HeltecBMS HT-RT01

Contents

HeltecBMS HT-RT01 High Precision Lithium Battery Pack Internal Resistance and Voltage Tester

User Manual

1. Product Overview

The HeltecBMS HT-RT01 is a professional, high-precision intelligent tester designed for lithium battery voltage and internal resistance measurement. It supports single cells and battery packs, delivering reliable data for battery performance evaluation, quality screening, and pack assembly.

This instrument adopts a high-performance single-crystal microcomputer chip combined with a high-resolution A/D conversion chip. It uses a precise 1.000KHz AC positive current synthesized by a phase-locked loop as the measurement signal source. The generated weak voltage drop signal is processed by a high-precision operational amplifier, and the corresponding internal resistance value is analyzed by an intelligent digital filter, then displayed on a large screen dot matrix LCD.

The HT-RT01 is ideal for battery R&D, production line testing, after-sales maintenance, and battery pack assembly. It supports various lithium-ion battery chemistries including NCM, LFP, and LTO. A key advantage is its 4-wire Kelvin clamp design, which eliminates contact resistance for ultra-accurate results.

HeltecBMS HT-RT01 Lithium Battery Voltage/Internal Resistance Tester
Figure 1: HeltecBMS HT-RT01 Lithium Battery Voltage/Internal Resistance Tester

2. Safety Information and Precautions

2.1 General Safety Guidelines

  • Always read the product manual carefully before connecting or operating the device.
  • Ensure the device is connected to a stable power supply (AC110V/AC220V).
  • Do not attempt to disassemble or modify the instrument.
  • Keep the instrument away from water and moisture.

2.2 Measurement Precautions

  • Battery Preparation: When measuring the internal resistance of a battery, ensure that the positive and negative electrodes are free from dirt or oxide layers. Rub the electrodes with fine sandpaper to expose the metallic luster for accurate readings.
  • Probe Contact: When using the test fixture or test clamp, ensure good contact with the battery terminals. Poor contact can lead to inaccurate internal resistance values.
  • Voltage Limit: The maximum input voltage for this product is 100V. Do not test battery packs exceeding 100V to prevent damage to the instrument.
  • Environmental Factors: During measurement, keep the instrument away from mobile phones or high-frequency switching power supplies to prevent interference with the measurement accuracy.
  • Dry Environment: The instrument must be used in a dry environment. Moisture can lead to inaccurate measurements.
  • Test Clip Alignment: Keep the test clips parallel during testing to reduce the influence of eddy currents and improve accuracy.

3. Package Contents

Verify that all items are present in the package:

  • HT-RT01 Tester x1
  • LCR Kelvin 4-wire clamp x1
  • Test fixture x1
  • USB data cable x1
  • Power supply cord x1
  • Manual x1
Package contents of HeltecBMS HT-RT01
Figure 2: HT-RT01 Package Contents

4. Product Features

4.1 High Precision and Stability

  • Advanced Chipset: Utilizes a Microchip Technology high-resolution 18-bit AD conversion chip for accurate measurements.
  • High Resolution: Double 5-digit display with a minimum resolution of 0.1μΩ for resistance and 0.1mV for voltage.
  • Accuracy: ±0.5% for both voltage and resistance measurements.
  • Fast Test Speed: Capable of 5 readings per second for efficient batch testing.

4.2 Wide Measurement Capabilities

  • Voltage Range: 1mV ~ ±100VDC (suitable for 1S to 27S battery packs).
  • Internal Resistance Range: 1uΩ ~ 200Ω, with 6 adjustable gears for precise detection.
  • Signal Source: AC 1KHz standard signal source for consistent IR testing.
  • Automatic Multi-unit Switching: Covers a wide range of measurement needs.
  • Automatic Polarity Judgment: Automatically detects and displays battery polarity, showing a negative voltage value if inversely connected.

4.3 User-Friendly Design

  • Dual Display: Clear LCD screen shows real-time voltage and resistance values simultaneously.
  • Language Support: Switchable between Chinese and English interface.
  • Data Port: USB interface for connecting to a computer to log and analyze data.
  • Robust Build: Compact size (190x180x80mm) and lightweight (1.1kg) for portability.

4.4 Professional Testing Probe

  • LCR Kelvin 4-Wire Clamp: Eliminates wire and contact resistance, ensuring accurate low-resistance measurements.
  • Balance System Input: Compatible with battery pack balancing systems.
Front and back view of the HT-RT01 tester
Figure 3: Product Appearance Details (Front and Back)

5. Specifications

ParameterDetails
ModelHT-RT01
Measurement ParametersAC resistance, DC resistance, DC voltage
PrecisionIR: ±0.5%; V: ±0.5%
Measuring RangeIR: 0.001mΩ - 200Ω; V: 0.001V - ±100VDC
Signal SourceAC 1KHz, current: 50mA/5mA/0.5mA (gear-dependent)
Test Pace5 times/second
CalibrationManual calibration for resistance & voltage
Power SupplyAC110V/AC220V (global compatible)
Probe TypeLCR Kelvin 4-wire clamp
LanguageChinese/English switchable
Size/Weight190*180*80mm / 1.1kg
Technical parameters table for HT-RT01
Figure 4: Technical Parameters

6. Setup Instructions

6.1 Power Connection

  1. Connect the power supply cord to the AC110V/AC220V power input on the back of the HT-RT01 tester.
  2. Plug the other end of the power cord into a suitable wall outlet.
  3. Turn on the main power switch located on the back of the unit.

6.2 Connecting Test Probes/Fixture

  1. Connect the LCR Kelvin 4-wire clamp or the precision test fixture to the red (positive) and black (negative) measurement input ports on the front panel of the tester.
  2. Ensure the connections are secure.

6.3 Computer Connection (Optional)

  1. Connect the USB data cable from the tester's data port to your computer.
  2. Software Installation: Please contact the merchant to download the necessary driver software and installation video. Install the software on your computer.
  3. Open Serial Port: After the instrument powers on, press the 'Set' key to enter the menu options. Use the 'Sel' key to navigate to the 'Serial port setting' menu (usually item 7). Press the 'Enter' key, select 'ON', and press 'Enter' again to confirm. This will open the serial port for communication.
  4. Open the installed 'Battery Tester' software on your computer. Select the correct COM port (e.g., COM1) and set the baud rate to 115200. Click 'Open Serial Port'.
Connecting the HT-RT01 tester to a computer via USB
Figure 5: Connecting to a Computer for Testing

7. Operation Guide

7.1 Basic Measurement

  1. After connecting the power and probes/fixture as described in the Setup section, press the 'O/Enter' button to turn on the device.
  2. Place the battery (or battery pack) to be tested into the precision test fixture or connect it using the 4-wire Kelvin clamp. Ensure correct polarity (red for positive, black for negative).
  3. The screen will immediately display the internal resistance and voltage values of the battery under test.
  4. The instrument automatically defaults to automatic gear selection mode, intelligently identifying the battery/battery pack. Manual adjustment is not required in this mode.
  5. If the positive and negative clips are inversely connected, the tester will automatically recognize this and display the voltage value as a negative number (e.g., -3.944V).
Video 1: HT-RT01 Basic Operation and Calibration

7.2 Language Switching

  1. Press the 'Set' key to enter the menu options.
  2. Use the 'Sel' key to navigate to the 'Language' menu.
  3. Press the 'Enter' key to access the language setting interface.
  4. Use the 'Sel' key to switch between 'Chinese' and 'English'.
  5. Press the 'Enter' key to confirm your selection.

7.3 Battery Screening (with Software)

When connected to a computer with the 'Battery Tester' software, you can set specific voltage and internal resistance values to quickly screen batteries. The software will indicate 'PASS' or 'NG' (Not Good) based on your defined criteria, allowing for efficient sorting of batteries for pack assembly.

HT-RT01 display showing language selection and PC connection
Figure 6: HT-RT01 Display with Language and PC Connection Options

7.4 Data Export

The 'Battery Tester' software allows you to export measurement data to your computer for further analysis and record-keeping.

8. Calibration

8.1 Resistance Calibration

  1. Connect a standard 20mΩ resistance to the tester.
  2. Press the 'Set' key to enter the menu options.
  3. Select the 'Calibration R' (Resistance Calibration) menu.
  4. Press the 'Enter' key to confirm and enter the calibration interface.
  5. Press the 'Vol-/Res+' key to switch the measurement gear to 20mΩ.
  6. Use the 'Set' key to adjust the value of the last digit (third digit after the decimal point) of the displayed resistance.
  7. Press 'Enter' to save the calibration.

8.2 Voltage Calibration

  1. Connect a battery with a known, accurately measured voltage (reference voltage) to the tester.
  2. Press the 'Set' key to enter the menu options.
  3. Select the 'Calibration V' (Voltage Calibration) menu.
  4. Press the 'Enter' key to confirm and enter the calibration interface.
  5. Press the 'Vol-/Res+' key to switch the measurement gear to 20V.
  6. Use the 'Sel' and 'Set' keys to adjust the value of the last digit (third digit after the decimal point) of the displayed voltage (each adjustment is 0.002V).
  7. Press the 'Vol-/Res+' key again to switch the measurement range to 100V.
  8. Use the 'Sel' and 'Set' keys to adjust the value of the second digit after the decimal point (each adjustment is 0.01V).
  9. Press 'Enter' to save the calibration.

9. Applications

The HT-RT01 tester is suitable for a wide range of applications:

  • Measuring internal resistance and voltage of various battery types: ternary lithium, lithium iron phosphate, lead acid, lithium ion, lithium polymer, alkaline, dry battery, nickel-metal hydride, nickel-cadmium, and button batteries.
  • Quickly screening and matching all kinds of batteries and detecting battery performance.
  • R&D and quality testing for manufacturers of lithium batteries, nickel batteries, polymer soft-pack lithium batteries and battery packs.
  • Quality control and maintenance testing for stores.
Examples of HT-RT01 applications including measuring LiFePO4, polymer lithium, 18650 batteries, and solar panels
Figure 7: Diverse Applications of the HT-RT01 Tester

10. Maintenance

  • Cleaning: Regularly wipe the instrument with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Storage: Store the device in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Probe Care: Keep the test probes and fixture clean and free of debris to ensure accurate contact and measurements.
  • Software Updates: Check with the merchant periodically for any available software or firmware updates.

11. Troubleshooting

  • Inaccurate Readings:
    • Check for dirt or oxide layers on battery terminals and clean them if necessary.
    • Ensure good, firm contact between the test probes/fixture and the battery terminals.
    • Verify that no mobile phones or high-frequency switching power supplies are operating near the instrument during measurement.
  • Negative Voltage Display: This indicates that the positive and negative test clips are connected in reverse polarity to the battery. Correct the connection.
  • No Display/Power:
    • Check the power cord connection and ensure it is securely plugged into both the instrument and the power outlet.
    • Verify that the main power switch on the back of the unit is in the 'ON' position.
    • Check the fuse box on the back of the unit. If the fuse is blown, replace it with a fuse of the same rating.
  • Software Connection Issues:
    • Ensure the USB cable is properly connected.
    • Verify that the correct drivers are installed for the USB serial port.
    • Confirm that the 'Serial port setting' is enabled on the HT-RT01 tester (refer to Section 6.3).
    • Select the correct COM port and baud rate (115200) in the 'Battery Tester' software.

12. User Tips

  • Battery Screening: Utilize the internal resistance measurement to screen batteries. Batteries with lower internal resistance generally offer a longer lifespan and better rate performance.
  • Battery Pack Assembly: When assembling battery packs, it is crucial to screen and match cells based on capacity, internal resistance, and voltage. The overall performance of a battery pack is limited by its weakest cell (the "barrel principle"). The HT-RT01 helps identify and match cells for optimal pack performance.
  • Regular Calibration: Perform resistance and voltage calibration periodically, especially if precise measurements are critical for your application.

13. Support and Documentation

For further detailed instructions, software downloads, or technical assistance, please refer to the official user manual PDF and contact the merchant directly.

Official User Manual (PDF): A detailed user manual in PDF format is available for download. Please refer to the merchant's support resources or the provided link for the most up-to-date version: HT-RT01 User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.