- Always ensure connecting the jumper cables to the vehicle's battery terminals must be positive to positive (red clamp to battery "+") and negative to negative (black clamp to battery "-").
- NEVER allow the red and black clamps to touch each other or a common piece of metal.
- This product is not for use by children and should only be operated by adults.
- DO NOT expose the product to rain, snow, or use in damp conditions. NEVER submerge the unit in water.
- DO NOT operate the product in an explosive environment, such as flammable liquids, gases, or dust.
- DO NOT modify or disassemble the product.
- Be sure to remove all metal items (watches, necklaces, rings, etc.) before using the jump start system.
- DO NOT operate the unit if it has received a sharp blow, been dropped, or otherwise damaged in any way. It must be tested by a qualified battery technician.
- DO NOT place the product in an environment where the temperature exceeds 60°C.
- Please charge only at ambient temperatures between 0°C and 45°C.
- Please use the original charger to charge the product.
- If this unit is leaking liquid, dispose of it at a proper recycle facility immediately.
- Always wear eye protection when working with batteries. Batteries can explode and cause flying debris.
- If battery acid comes into contact with eyes, flush the affected area with running water immediately for at least 15 minutes and seek medical attention immediately.
- If battery acid comes into contact with skin, rinse immediately with water and wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek medical attention immediately.
- Always ensure someone is nearby to help you in an emergency.
- Products based on lithium batteries are disposed of at the end of their life in accordance with local regulations.
Product Layout
| No. | Component | No. | Component |
|---|---|---|---|
| 1 | Battery Clamps | 7 | Flashlight Button |
| 2 | LED Flashlight | 8 | 12V Override Button |
| 3 | Battery Level Indicator | 9 | 24V Override Button |
| 4 | Warning Light | 10 | 29V/5A DC Input Port |
| 5 | 12V Mode Indicator | 11 | USB-C Input Port |
| 6 | 24V Mode Indicator | 12 | USB-A Output Ports |
Setup and Charging
Battery Status
Press any button to illuminate the Internal Battery Level Indicator LEDs, showing the current battery capacity level.
| Battery Level Indicator | 25% LED Flashing | 1 LED solid On | 2 LEDs solid On | 3 LEDs solid On | 4 LEDs solid On |
|---|---|---|---|---|---|
| Battery Level | 0% | <25% | <50% | <75% | <100% |
During charging, indicator LEDs will flash and become solid one by one. When a level is reached, the corresponding LED will be solid, and the next level LED will flash. All four LEDs will be solid when fully charged, then turn off, indicating charging completion.
Recharging the Unit
The product has two input ports: a 29V DC input port and a USB-C input port. Note that the two input ports do not support simultaneous charging; the 29V DC input has priority.
- Fast Charge: Connect the included 29V AC adapter to the 29V DC input port.
- Slow Charge: Connect a USB-C cable to the unit's USB-C input port, then connect the other end of the USB-C cable to any powered USB power port (e.g., USB wall charger or USB car charger, not included).
Important Charging Notes:
- Charge only at ambient temperatures between 0°C and 45°C.
- Recharge the battery after each use or at least every 6 months when in storage to prolong battery life and keep the unit ready for use.
USB Power Output
This product is equipped with two USB-A output ports, ideal for charging portable electronic devices.
- Connect your device(s) to the USB output port(s) using a compatible USB charge cable.
- Press any button to turn the unit on and activate USB power.
LED Flashlight
Press the flashlight button to activate the LED flashlight. Keep pressing the button to cycle through the 3 available modes: Normal Lighting, Strobe, and SOS distress signal. Press again to turn off.
Operating the Jump Starter
Jump Starting a Vehicle
Important Considerations:
- Do not attempt to jump start an engine if the battery level is at 25% or lower.
- This product supports both 12V and 24V vehicles. Always ensure the unit is set to the correct mode (12V for 12V vehicles, 24V for 24V vehicles).
- DO NOT crank the engine for more than 3 seconds at a time. The jump start feature is for short-term operation only. Allow the jump starter to cool down for at least 2 minutes after each cranking attempt.
- Press any button to turn the unit on and check the battery level indicator. If less than 25%, recharge the unit before attempting a jump start.
- Connect the red clamp to the POS "+" terminal of the vehicle battery.
- Connect the black clamp to the NEG "-" terminal of the vehicle battery.
- Check the 12V and 24V mode LEDs and the warning light on the unit, then proceed accordingly based on the table below.
| LED Status | Description | Action |
|---|---|---|
| 12V LED or 24V LED flashing or solid On. | Good connection. | Proceed with jump start attempt. |
| RED warning light solid On. | Connection is reversed. | Reconnect the clamps connections correctly. |
| 12V and 24V LEDs flashing at same time. | Vehicle battery is low, the unit cannot identify the vehicle battery system is 12V or 24V. | OVERRIDE mode will be required. See "Using Override Mode" below. |
| No any LEDs on. | No connection detected: 1. Poor connection between clamps and battery terminals, 2. Vehicle battery voltage extremely low. | Check to ensure a clean and solid connection between clamps and battery terminals. If after checking that clamps have a good connection both LEDs are OFF, the use of OVERRIDE mode will be required. See "Using Override Mode" below. |
Using Override Mode
This product has an OVERRIDE feature which allows you to force ON the jump starter function, enabling you to boost discharged batteries as low as 0 volts.
CAUTION: USE THE OVERRIDE MODE WITH EXTREME CARE
- Both the spark-proof and reverse polarity protection features are disabled in this mode.
- Pay very close attention to the polarity of the battery before using this mode.
- DO NOT allow the positive and negative battery clamps to touch each other or connect to each other as the product will generate sparks.
- DO NOT connect a 12V vehicle if the 24V OVERRIDE mode is activated.
- DO NOT connect a 24V vehicle if the 12V OVERRIDE mode is activated.
- This mode uses very high current that can cause sparks and high heat if not used properly.
- If you are unsure whether the vehicle battery system is 12V or 24V, please seek vehicle service or professional help.
- If you are unsure about using this mode, do not attempt it and seek professional help.
- ENSURE CORRECT POLARITY (red clamp to POS "+" terminal of the battery and black clamp to the NEG "-" terminal of the battery).
- ENSURE your vehicle battery system is 12V or 24V, then press and hold the 12V or 24V Mode button for 2 seconds accordingly.
- The 12V LED or 24V LED will be solid on, indicating that OVERRIDE mode is enabled.
- Proceed with the jump start attempt within 30 seconds.
Note: The OVERRIDE mode will only be active for 30 seconds. Once 30 seconds have passed, the product will reset.
Maintenance
- Storage: To extend the service life, it is recommended to use and recharge the unit every 6 months, even if not in active use. Store in a cool, dry place.
- Cleaning: Keep battery terminals clean and free from dirt or corrosion to ensure optimal performance.
- Temperature: Avoid placing the product in environments where the temperature exceeds 60°C. Charge only at ambient temperatures between 0°C and 45°C.
- Damage: Do not operate the unit if it has received a sharp blow, been dropped, or otherwise damaged. It must be tested by a qualified battery technician.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The unit cannot be activated by pressing any buttons. | Over-discharge protection may be activated. | Recharge the unit. If it still cannot be activated after recharging, contact after-sales service. |
| The unit cannot be recharged. | 1. No power from AC adapter or USB port. 2. Faulty USB cable. | 1. Change AC adapter or plug into a different USB outlet. 2. Replace USB cable. If it still cannot charge, contact after-sales service. |
| The 12V LED flashing or solid on but it still cannot jump start the vehicle. | 1. The vehicle battery system is 24V, but the battery voltage dropped in 12V. 2. Mechanical issue with vehicle. | 1. ENSURE your vehicle battery is 24V. If yes, use 24V OVERRIDE mode. See "Using Override Mode". Seek vehicle service or professional help. |
| RED warning light flashing. | Over-temperature protection is activated. | Stop use and wait for the unit to cool down. |
| The 25%/50%/75% three LEDs flashing together when recharging the unit. | Internal battery temperature is too low, recharging is forbidden. | Move to a room temperature area and recharge after the internal battery has warmed up. |
| 25%/50% two LEDs or 50%/75% two LEDs flashing together when recharging the unit. | The AC adapter is not original and does not match the unit. | Use the original AC adapter to charge the unit. |
| 25% one LED fast flashing. | Internal battery over-discharged. | Contact after-sales service if the unit is still under warranty, or purchase a new one. |
Technical Specifications
| Specification | |
|---|---|
| Model Number | V-Truck (JS-381) |
| Dimensions | 270*189*159.7mm |
| Net Weight | 2.9kg |
| Battery Type | LiFePO4 |
| Nominal Capacity | 133.59Wh / 36400mAh |
| Peak Current | 6000A |
| Output | 2 x USB-A (5V=2.4A; 5V=1A), 12V/24V Jump Start, 3W LED Flashlight |
| Input | DC 29V=5A; USB-C (5V=2A; 9V=2A) |
| Full Charge Time | About 1.5 hours |
| Operating Temperature | -40°C ~ 60°C / -40°F ~ 140°F |
| Charging Temperature | 0°C ~ 45°C / 32°F ~ 113°F |
| Storage Temperature | -40°C ~ 60°C / -40°F ~ 140°F |
| Certification | CE, FCC, RoHS, WEEE, UL |
| Application | Home Energy |
Parts List
- V-Truck Jump Starter (Host) x1
- 145W AC Adapter x1
- USB Charging Cable x1
- User Manual x1
User Tips
- For optimal battery life, remember to recharge the unit every 6 months, even if it hasn't been used.
- If the unit doesn't automatically detect your vehicle's battery voltage (12V or 24V), especially with very low or dead batteries, you'll need to manually activate the OVERRIDE mode.
- When using the OVERRIDE mode, always double-check polarity and ensure clamps do not touch to prevent sparks.
- The fast charging feature can fully charge the unit in about 1.5 hours, making it quickly ready for use.
- The unit can jump start a 12V vehicle approximately 70 times and a 24V vehicle approximately 45 times on a full charge under normal conditions.
- The unit can charge a smartphone (like an iPhone 12) about 15 times on a full charge, depending on the phone's battery capacity.
Frequently Asked Questions (FAQ)
- Q: Can this product automatically identify 12V and 24V vehicle batteries?
- A: Yes. It works fine under normal conditions, but it cannot be identified under abnormal conditions such as low vehicle voltage or no battery. When this happens, you need to activate the OVERRIDE MODE manually. Please refer to the "Using Override Mode" section.
- Q: How many times can this product jump start the vehicle?
- A: In normal conditions, with a full charge, the unit can start about 70 times for 12V vehicles and 45 times for 24V vehicles.
- Q: How long does it take to charge this product?
- A: It needs about 1.5 hours if using the original 29V AC adapter.
- Q: How many times can this product charge a phone?
- A: It depends on the capacity of the phone battery. For example, with a full charge, the unit can charge an iPhone 12 about 15 times.
- Q: What is the lifespan of the product?
- A: It can be used for 3-5 years under normal conditions.
- Q: How long can the product be stored after being fully charged?
- A: Thanks to patented technology, a fully charged unit can be stored for 3 years without issues. However, to extend its service life, it is recommended to use and recharge it every 6 months.
Environmental Protection & Toxic Substances
Composition and amount of toxic and harmful substances in product:
| Pb | Hg | Cd | Cr(VI) | PBB | PBDE |
|---|---|---|---|---|---|
| O | O | O | O | O | O |
Note: "O" indicates that the content of all homogeneous materials' hazardous substances is below the MCV limit specified in the Standard 2002/95/EC (RoHS).
Do not dispose of this product with usual household garbage at the end of its life cycle. Hand it over at a collection point for the recycling of electrical and electronic appliances. The symbols on the product, in the instructions for use, or on the packaging will inform you about the methods for disposal.
Warranty and Support
- 18 Months Limited Warranty Service: Your product is covered by a limited warranty for 18 months from the date of purchase.
- Lifetime Technical Service: VTOMAN provides lifetime technical support for this product.
- Contact Us: For any inquiries or support, please feel free to contact us at Support@vtoman.com.
- More Information: For FAQs and more information, please visit www.VTOMAN.com.