1. Introduction
The Botslab G980H is a high-performance 4K dashcam designed to enhance driving safety and provide comprehensive vehicle surveillance. Featuring a front 4K camera and a rear 2K camera, both powered by the Sony IMX 415 sensor with STARVIS technology, it delivers ultra-clear recordings day and night. Advanced Driver-Assistance Systems (ADAS) and a dedicated AI NPU chip offer real-time alerts for potential hazards. The dashcam also includes GPS for route tracking, G-Sensor for emergency video locking, and various parking monitoring modes (requires hardwire kit).

2. Setup
2.1 Package Contents
Before installation, please verify that all items are present in your package:

- Main unit (Front Camera) x 1
- Rear camera x 1
- Car charger x 1 (3.5M cable)
- Rear camera cable x 1 (6.5M cable)
- 64GB Micro SD Card x 1
- Electrostatic film x 2
- User manual x 1
- 3M Tape x 2
- Warning Card x 1
- Installation pry bar x 1
2.2 Installation
Follow these steps for proper installation of your dashcam:

- Front Camera Placement: Mount the main unit (front camera) on your windshield, ensuring a clear view of the road ahead. Use the provided electrostatic film and 3M tape for a secure, residue-free attachment.
- Rear Camera Placement: Mount the rear camera on your rear window. The rear camera is adjustable 360° to choose your ideal view.
- Wiring: Connect the rear camera to the main unit using the rear camera cable. Connect the car charger to the main unit and plug it into your vehicle's cigarette lighter socket for power. Route cables neatly to avoid obstruction.
2.3 Initial Power On & ADAS Calibration
After wiring is complete, the recorder will automatically power on and start recording. For optimal ADAS performance, calibration is required upon first use:
- Step 1: Adjust Recorder Position: Align the ADAS calibration vertical line (displayed on the screen) with the centerline of your vehicle.
- Step 2: Adjust Camera Angle: Adjust the camera angle to align the horizontal line (displayed on the screen) with the road horizon (the end of a flat road).
- Step 3: Fine-tune (if needed): If the shooting angle is poor after initial calibration (e.g., too much ground or sky), fine-tune the camera angle and use the up/down buttons to re-align the horizontal line with the horizon.
2.4 Connect to Phone
To manage your dashcam via the Botslab app:
- Download App: Scan the QR code provided in the physical user manual or search for "Botslab" in your app store to download the application.
- Bluetooth Pairing: Enable Bluetooth pairing mode on your phone when connecting the app for the first time.
- Wi-Fi Connection: The app will connect to the recorder's Wi-Fi automatically once Bluetooth is connected. You can also manually switch between 5G and 2.4G Wi-Fi within the app settings.
3. Operating Instructions
3.1 Recorder Home Interface
The main screen displays real-time recording and various status icons:

- Recording Status: A blinking red dot indicates normal recording. "Emergency Video" blinks when triggered. "Short Video Recording" blinks when a voice command is given.
- Status Icons (from left to right):
- WiFi: Indicates if WiFi is on/off.
- Parking Monitor: Appears when parking monitor is active, disappears when off.
- GPS: Indicates GPS positioning is in use.
- Video Quality: Shows current recording quality (e.g., 4K/2K).
- Phone Connection: Indicates if the phone app is connected.
- Time-lapse Recording: Appears when time-lapse recording is active, disappears when off.
- Audio Recording: Indicates if video recording includes audio.
- Voltage Reduction Cable: Indicates if the recorder is connected to a voltage reduction cable.
- Buttons (below screen, from left to right):
- Album: Access videos and photos.
- Settings: Access recorder settings.
- Recording Switch: Turn recording function on/off.
3.2 Recorder Settings
Access the recorder menu via the 'Settings' button to configure parameters:
Video Settings
- Video Resolution: Select between 2160P and 1080P.
- Loop Recording: Set recording duration to 1min, 3min, or 5min (default is 1min).
- Audio Recording: Toggle video audio recording on/off.
- Emergency Recording Sensitivity: Adjust sensitivity for emergency video triggering.
- Built-in Speed: Enable/disable display of speed information in recorded video.
- Video Logo Watermark: Enable/disable the Botslab logo watermark in recorded video.
Parking Monitor (Requires Hardwire Kit)
This feature requires connection to a Botslab Hardwire Kit to function when the car is off.
- Parking Monitor Sensitivity: Enable/disable and select sensitivity for parking monitor function.
- Time-lapse Recording: Enable/disable time-lapse recording and select duration (8/16/24 hours).
- Continuous Power Vehicle Protection: For vehicles with constant power from the cigarette lighter. If enabled, the dashcam enters parking monitor mode after a specified period (10 or 20 minutes) to protect the battery.
- High Temperature Protection: View details on how the system automatically shuts down to protect against excessive temperatures.
Driving Assistance (ADAS)
- Fatigue Driving Reminder: Alerts for continuous driving beyond 2, 4, 6, or 8 hours.
- Safe Driving Reminder: Provides voice prompts for dangerous driving behaviors (rapid acceleration, deceleration, sharp turns).
- Front Vehicle Start: Alerts when the vehicle in front starts moving.
- Following Distance Too Close: Alerts when the distance to the vehicle ahead is too close, posing a collision risk.
- Pedestrian Collision: Alerts for the presence of pedestrians or non-motorized vehicles ahead.
System Settings
- Speaker Volume: Adjust sound level.
- Smart Voice: Enable/disable voice command recognition for controlling the recorder.
- Screen Display: Set screensaver time and interface.
- GPS Information: View GPS positioning signal data.
- Format Storage Card: Format the storage card. Always back up important videos and photos before formatting.
- Restore Factory Settings: Restore the recorder's software system to factory default without deleting recorded video files.
3.3 Function Introduction
Emergency Video
When the recorder detects a vehicle collision, it automatically starts recording a 1-minute emergency video. These videos are saved in a separate folder, and the oldest files are automatically deleted if the storage card limit is reached, without affecting new recordings. During recording, progress is displayed at the bottom of the screen.
Parking Monitoring - Collision Detection Mode (Requires Hardwire Kit)
If the vehicle experiences a collision while parked, the recorder will automatically start recording a 1-minute video upon sensing vibration. The next time the vehicle starts, you will be notified of new parking monitoring videos.
Parking Monitoring - Time-lapse Recording Mode (Requires Hardwire Kit)
After the vehicle is turned off, the recorder automatically enters time-lapse recording mode, capturing video at one frame per second. This saves approximately 30 minutes (2160P) or 60 minutes (1080P) of content as a 1-minute video. When the vehicle starts normally, it switches back to loop recording. Time-lapse videos do not record sound and play at fast-forward speed. It is recommended to watch them on a mobile phone or computer.
ADAS Function Trigger Conditions and Notification Content
ADAS features are for informational purposes only and do not replace driver vigilance. Always obey traffic regulations and drive safely. Functionality may be limited in low visibility conditions.

- Reminder for Starting Vehicle (SNG):
Trigger: Both vehicles stationary for a few seconds, then the preceding vehicle moves.
Limitations: Requires proper ADAS calibration. May not trigger for slow movements or if the preceding vehicle is too far. Limited in backlighting or nighttime.
Notification: Prompt sound and alert image (on screen). - Close Follow Distance (HMW) Warning:
Trigger: Vehicle speed > 30 km/h, and distance to vehicle ahead is less than system's set value (10-second interval between alarms).
Limitations: Requires proper ADAS calibration. Does not operate if speed < 30 km/h or vehicle ahead is too far. Limited in backlighting or night conditions. Sensitivity can be adjusted in the app (High: 60 km/h, Medium: 70 km/h, Low: 80 km/h; default is Medium).
Notification: Prompt sound and alarm image (on screen). - Lane Departure Warning System (LDWS):
Trigger: Car unintentionally crosses a lane line while driving at or above set speed.
Limitations: Requires proper ADAS calibration and clear, continuous lane dividers. May fail due to obscured dividers (rain, fog, snow, shadows, glare, road construction), misaligned/missing dividers, or extremely wide/narrow/curved roads.
Notification: Alert sound and alarm image (on screen). - Pedestrian Collision Warning:
Trigger: Vehicle speed between 10-40 km/h, and a pedestrian or non-motor vehicle appears within ten meters.
Limitations: Requires proper ADAS calibration. Algorithm is based on visual effects; poor lighting conditions can affect accuracy.
Notification: Warning sound and alert image (on screen).
4. Media Playback and Transfer
The Botslab G980H dashcam allows for quick access and transfer of recorded footage.
- In-Device Playback: Use the 'Album' button on the dashcam to view recorded videos and photos directly on the built-in screen.
- App Playback and Transfer: Connect your smartphone to the dashcam via the Botslab app. The app supports 5.8GHz Wi-Fi for faster video transfer (up to 10M/s compared to 2.4GHz at 2M/s). You can capture, replay, download, and share all your recordings through the app.

Botslab G980H Dash Cam features and functionality overview.
5. Maintenance
5.1 Storage Card Management
- Formatting: Regularly format the SD card through the 'System Settings' menu to ensure optimal performance and prevent data corruption. Always back up any important videos or photos before formatting.
- Capacity: The dashcam supports up to 256GB external memory. A 64GB MicroSD card is included for instant use.
5.2 General Care
- Cleaning: Use a soft, dry cloth to clean the camera lenses and screen. Avoid abrasive materials or chemical cleaners.
- Temperature: The dashcam is designed to operate in temperatures from -20°C to 70°C. Avoid exposing it to extreme temperatures outside this range.
- High Temperature Protection: The device includes a high temperature protection function that automatically shuts down to prevent damage from excessive heat.
6. Troubleshooting
If you encounter issues with your Botslab G980H dashcam, consider the following:
- ADAS Functionality: If ADAS features are not working correctly, ensure the dashcam has been properly calibrated as described in Section 2.3. Poor lighting, obscured lane dividers, or extreme road conditions can also limit ADAS accuracy.
- Parking Monitor Not Working: The parking monitor features (Collision Detection Mode and Time-lapse Recording Mode) require a Botslab Hardwire Kit to be connected. Ensure the kit is correctly installed and powered.
- Video Quality Concerns: If you experience 'poor quality' recordings, check your 'Video Settings' to ensure the desired resolution (4K/2K) is selected. Also, ensure lenses are clean and free from obstructions.
- SD Card Issues: If the SD card is not recording or showing errors, try formatting it via the 'System Settings' menu (remember to back up data first). Ensure the card is a high-quality, compatible MicroSD card.
- Device Unresponsive: If the device becomes unresponsive, try restoring factory settings via the 'System Settings' menu. This will not delete recorded video files.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | Botslab |
| Model | G980H |
| Item Type | Car DVR (Portable Recorder) |
| Number Of Lenses | 2 (Front & Rear) |
| Camera Resolution | 3840x2160 (Front 4K), 2K (Rear) |
| Imaging Sensor | SONY IMX415 |
| Pixels | 800Mega |
| View Angle | 170° (Front) + 150° (Rear) |
| Aperture | F1.8 |
| Display | IPS, Built-in Screen, Touch Screen |
| Loop-Cycle Recording | Yes |
| Audio Recorded | Yes |
| NightShot Function | Yes (Sony STARVIS Sensor, WDR) |
| GPS Logger | Internal (Built-in GPS, Speed and Coordinates Recording) |
| Special Features | G-Sensor, Digital zoom, motion detection, SD/MMC card, Radar Detector, Anti Vibration, Real Time Surveillance, Wide Dynamic Range, Wi-Fi function (5.8GHz), Bluetooth, Voice Control, Parking Monitor, ADAS |
| Max External Memory | 256G (64GB MicroSD card included) |
| Power Source | Corded electric (Super Capacitor, no internal battery) |
| Working Temperature | -20°C ~ 70°C |
| APP Compatibility | IOS, Android |
| OSD Language | Chinese (Traditional), Czech, Dutch, English, French, German, Italian, Malay, Polish, Russia, Spanish, THAI, Turkish, Vietnamese |
| Certification | CE, EAC, FCC, pse, weee |
| Origin | Mainland China |
8. Warranty & Support
8.1 Warranty Information
The Botslab G980H Dashcam comes with a 2 Years Store & Official Warranty. Please retain your proof of purchase for warranty claims.
8.2 User Manual (PDF)
For a detailed PDF version of the user manual, please refer to the official document available at: Botslab G980H User Manual (PDF)
8.3 Customer Support
For technical assistance, troubleshooting, or warranty inquiries, please contact Botslab customer support through their official website or the contact information provided with your purchase.
9. User Tips
- Initial App Connection: When connecting the Botslab app for the first time, ensure Bluetooth is enabled on your phone to facilitate pairing.
- SD Card Formatting: Regularly format your SD card through the dashcam's settings to maintain optimal recording performance. Always back up any important videos or photos to your phone or computer before formatting.
- Time-lapse Video Playback: Time-lapse recordings do not include audio and are played back at fast-forward speed. For best viewing experience, it is recommended to watch these videos on a mobile phone or computer rather than directly on the dashcam screen.
- ADAS Calibration: For accurate ADAS alerts, ensure the dashcam is properly calibrated during initial setup and recalibrate if the mounting position changes.
- Parking Mode: Remember that the advanced parking monitoring features (collision detection and time-lapse recording) require the separate Botslab Hardwire Kit for continuous power when the vehicle is off.