Lishui Controller JH4AZ6029DZMN

Contents

JH4AZ6029DZMN Brushless Motor Controller User Manual

Brand: Lishui Controller

Model: JH4AZ6029DZMN

1. Introduction

This manual provides essential information for the safe and efficient use of your Lishui Controller JH4AZ6029DZMN Brushless Motor Controller. This 48V 20A Lithium-Ion Sine Wave E-Bike Speed Controller is designed for electric bicycles, offering precise and smooth motor control.

Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage to the controller or your e-bike system.

Important Notice

  • This product requires confirmation of the communication protocol. If the controller protocol does not match, it may cause error codes to appear on the display.
  • Before purchasing or installing, please verify the model number of your controller. It is highly recommended to contact customer service and send photos of your original controller's label and connectors to ensure compatibility.
  • Different controller models use different communication protocols. Replacement is possible only if the communication protocols match.
  • Typically, e-bike controllers consist of connectors for the power supply, motor Hall sensor wires, brakes, throttle grip, pedal assist sensor, bike headlight, and motor. As long as you can modify the controller connectors (assistance may be available), this controller can replace your original one.

2. Specifications

JH4AZ6029DZMN Controller Specifications
FeatureDetail
ModelJH4AZ6029DZMN
TypeBrushless DC Motor Controller
VoltageDC48V
Maximum Current20±1A
Brake LevelLow level
Low Voltage Protection39±1V
Control TypeSine Wave
Dimensions (L x W x H)94mm x 52mm x 29mm
Weight262g
Operating Temperature-10°C to 45°C (Typical for Lishui Controllers)
CertificationsEN 15194:2017, EN ISO 13849-1:2015, UL 2849, UL 2272 (General Lishui Controller Certifications)
OriginMainland China
Controller with dimensions 94mm by 52mm by 29mm
Figure 2.1: Controller Dimensions (94mm x 52mm x 29mm)
Label on the controller showing model number JH4AZ6029DZMN, Voltage DC48V, Maximum current 20±1A, Brake Low level, Low voltage protection 39±1V.
Figure 2.2: Controller Label with Model and Electrical Specifications

3. Controller Components and Connectors

The JH4AZ6029DZMN controller features various connectors for integrating with your e-bike system. Understanding each connector's function is crucial for proper installation.

E-bike controller with numbered connectors: 1. Motor Phase Wires, 2. Battery Connector, 3. Display/Throttle Connector, 4. Brake Levers, 5. Pedal Assist Sensor (PAS), 6. Headlight/Tail light.
Figure 3.1: Controller with Labeled Connectors

Refer to Figure 3.1 for a visual guide to the connectors:

  1. Motor Phase Wires: Thick black cable, typically connects to the motor's phase wires (often green, blue, yellow).
  2. Battery Connector: Yellow XT60-style connector, for connecting to the e-bike's 48V battery.
  3. Display/Throttle Connector: Round 5-pin connector, usually for connecting to the e-bike display and/or throttle.
  4. Brake Levers: Two 2-pin connectors, for connecting to the e-bike's brake levers (low-level brake signal).
  5. Pedal Assist Sensor (PAS): 3-pin connector, for connecting to the pedal assist sensor.
  6. Headlight/Tail light: 2-pin connector, for connecting to the e-bike's headlight or tail light.

4. Setup and Installation

Proper installation is critical for the safe and optimal performance of your e-bike. If you are unsure about any steps, it is recommended to seek assistance from a qualified e-bike technician.

4.1 Pre-Installation Checklist

  • Ensure your e-bike battery is fully charged and disconnected before starting installation.
  • Verify that your e-bike's motor, display, and other components are compatible with a 48V 20A sine wave controller.
  • Confirm the communication protocol of your existing system matches that of the JH4AZ6029DZMN controller.
  • Gather necessary tools (e.g., screwdrivers, wire cutters/strippers, electrical tape, zip ties).

4.2 Wiring Instructions

Refer to Figure 3.1 in the "Controller Components and Connectors" section for connector identification.

  1. Mounting: Securely mount the controller in a protected area on your e-bike, ensuring it is away from direct water exposure and has adequate ventilation.
  2. Motor Connection: Connect the thick black motor phase wires (1) from the controller to the corresponding phase wires of your e-bike motor. Ensure a secure connection.
  3. Battery Connection: Connect the yellow XT60-style battery connector (2) to your 48V e-bike battery. Double-check polarity before connecting.
  4. Display/Throttle Connection: Connect the round 5-pin connector (3) to your e-bike's display and/or throttle unit.
  5. Brake Lever Connection: Connect the two 2-pin brake lever connectors (4) to your e-bike's brake levers. These provide a low-level signal to cut motor power when brakes are applied.
  6. Pedal Assist Sensor (PAS) Connection: Connect the 3-pin PAS connector (5) to your e-bike's pedal assist sensor.
  7. Light Connection (Optional): If your e-bike has a headlight or tail light powered by the controller, connect it to the 2-pin light connector (6).
  8. Cable Management: Once all connections are made, organize and secure all cables using zip ties to prevent them from snagging or getting damaged during riding.

Warning: Incorrect wiring can cause severe damage to the controller, motor, battery, or even personal injury. Always ensure all connections are correct and secure before powering on the system.

5. Operation

The JH4AZ6029DZMN controller provides smooth and efficient power delivery for your e-bike. Here are general operating guidelines:

5.1 Powering On/Off

  • To power on your e-bike system, turn on the battery switch (if applicable) and then press the power button on your e-bike display.
  • To power off, press and hold the power button on your display, then turn off the battery switch.

5.2 Riding Modes

  • Pedal Assist (PAS): The controller will provide motor assistance based on your pedaling input, detected by the PAS sensor. The level of assistance can usually be adjusted via your e-bike display.
  • Throttle: If equipped, the throttle provides on-demand motor power, allowing you to ride without pedaling.

5.3 Braking

The controller is designed to cut motor power when the brake levers are engaged, ensuring safe stopping. The low-level brake signal ensures quick response.

5.4 Sine Wave Control

This controller utilizes sine wave technology for a quieter, smoother, and more efficient motor operation compared to traditional square wave controllers.

6. Maintenance

To ensure the longevity and reliable performance of your JH4AZ6029DZMN controller, follow these maintenance guidelines:

  • Keep Clean: Regularly clean the exterior of the controller with a dry or slightly damp cloth. Avoid using harsh chemicals or excessive moisture.
  • Check Connections: Periodically inspect all electrical connections for tightness and signs of corrosion or wear. Ensure all wires are securely fastened and not frayed.
  • Environmental Protection: Protect the controller from direct exposure to heavy rain, snow, or extreme temperatures outside its operating range (-10°C to 45°C).
  • Avoid Physical Damage: Ensure the controller is securely mounted to prevent vibrations or impacts that could damage its internal components.
  • Software Updates: If available, keep your e-bike's display and controller firmware updated. Consult your e-bike manufacturer or Lishui Controller support for information on updates.

Do not attempt to open the controller casing, as this may void your warranty and expose you to electrical hazards.

7. Troubleshooting

This section addresses common issues you might encounter with your JH4AZ6029DZMN controller. For more complex problems, please contact customer support.

7.1 Common Issues & Solutions

  • No Power to System:
    • Check if the battery is charged and properly connected.
    • Ensure the battery switch is ON.
    • Verify all power cables are securely connected to the controller.
  • Motor Not Responding / Intermittent Power:
    • Check all motor phase wires and Hall sensor connections for looseness or damage.
    • Ensure throttle and PAS connections are secure.
    • Verify brake levers are not stuck in the engaged position, which would cut motor power.
  • Error Codes on Display:
    • Error codes often indicate a specific problem (e.g., motor fault, Hall sensor error, low voltage). Consult your e-bike display manual for specific code meanings.
    • As noted in the Important Notice, incompatible communication protocols between the controller and display can cause error codes. Ensure compatibility.
  • Controller Overheating:
    • Ensure the controller is mounted in a location with adequate airflow.
    • Avoid prolonged high-power usage, especially on steep inclines, which can stress the controller.

7.2 Compatibility Issues

If you experience issues after installation, particularly error codes or non-functionality, and suspect a compatibility problem:

  • Re-confirm that the controller's communication protocol matches your e-bike's display and other components.
  • If you did not verify compatibility before purchase, contact customer service with photos of your original controller's label and connectors for guidance.

8. User Tips

  • Pre-Purchase Verification: To avoid compatibility issues and ensure a smooth setup, always send photos of your original controller's label and display screen serial number to customer service before purchasing a replacement. This allows them to identify your exact model and recommend the correct replacement.
  • Connector Modification: If your existing e-bike components have different connectors than the Lishui controller, it is often possible to modify them for compatibility. Customer service can provide assistance or guidance on this process.
  • Smooth Riding: The sine wave control offers a very smooth power delivery. Utilize this for a comfortable and efficient riding experience, especially when starting from a standstill.

9. Warranty and Support

Lishui Controller is committed to providing high-quality products and excellent customer service.

9.1 Product Documentation

For more detailed information, technical specifications, and additional guides, please refer to the official Lishui Controller Brochure. A comprehensive PDF document is available for download:

View Lishui Controller Brochure (PDF)

9.2 Contact Information

For technical support, warranty claims, or any inquiries regarding your Lishui Controller product, please contact the manufacturer directly:

  • Nanjing Lishui Electronics Research Institute Co., Ltd.
  • Address: No.9 Shuibao Road, Yongyang Town, Lishui District, Nanjing, 211200, P.R.China
  • Tel: +86-25-5720-2368 / +86-25-5720-7820
  • Fax: +86-25-5721-2368
  • Email: sales@lsdzs.com
  • Website: www.lsdzs.com

For EU-specific inquiries, you may contact:

  • Lishui Electronics Europe GmbH (EU R&D Center)
  • Address: Am Bahnhof 21, 53757 Sankt Augustin, Germany
  • Mobile: +49 15221467527
  • Tel: +49-2241-9454576
  • Fax: +49-2241-9454577
  • Email: info@lsee.eu

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.