1. Introduction
The PEAKMETER PM18C is a True RMS digital multimeter designed for accurate and reliable electrical measurements. It features a large 6000-count display and offers a wide range of functions including AC/DC voltage, resistance, capacitance, frequency, temperature, and Non-Contact Voltage (NCV) testing. This manual provides essential information for the safe and effective use of your multimeter.
2. Safety Information
Always observe safety precautions when using the multimeter to prevent electric shock or personal injury. Read all safety information before operating the device.
- Ensure the multimeter is in good working condition before use.
- Do not apply voltage or current that exceeds the maximum rated values for the specific function.
- Always connect the test leads correctly to the appropriate input jacks for the measurement being performed.
- Use caution when working with voltages above 30V AC RMS, 42V peak, or 60V DC, as these pose a shock hazard.
- Replace batteries when the low battery indicator appears to ensure accurate readings.
- Do not operate the meter if the case is open or if it appears damaged.
- Refer to the CAT III 1000V and CAT IV 600V ratings for appropriate measurement environments.
3. Setup
3.1 Unpacking
Carefully remove the product from its packaging. Avoid using excessive force that could cause the device to collide or sustain damage. Inspect the multimeter for any signs of damage. If any damage is found, contact your supplier immediately.
3.2 Battery Installation
The PM18C multimeter typically uses standard batteries (e.g., AA or 9V, specific type not provided in data, refer to the full PDF manual for exact details). To install or replace batteries:
- Ensure the multimeter is turned OFF and disconnect all test leads.
- Locate the battery compartment cover on the back of the unit.
- Use a screwdriver to open the battery compartment.
- Insert new batteries, observing the correct polarity (+ and -).
- Close the battery compartment cover and secure it with the screw.
3.3 Connecting Test Leads
The multimeter has several input jacks for test leads:
- COM Jack: Common terminal for all measurements. Always connect the black test lead here.
- VΩHz%Live°C°F Jack: For voltage, resistance, frequency, capacitance, temperature, and live wire detection. Connect the red test lead here for these functions.
- mAμA Jack: For current measurements up to 600mA (fused). Connect the red test lead here for small current measurements.
- 20A Jack: For high current measurements up to 20A (fused). Connect the red test lead here for large current measurements.
Always ensure test leads are securely plugged into the correct jacks before making any measurements.
4. Operating Instructions
The PEAKMETER PM18C offers a variety of measurement functions, selected using the central rotary dial.
4.1 Basic Measurement Steps
- Select Function: Turn the rotary dial to the desired measurement function (e.g., V~ for AC Voltage, V- for DC Voltage, Ω for Resistance).
- Connect Leads: Plug the black test lead into the COM jack and the red test lead into the appropriate input jack (VΩHz%Live°C°F, mAμA, or 20A) for your measurement.
- Connect to Circuit: Carefully connect the test probes to the circuit or component you wish to measure.
- Read Display: Observe the measurement value on the digital display.
- Disconnect: Remove the test probes from the circuit and then from the multimeter.
4.2 Specific Functions
- Voltage Measurement (AC/DC): Select V~ for AC or V- for DC. Connect leads in parallel with the circuit. The PM18C features True RMS for accurate AC measurements.
- Resistance Measurement (Ω): Select Ω. Ensure the circuit is de-energized before measuring resistance. Connect leads across the component.
- Continuity Test: Select the continuity function (often shared with resistance or diode test). The meter will beep if a continuous path is detected.
- Diode Test: Select the diode function. Connect leads across the diode to measure its forward voltage drop.
- Capacitance Measurement (C/F): Select the capacitance function. Ensure capacitors are discharged before testing. The PM18C supports large capacitance measurements up to 100000uF.
- Frequency/Duty Cycle (Hz/%): Select the Hz/% function. Connect leads to the signal source.
- Temperature Measurement (°C/°F): Select the temperature function. Use the included K-type thermocouple probe.
- Current Measurement (A/mA/μA): Select the appropriate current range (A, mA, or μA). Connect leads in series with the circuit. Be mindful of the fused inputs (MAX 20A, MAX 600mA).
- Non-Contact Voltage (NCV): Select the NCV function. Hold the top of the meter near a live AC voltage source without direct contact. The meter will indicate the presence of AC voltage.
- Live Wire Detection (LIVE): Select the LIVE function. Use the red probe to touch the suspected live wire.
- Triode Measurement (hFE): Select the hFE function to test transistors.
4.3 Auto Power Off
The PM18C is equipped with an auto power-off feature to conserve battery life. The meter will automatically turn off after a period of inactivity. To reactivate, turn the rotary dial or press a button.
5. Maintenance
5.1 Cleaning
Wipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents. Keep the input terminals free of dirt and moisture.
5.2 Fuse Replacement
The current input jacks (mAμA and 20A) are fused for protection. If the meter fails to measure current, the fuse may need replacement. Refer to the full PDF manual for specific fuse ratings and replacement procedures. Always use fuses with the specified voltage and current ratings.
5.3 Storage
If the meter is not used for an extended period, remove the batteries to prevent leakage and damage. Store the meter in a cool, dry place away from direct sunlight.
6. Troubleshooting
If the multimeter is not functioning as expected, try the following basic troubleshooting steps:
- No Display/Weak Display: Check the batteries. Replace them if they are low or depleted.
- Incorrect Readings:
- Ensure the correct function is selected on the rotary dial.
- Verify that the test leads are securely connected to the correct input jacks.
- Check the integrity of the test leads for any breaks or damage.
- Ensure the circuit or component being measured is properly connected and within the meter's range.
- No Current Measurement: Check the fuses for the current input jacks (mAμA and 20A). Replace if blown.
- Meter Does Not Respond: Turn the meter off and then on again. If the issue persists, remove and reinsert the batteries.
For more detailed troubleshooting or complex issues, please refer to the comprehensive user manual PDF or contact customer support.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | PM18C |
| Display Counts | 6000 Counts |
| True RMS | Yes |
| DC Voltage Range | 600mV / 6V / 60V / 600V / 1000V |
| AC Voltage Range | 600mV / 6V / 60V / 600V / 750V |
| DC Current Range | 600μA / 6000μA / 60mA / 600mA / 20A |
| AC Current Range | 600μA / 6000μA / 60mA / 600mA / 20A |
| Resistance Range | 600Ω / 6kΩ / 60kΩ / 600kΩ / 6MΩ / 60MΩ |
| Capacitance Range | 10nF / 100nF / 1μF / 10μF / 100μF / 1000μF / 10000μF / 100000μF |
| Frequency/Duty Cycle | Yes |
| Temperature Measurement | Yes (°C/°F) |
| Non-Contact Voltage (NCV) | Yes |
| Live Wire Detection | Yes |
| Diode Test | Yes |
| Continuity Test | Yes |
| Triode (hFE) Test | Yes |
| Auto Power Off | Yes |
| Safety Rating | CAT III 1000V, CAT IV 600V |
| Dimensions (approx.) | Length: 25cm, Width: 15cm, Height: 10cm |
| Weight (approx.) | 70g |
| Origin | Mainland China |
8. User Tips
- Double-Check Settings: Always verify that the rotary dial is set to the correct function and range before connecting the probes to a circuit.
- Probe Placement: For voltage measurements, connect probes in parallel. For current measurements, connect probes in series.
- De-energize for Resistance/Continuity: Always ensure the circuit is powered off and any capacitors are discharged before measuring resistance or continuity to prevent damage to the meter or inaccurate readings.
- Use NCV for Quick Checks: The NCV feature is excellent for quickly checking for the presence of AC voltage without needing to touch the conductors directly.
- Consult Full Manual: For detailed diagrams, specific measurement procedures, and advanced features, refer to the complete user manual PDF.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
A detailed user manual in PDF format is available for further reference. You can access it via the following link: PEAKMETER PM18C User Manual (PDF).