KKMOON 5-in-1 Water Quality Tester

Contents

KKMOON 5-in-1 Water Quality Tester User Manual

Professional Multi-parameter Combo Testing Meter for PH, Salinity, Thermometer, TDS, and EC

1. Product Overview

The KKMOON 5-in-1 Water Quality Tester is a professional, multi-functional digital instrument designed for quick and accurate measurement of various water parameters. Its compact size and easy operation make it suitable for a wide range of applications, from household water testing to aquaculture and laboratory use.

KKMOON 5-in-1 Water Quality Tester showing PH, TDS, EC, Salinity, and Temperature ranges
Figure 1: Overview of the 5-in-1 Water Quality Tester functions and measurement ranges.

This image displays the tester and its capabilities, including pH (0.01-14.00pH), Temperature (0.1-60.0°C / 32.0-140°F), TDS (0-1000ppm, 1000ppm-10000ppm, 10.1-200.0ppt), EC (0-10000uS/cm, 10.01-19.99ms, 20.1-400ms/CM), and Salinity (0.00-25.00%, 10.1-200.0ppt).

Key Features:

  • Easy to use with high accuracy.
  • Quick and easy installation and operation.
  • Automatic 3-point calibration for EC (1413uS, 12.88mS, and 111.8mS).
  • Automatic pH calibration with 1, 2, or 3 points (6.86, 4.00, 9.18).
  • Automatic Temperature Compensation (ATC).
  • 5-minute automatic shutdown to conserve battery life.
  • Backlight function for convenient reading in various lighting conditions.
  • Waterproof rating: IP67.

2. Setup and Battery Installation

Package Contents:

  • 1 x Water Quality Monitor Tester
  • 3 x PH Buffer Powders (4.00, 6.86, 9.18)

Battery Installation:

The tester requires 3 x LR44 1.5V 160mAh button cell batteries. These are typically included with the device.

  1. Unscrew the battery compartment cap located at the top of the tester.
  2. Insert the 3 LR44 batteries, ensuring correct polarity (+/-).
  3. Securely screw the battery compartment cap back on.
Exploded view of the 5-in-1 Water Quality Tester showing battery compartment and button functions
Figure 2: Exploded view of the tester, highlighting the battery compartment, screen display, and control buttons.

This image shows the Protective Cap, Detection Head, Screen Display, ON/OFF button, HOLD/TEMP button, and MODE/CAL button, along with the battery compartment for 3 * LR44 batteries.

3. Operating Instructions

Button Functions:

  • ON/OFF: Powers the device on or off.
  • HOLD/TEMP: Press briefly to hold the current reading on the display. Long press to switch between Celsius (°C) and Fahrenheit (°F) temperature units.
  • MODE/CAL: Press briefly to cycle through measurement modes (PH, TDS, EC, Salinity). Long press to enter calibration mode.

Taking a Measurement:

  1. Turn on the tester by pressing the ON/OFF button.
  2. Remove the protective cap from the detection head.
  3. Immerse the electrode into the solution to be tested, ensuring the liquid level is below the cap.
  4. Gently stir the solution and wait for the reading to stabilize on the display.
  5. Press the MODE/CAL button briefly to switch between PH, TDS, EC, and Salinity modes as needed.
  6. To view the temperature, the device will display it alongside the primary measurement. Use the HOLD/TEMP button to switch temperature units if desired.
  7. After use, rinse the electrode with distilled water and replace the protective cap.

Calibration:

Regular calibration ensures accurate readings. The tester supports automatic identification for both pH and EC calibration solutions.

pH 3-point calibration process with buffer solutions 4.00, 6.86, and 9.18
Figure 3: Illustration of the 3-point pH calibration process using buffer solutions.

This image demonstrates the automatic identification of pH buffer solutions at 4.00, 6.86, and 9.18 for 3-point calibration.

pH Calibration:

  1. Prepare the pH buffer solutions (4.00, 6.86, and 9.18 are recommended for 3-point calibration).
  2. Turn on the tester and immerse the electrode into the 6.86 pH buffer solution.
  3. Long press the MODE/CAL button until 'CAL' appears on the display. The tester will automatically recognize the buffer.
  4. Once calibrated to 6.86, rinse the electrode with distilled water.
  5. Repeat the process for pH 4.00 and pH 9.18 buffer solutions. The tester will automatically identify and calibrate to these points.
  6. After successful calibration, the tester will return to measurement mode.

EC Calibration:

  1. Prepare the EC buffer solutions (1413uS/cm, 12.88mS/cm, and 111.8mS/cm).
  2. Turn on the tester and immerse the electrode into the 1413uS/cm buffer solution.
  3. Long press the MODE/CAL button until 'CAL' appears. The tester will automatically recognize the buffer.
  4. Once calibrated, rinse the electrode with distilled water.
  5. Repeat for the other EC buffer solutions.

4. Maintenance

Cleaning the Electrode:

  • Always rinse the electrode with distilled water before and after each use.
  • Do not use tap water or other solutions for rinsing as they may affect accuracy.
  • If the electrode is heavily soiled, gently clean it with a soft brush and a mild detergent solution, then rinse thoroughly with distilled water.

Storage:

  • Ensure the electrode is clean and dry before replacing the protective cap.
  • Store the tester in a cool, dry place away from direct sunlight and extreme temperatures.
  • For prolonged storage, it is recommended to remove the batteries to prevent leakage.

Battery Replacement:

When the battery indicator on the display shows low power, replace the batteries as described in the 'Setup and Battery Installation' section.

5. Troubleshooting

Inaccurate Readings:

  • Calibration: Ensure the tester is properly calibrated using fresh buffer solutions.
  • Electrode Cleanliness: A dirty electrode can lead to inaccurate readings. Clean the electrode as per maintenance instructions.
  • Temperature: Ensure the sample temperature is within the operating range of the device. The device features automatic temperature compensation, but extreme temperatures can still affect accuracy.
  • Buffer Solutions: Use fresh, unexpired buffer solutions for calibration.

Display Not Working/No Power:

  • Batteries: Check if the batteries are correctly installed and have sufficient charge. Replace if necessary.
  • Auto-shutdown: The device automatically shuts down after 5 minutes of inactivity. Press ON/OFF to restart.

6. Specifications

ParameterRangeResolutionAccuracy
PH0.01-14.00pH0.01pH±0.05pH
EC0-10000uS/cm, 10.01-19.99mS/cm, 20.1-400mS/cm1uS/cm; 0.1mS/cm±2% of reading
TDS0-1000ppm, 1000ppm-10000ppm, 10.1-200.0PPT1ppm; 0.1PPT±2% of reading
Salinity0.00-25.00%0.01%0.01-5.00% (±0.1%), 5.10-25.00% (±1%)
Temperature0.1-60.0℃ / 32.0-140℉0.1℃/℉±0.5℃

General Specifications:

  • Material: ABS
  • Operating Environment: 0 to 60.0℃ (32.0-140℉); RH 100%
  • TDS Factor: 0.4 to 1.0
  • Battery: 3 * LR44, 1.5V, 160mAh (included)
  • Waterproof Rating: IP67
  • Display Size: 33*24mm
  • Item Size: 180 * 37mm / 7.1 * 1.5in
  • Item Weight: 86g / 3.0ounce

7. User Tips

Understanding Water Quality (TDS):

The Total Dissolved Solids (TDS) value indicates the total soluble content in water. A lower TDS value generally suggests fewer heavy metal ions and other dissolved substances. Understanding your water's TDS can help you assess its suitability for various uses, including drinking.

TDS value interpretation chart for drinking water
Figure 4: TDS value chart for assessing drinking water quality.

This chart provides a general guide for interpreting TDS values in drinking water, ranging from 0 (ideal, e.g., reverse osmosis water) to 500+ (maximum contamination level).

Salinity Considerations:

When measuring salinity, especially for fresh water or sea water, be aware of the typical ranges. For human consumption, the World Health Organization recommends a daily salt intake of 6g, and the body's suitable intake salinity value is around 0.900%.

Salinity measurement context for fresh and sea water
Figure 5: Contextual information regarding salinity measurements.

This image provides general information about salinity, including the body's suitable intake salinity value and WHO recommendations for daily salt intake.

8. Warranty and Support

For warranty information and technical support, please refer to the seller's policies or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.