BMX Bicycle Brake Line Set

Contents

BMX Bicycle Brake Line Set with Gyro Rotor User Manual

Model: Bicycle Brake Line Set

1. Product Overview

This kit provides a complete set of brake cables and a gyro rotor system designed for BMX bicycles, specifically compatible with 20-inch bikes. It includes all necessary components for installing a front and rear brake system with a rotator rotor, ensuring smooth and reliable braking performance.

Overview of the BMX Bicycle Brake Line Set components
Figure 1: Complete Brake Line Set Components

2. Safety Information

Always ensure proper installation and adjustment of brake components before riding. Incorrect installation can lead to brake failure and serious injury. If you are unsure about any step, consult a professional bicycle mechanic.

  • Wear appropriate safety gear when riding.
  • Regularly inspect brake cables and components for wear and damage.
  • Ensure all fasteners are tightened to the manufacturer's specifications.

3. Installation Guide

This section details the installation of the BMX brake line set, including the gyro system. The kit includes a front brake line, rear X2 cables (upper and lower), and a rotator rotor.

3.1 Components Identification

Close-up of the brake line distributor
Figure 2: Brake Line Distributor (Gyro Mechanism)
Close-up of the rotator rotor
Figure 3: Rotator Rotor
Close-up of cable ends with adjusting screws
Figure 4: Cable Ends with Adjusting Screws

3.2 Gyro System Installation Steps

Refer to the diagram below for a visual guide to installing the gyro brake system. The following steps outline the general process:

Detailed diagram for BMX gyro brake system installation
Figure 5: Gyro Brake System Installation Diagram
  1. Prepare the Handlebars: Ensure your handlebars are clean and ready for brake lever and gyro plate installation.
  2. Install Rotator Rotor: Mount the rotator rotor (Figure 3) onto the head tube of your bike. Ensure it rotates freely.
  3. Connect Brake Line Distributor: Attach the brake line distributor (Figure 2) to the appropriate location, typically near the handlebars.
  4. Route Forward Shift Lines: Connect the 'Forward shift line (long)' and 'Forward shift line (short)' from the brake lever area to the brake line distributor.
  5. Route Backward Shift Line: Connect the 'Backward shift line' from the brake line distributor to the rear brake mechanism.
  6. Install Front Brake Line: Route the 'Front brake line housing' from the front brake lever to the front brake caliper.
  7. Adjusting Screws: Utilize the 'Adjusting screw' and 'Fine adjustment screw' to fine-tune cable tension and brake responsiveness.
  8. Gaskets and Nuts: Ensure all gaskets (A gasket, D gasket) and nuts are correctly placed and tightened to secure the rotating bearings and other components. Pay attention to the recommended spacing of 37mm +/- 1mm for the rotating bearings and a minimum of 1mm (1/32") clearance.
  9. Secure Cables: Ensure all cables are properly seated and secured at their 'End of line' points.

After installation, test the brakes thoroughly before riding. Ensure both front and rear brakes engage smoothly and release completely.

4. Operating Instructions

The BMX brake line set with gyro system is designed to provide smooth and reliable braking. Proper operation involves understanding how the gyro system allows for handlebar rotation without tangling brake cables.

  • Brake Lever Operation: Squeeze the brake levers on your handlebars to engage the front and rear brakes. The gyro system allows the rear brake cable to remain untangled as the handlebars rotate.
  • Braking Force: Apply even pressure to both brake levers for controlled stopping. Practice braking in a safe environment to become familiar with the feel and responsiveness of your new brake system.
  • Gyro Functionality: The gyro system enables 360-degree handlebar rotation without twisting the rear brake cable. This is essential for BMX tricks and maneuvers. Ensure the system moves freely and without resistance.

5. Maintenance

Regular maintenance ensures the longevity and optimal performance of your brake system. The cables are constructed from durable PVC and stainless steel, offering heat resistance, antioxidant properties, and high strength.

  • Cable Inspection: Periodically check all brake cables for fraying, kinks, or corrosion. Replace damaged cables immediately.
  • Housing Inspection: Inspect the outer cable housing for cracks or damage. Damaged housing can impede cable movement.
  • Lubrication: Apply a light lubricant to the inner cables and pivot points of the brake levers and calipers to ensure smooth operation. Do not over-lubricate, as this can attract dirt.
  • Adjustment: Regularly check brake lever travel and pad contact. Adjust cable tension using the adjusting screws as needed to maintain proper braking performance.
  • Cleanliness: Keep the brake components, especially the gyro rotor and distributor, free from dirt and debris.

6. Troubleshooting

This section addresses common issues you might encounter with your brake line set.

Problem Possible Cause Solution
Brakes feel spongy or weak Loose cable tension, worn brake pads, air in hydraulic system (if applicable), contaminated pads/rims. Adjust cable tension using adjusting screws. Inspect and replace brake pads if worn. Clean brake pads and rim/rotor surfaces.
Brakes drag or rub Brake calipers misaligned, cable too tight, bent rotor/rim. Loosen cable tension slightly. Realign brake calipers. Check rotor/rim for trueness.
Gyro system binds or doesn't rotate freely Dirt/debris in gyro mechanism, incorrect cable routing, insufficient lubrication, improper spacing. Clean gyro components. Re-route cables correctly. Apply light lubricant. Verify correct spacing (37mm +/- 1mm) and minimum clearance (1mm).
Cables fraying or breaking prematurely Sharp bends in housing, poor installation, excessive wear. Ensure smooth cable routing without sharp bends. Reinstall cables carefully. Replace frayed cables immediately.

7. Specifications

Feature Detail
Materials PVC (outer shell), Stainless Steel (inner cables)
Compatibility Gyro systems, 20-inch BMX bikes
Rear Moving Line Length 127.5 cm (50.1 inches)
Front Moving Line Length 40.7 cm (16 inches)
Brake Line Pipe Length 121 cm (47.6 inches)
Package Dimensions (L x W x H) 34 cm x 30 cm x 3 cm
Package Weight 0.368 kg

8. Warranty and Support

This product comes with a 1-year quality assurance from the date of purchase. If you encounter any issues or have questions regarding the product, please contact the seller directly for assistance. They are committed to providing support and will address concerns such as refunds for product defects or non-performance within the warranty period.

9. User Tips

  • Check Compatibility: Before purchasing or installing, verify that the cable lengths and gyro system are compatible with your specific BMX bike model and 20-inch wheel size.
  • Professional Installation: While installation instructions are provided, if you are not confident in your mechanical skills, consider having the brake set installed by a professional bicycle mechanic to ensure optimal safety and performance.
  • Regular Cleaning: Keep the gyro mechanism and cables clean, especially after riding in dusty or muddy conditions, to prevent binding and maintain smooth operation.

10. Frequently Asked Questions (FAQ)

Q: What are the exact measurements of the cables included in the kit?
A: The kit includes a BMX rear moving line of 127.5 cm (50.1 inches), a BMX front moving line of 40.7 cm (16 inches), and a BMX brake line pipe of 121 cm (47.6 inches).
Q: Is this brake line set suitable for all BMX bikes?
A: This set is specifically designed for gyro systems and 20-inch BMX bikes. Please check your bike's specifications for compatibility.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.