1. Introduction
The XTOOL D7S smart diagnostic system, referred to as the “Scan Tool,” is an advanced scanning tool based on the Android operating system. It offers comprehensive functions and quickly provides accurate diagnostic information for various vehicle systems. This device supports multiple languages and is suitable for different countries and regions.
The D7S V2.0 is an upgraded version of the D7, featuring 5X faster diagnostics and wider car coverage (1996-2026). It supports DoIP & CAN FD protocols for newer vehicle models, VAG Guided Function, and PMI Programming. The device runs on Android 10.0, has a 4-core 1.5 GHz processor, a 7-inch touchscreen with 1024x600 resolution, and 64GB of internal memory. It offers over 10 hours of continuous operation and includes 3 years of free Wi-Fi software updates.
Product overview video highlighting key features and capabilities of the XTOOL D7S V2.0.
2. Safety Information
Operation Instructions for Safe Use
- Keep the device away from heat or fumes during operation.
- If the vehicle battery contains acid, ensure hands, skin, and fire sources are kept away from the battery during testing.
- Ensure adequate ventilation as vehicle exhaust gas contains harmful chemicals.
- Avoid touching hot vehicle cooling system components or exhaust manifolds when the engine is running.
- Ensure the car is securely parked with Neutral or P/N selected to prevent movement when the engine starts.
- Verify the Diagnostic Link Connector (DLC) is functioning correctly before starting tests to prevent damage to the Diagnostic Computer.
- Do not switch off power or unplug connectors during testing, as this may damage the ECU and/or Diagnostic Computer.
Cautions for Device Handling
- Avoid shaking, dropping, or dismantling the scan tool to prevent damage to internal components.
- Use only fingertips to touch the LCD screen. Hard or sharp objects can cause damage.
- Do not use excessive force.
- Do not expose the screen to strong sunlight for prolonged periods.
- Keep the scan tool away from water and moisture.
- Store and use the scan tool only within the temperature ranges specified in the Technical Specifications section.
- Keep the unit away from strong magnetic fields.
Precautions for Diagnosis
- The device operates within a voltage range of +9V to +36V DC.
- When performing special functions, follow on-screen prompts and meet test conditions (e.g., engine water temperature 80-105°C, headlights/AC off, accelerator pedal released).
- If diagnostic issues arise (e.g., unable to test, abnormal data), refer to the ECU nameplate for model-specific menu selection.
- If vehicle type or electronic control system is not found, update diagnostic software via the Updates menu or contact XTOOL technical service.
- Only use XTOOL-provided wiring harnesses designed for the device to prevent damage.
- Do not shut down the device directly during Diagnostics functions. Cancel the task and return to the main interface before shutting down.
3. Product Overview
Tablet Components

Diagram showing the front and rear views of the XTOOL D7S V2.0 tablet with labeled components.
- USB Port
- DB15 Port
- Reset Hole
- Power Button
- Microphone
- Camera
- Nameplate
- Speaker
- Tablet Holder
Key Features and Upgrades
- Operating System: Upgraded Android 10 OS for faster response and no delay.
- Processor: Quad Core 1.5Ghz CPU, 5X faster than previous models.
- Display: 7-inch 1024*600 resolution touchscreen, sharper and larger.
- Memory: 2GB RAM + 64GB internal storage for smoother performance.
- Battery: 5000mAh (3.7V) for longer continuous use (10+ hours).
- Connectivity: 2.4G/5G WiFi for solid wireless upgrade, wired connection via OBDII cable.
- Protocols: Built-in CAN FD & DOIP Protocol support for newer vehicle models (e.g., GM 2020-2026, BMW F&G chassis, Volvo 2018+, Land Rover & Jaguar 2017+).
- Camera: Built-in camera for easy capture.
- Design: Adjustable kickstand for hands-free use.
- Software Updates: 3 years of free software updates and lifetime free use of all functions.
4. Setup
Wired Connection to Vehicle
- Power On and Initial Setup:
Press and hold the Power button to turn on the tablet. Select your desired App language and proceed with activation. Follow the on-screen hints to complete the activation process.
Step 1: Power on the tablet and complete initial setup.
- Connect Main Cable to Tablet:
Connect the DB15 main cable to the tablet and securely tighten the screws.
Step 2: Connect the main diagnostic cable to the tablet.
- Connect to Vehicle DLC Port:
Plug the DB15 main cable into the vehicle's DLC port via the OBD2-16 adapter.
Step 3: Connect the OBD2-16 adapter to your vehicle's DLC port.
- Ready for Diagnosis:
Your tablet is now ready for vehicle diagnosis. For models with DoIP protocol communication, ensure the device is connected to the vehicle by wire.
Step 4: The diagnostic tool is now connected and ready.
Language Selection
The D7S V2.0 supports 22+ languages. The factory presets the language and model software in English or other languages. You can switch to other languages freely. After switching the language, you will need to re-download the model software in the corresponding language.
To change the language: Update the APP to the latest version (Diagnosis APP > Setting > APP). Language authorization is no longer required.

Screen showing available languages for the XTOOL D7S V2.0.
5. Operating Instructions
After the tablet device is properly connected to the vehicle, you can begin vehicle diagnosis.
Vehicle Selection
The scan tool offers three methods to access the smart diagnostics system:
- AUTO SCAN: Automatically reads the vehicle VIN code. Tap “AUTO SCAN” on the diagnosis system entrance. Ensure the car and device are well connected.
- MANUAL INPUT: Manually enter the 17-character VIN code for accurate test results.
- SELECT VEHICLE BY AREA: Choose a car brand by selecting the appropriate region (Europe, Asia, America, China) at the top of the screen, then select the specific vehicle model.
If your model is not recognized:
- Update all software and check if the APP is updated in [Settings].
- Click Diagnosis on the main menu, manually select the engine system to read ECU information, and confirm if the VIN can be read.
- Contact the XTOOL technical team with the VIN code to confirm model support for automatic VIN identification.
Diagnosis Functions
The D7S V2.0 supports comprehensive diagnostic functions for all car systems, including Engine, Transmission, ABS, SRS, EPB, and more. These functions include:
- Read ECU Information: Displays ECU version, software/hardware versions, production date, and part numbers.
- Read/Clear Trouble Code (DTCs): Reads current, historical, and pending diagnostic trouble codes. Allows clearing codes after issues are resolved.
- Live Data: Retrieves and displays real-time parameters (PIDs) such as oil pressure, temperature, engine speed, etc. The 8-in-1 Live Data Stream allows graphing, recording, and playback of up to 8 PIDs simultaneously. Data can be exported as a CSV file.
- Freeze Frame: Records parameters at the moment a DTC occurs, aiding in diagnosis.
- Actuation Test (Bi-Directional Control): Allows sending commands to vehicle systems/components to test their operating status (e.g., Evap Tests, Fuel Injector Test, Cycling A/C Clutch Relay, Headlamp Test, Window/Mirror operation).
- Special Functions: Provides various reset and relearning functions for most vehicle systems.
- Auto Scan: Automatically scans all available systems on the vehicle.
- Control Units: Displays a selection menu of all available control units for the test vehicle.

OE-Level All Systems Diagnostic interface showing various vehicle systems and diagnostic options.

Examples of Bidirectional Controls (Active Tests) available on the XTOOL D7S V2.0.

8-in-1 Live Data Stream graphing for detailed vehicle performance analysis.
6. Special Functions (39+ Reset Services)
The D7S V2.0 supports over 39 commonly used special reset functions, enabling quick access to various scheduled services, maintenance, and reset procedures. These functions help resolve common problems and eliminate the need for manual code resets.

Menu displaying various hot reset services available on the XTOOL D7S V2.0.
6.1. ABS Bleeding
This function is used to bleed the brake system when ABS contains air, restoring brake sensitivity. It is necessary after replacing the rear/front brake distributor pump, severe brake fluid shortage, or changing brake fluid.
Operation Guidelines:
- Read operating instructions and precautions carefully.
- Attach bleeder bottle to the left rear bleeder screw.
- Open the left rear bleeder screw.
- Click "OK" to enter the bleed procedure and continuously pump the brake pedal with steady applies every 2 seconds.
- Continue pumping until air bubbles are no longer visible, then select "OK" for the next wheel.
- Repeat for left front, right front, and right rear wheels.
- Stop pumping and close the bleeder screw.
- Click "OK" to complete.
Caution:
- The ABS pump screw needs to be unscrewed.
- Brake fluid will be under pressure; secure the bleed hose and open bleeder screws slowly.
- Some vehicles may require manual bleeding.
6.2. Oil Reset
Resets the engine oil life system after an oil change, allowing the system to calculate the next optimum oil change interval.
Operation Guidelines:
- Enter the Oil Reset menu and select the vehicle model.
- Follow on-screen instructions specific to the vehicle and press OK.
- Enter the Maintenance mileage reset menu.
- Click INPUT, enter a reasonable value for remaining oil life, and press OK.
- Confirm the new value and click OK.
- A 'Write successfully' message will confirm completion.
6.3. EPB (Electronic Parking Brake) Reset
Resets the electronic parking brake system and brake pads (retraction, release of brake pump), G-sensor, and body angle calibration. Necessary after brake pad wear, replacement of brake pads/wear sensor, shorted brake pad sensor circuit, or servo motor replacement.
Operation Guidelines:
- Enter the EPB menu and select the vehicle model.
- Follow instructions and press YES.
- Enter maintenance mode and release the handbrake, then press OK.
- Wait for 'Successful operation' message and press OK to exit.
- Enter Exit maintenance mode and wait for 'Successful operation' message.
6.4. SAS (Steering Angle Sensor) Calibration
Permanently stores the current steering wheel position as the straight-ahead position in the SAS EEPROM. Necessary after replacing the steering angle position sensor, steering mechanical parts, four-wheel alignment, or car body repair.
Operation Guidelines:
- Enter the SAS menu and select the vehicle model.
- Enter the Set steering angle sensor menu and follow instructions.
- Wait for the instruction to display and press YES.
- Follow instructions and press OK.
- Wait for the instruction to display and press OK.
- A 'Function execution is completed' message will confirm completion.
6.5. BMS Reset (Battery Management System)
Evaluates battery charge state, monitors closed-circuit current, registers battery replacement, and activates the rest state of the vehicle. Necessary after main battery replacement or to re-match the control module and motoring sensor.
Operation Guidelines:
- Enter the BMS Reset menu and select the vehicle model.
- Turn on the ignition switch.
- Press OK to continue.
- Enter battery capacity (within the given range) and press OK.
- Enter the battery manufacturer and press OK.
- Enter the 10-digit battery serial number and press OK.
6.6. Injector Coding
Writes the identification code of the fuel injector into the ECU, allowing the ECU to recognize new injectors. Necessary after ECU or injector replacement.
Operation Guidelines:
- Enter the Injector coding menu and select the chassis model.
- Enter the Fuel injection nozzle injection volume adjustment menu.
- Read the displayed note and press OK.
- Read and confirm the value stored in the cylinders.
- Enter the Change the value of cylinder menu for the replaced injector(s), enter the new 5-digit value, and press OK.
- Wait for 'Write successfully' message.
- Turn off the ignition switch.
- Wait for the message to turn on the ignition switch.
- Re-enter the Fuel injection nozzle injection volume adjustment menu to check new values.
6.7. DPF Regeneration (Diesel Particulate Filter)
Manages DPF regeneration, component replacement teach-in, and DPF teach-in after ECM replacement. Used to clear PM from the DPF filter.
Operation Guidelines:
- Enter the DPF menu and select the vehicle model.
- Enter the DPF regeneration menu.
- Read and complete the requisites listed before performing DPF regeneration, then press OK.
- Read the fuel tank level and ensure it meets requirements.
- Read the carbon deposit load.
- Choose “drive to warm up” and follow instructions, then press OK.
- Read instructions carefully and follow on-screen prompts, then press OK.
- Follow instructions and press OK. Pay attention to the Note.
- Press OK to start regeneration.
- Wait for carbon deposit value to decrease and 'Emergency regeneration has been completed' message. This can take up to 40 minutes.
- Wait 2 minutes for the particulate filter to cool down.
- Press drop out to exit the DPF function.
6.8. TPMS Reset (Tire Pressure Monitor System)
Performs learning, matching, and resetting functions for tire pressure sensors. Necessary after tire replacement, troubleshooting tire pressure problems, or loss of signal from the sensor.
Note:
- Some models may require a TPMS activation tool for sensor matching.
- After learning, you may need to drive the car for a while before the fault light turns off.
- Tire pressure imbalance can also cause the tire pressure light.
The D7S V2.0 provides menus for major automotive manufacturing regions (Korea, Japan, USA, China, Australia, Europe).
TPMS Reset Methods:
- Automatic Relearn: Install sensors, adjust to standard value, keep vehicle still for 20+ minutes, drive 30-100km/h for 15+ minutes.
- Static Relearn: Install sensors, pull parking brake, turn ignition ON/RUN (engine off), enter learning mode via instrument panel, activate sensors with TPMS Activation Tool in specific order (LF, RF, RR, LR).
- OBD Relearn: Requires a TPMS Activation Tool. Install sensors, adjust to standard value, activate sensors (LF, RF, RR, LR), connect TPMS Activation Tool to OBD port, perform OBD relearn, turn ignition ON/RUN, re-trigger sensors, power off for 25+ minutes, drive 30-100km/h for 15+ minutes.
- Copy ID Relearn: Copies ID from original sensor to new sensor. Methods involve using a TPMS Activation Tool to activate/copy/program IDs, then installing the new sensor.
Note:
- Tire pressure standards are usually found in the vehicle owner's manual, on a label near the driver's door (B-pillar), in a drawer near the driver's seat, or on the fuel tank cap.
- This Scan Tool is not a replacement for a TPMS activation tool; it only provides TPMS Reset/Relearn functions. Consult your local dealer for a professional TPMS activation tool.
6.9. ECU Coding & Online Coding
This function is used after replacing faulty actuators or specific parts to generate new codes and detect new actuators. It involves matching, relearning, calibration, or initialization of adaptive data. Follow on-screen instructions to erase original ECU memories and input adaptive data.
ECU Online Coding connects directly to OEM servers to obtain online data when code data is lost. This is compatible only with VW/Audi/Skoda/Seat. Examples include digital speedometer coding, start & stop button coding, remote window control unlocking, and ambient lighting brightness adjustment.
Customize OE-Settings (Retrofit/Modification) allows enhancing vehicle performance and personalizing car settings, such as upgrading halogen fog lamps to xenon, replacing batteries, or installing larger tires. It also supports incorporating adaptive cruise control, TPMS, and reversing radar through modification.
Note:
- ECU Coding changes preprogrammed options based on existing electronic features. Compatibility varies by vehicle.

Interface for ECU Coding and Online Coding functions.
6.10. PMI (Programmable Module Installation)
This function is generally required after an ECU module has been replaced to ensure proper operation. Compatible with Ford, Lincoln, and Mazda, it allows copying data from the original module and installing it to the new unit to complete module replacement.
Note:
- If this function does not appear after connecting to the car, verify your car is one of the supported models.

Diagram illustrating the PMI (Programmable Module Installation) process.
6.11. FCA SGW AutoAuth Access
This feature allows access to the security gateway module on 2018 and newer FCA vehicles (Fiat, Chrysler, Jeep, Dodge, etc.). The D7S V2.0 can log in to the FCA account without a bypass cable, unlocking the security gateway to perform diagnostic functions like clearing DTCs, bi-directional tests, and 39+ service functions.
Note:
- You need to have an account on the FCA Website first.
6.12. CAN FD & DOIP Protocol Support
The D7S V2.0 supports the newest CAN FD and DOIP protocols, eliminating the need for extra adapters. This allows for faster diagnostics and reduces the risk of undetected errors, accommodating more data for modern vehicles.
- CAN FD: Compatible with GM vehicles from 2020-2026 (Alpheon, Buick, Chevrolet Onix/Tracker/Suburban/Tahoe, Cadillac Escalade, DAEWOO, GMC Yukon/Yukon XL, Holden, Hummer, Pontiac, Ravon, Saturn).
- DOIP: Compatible with BMW (F&G chassis), Volvo models (2018 later), Land Rover & Jaguar models (2017 later).

Diagram showing CAN FD and DOIP protocol connections and supported vehicles.
6.13. VAG Guided Function
Specifically designed for VW, Audi, Skoda, Seat, Bently, and Man LD cars, this function provides step-by-step repair guidance. It helps prevent incorrect operations that could damage car settings and offers diagnostic steps based on vehicle fault DTCs, including module testing, functional testing, wiring diagrams, and component location maps. This makes troubleshooting and repair easier for both beginners and experienced users.

Interface demonstrating the VAG Guided Function for step-by-step diagnostics.
6.14. Key Programming / IMMO Reset Function
The IMMO service allows disabling lost vehicle keys and programming replacement key fobs. It supports programming new key fobs, reading PIN codes, checking the number of keys, generating keys, remote learning, key matching, and ALL-KEYS-LOST functions.
Key Programming Features:
- Work with EEPROM Adapter to read/write/backup IMMO data.
- Read PIN code.
- Add New Keys (Fob/Smart).
- Remote Learning.
- Key Matching.
- ALL-KEYS-LOST Functions.
Note:
- Not all cars support key programming. Please send your specific car model to XTOOL support to check compatibility before purchasing.

Illustration of the Key Programming and IMMO Reset functions.
7. Diagnostic Reports
The Diagnostic Report feature allows viewing and printing saved files, including Live Data, Trouble Codes, or pictures generated during diagnosis. You can also view records of previously tested cars.
When you finish the diagnostic process and exit the application, you will be prompted to regenerate a report. The D7S V2.0 offers a newly upgraded diagnostic report (V2.0) allowing customization with logos, attachments, and pictures for more detailed reports.
Report Features:
- Customize report with your shop logo, address, and customer information.
- Select and revise diagnostic report content and name.
- Save/share diagnostic reports via email.
- Highlight critical systems with signage for enhanced readability.
Printing Reports:
- Install a compatible printer APP on the tablet and add your printer (contact XTOOL support if needed).
- On the Android main menu, go to Settings -> Printing -> Turn printer on.
- From the Report section, choose Print PDF Report -> Print.
- Click the top-left corner of the screen, choose the added printer, and click the print button.
Note:
- The Scan tool does not provide printer driver software; you must install a third-party app.

Features of the XTOOL D7S V2.0 Diagnostic Report V2.0.
8. Maintenance
Software Update
After activating the device, update the software modules via the "Updates" screen. The device will identify all available software packages for download directly via the Internet.
Cautions:
- If you contact XTOOL Support to change the language configuration, you need to download all software packages again.
- When the subscription expires, the installed software remains available, but all updates become invalid. XTOOL is not responsible for restoring software deleted due to personal operation if the subscription expires.
- To renew your subscription, contact your local dealer or XTOOL technical support.

Information on the 3 years of free software updates for the XTOOL D7S V2.0.
Factory Reset
Restoring factory settings in the Android OS system will erase custom settings and data, restart the device, and enter factory reset mode.
To perform a factory reset: Click the Settings mode from the main home page, then click “Backup & reset”. Follow on-screen prompts to initiate the process. After resetting, you can select the language in the initial setup interface.
9. Troubleshooting
DTC Status Descriptions
| DTC Status | Description | Suggestions |
|---|---|---|
| Current/Present | Trouble codes stored in the ECU when both continuous and non-continuous (2 trip) monitors fail. MIL is commanded ON. | Clear using the Scan Tool or wait for ECU monitor to complete 40 consecutive trips without fault. |
| History/Stored | Trouble codes stored when continuous and non-continuous monitors (2nd trip) fail. Not cleared by ECU monitor. | Clear only using the Scan Tool's Clear DTC function. |
| Pending | Codes that pre-set when a fault is determined in an engine cycle. Preliminary investigation for random malfunctions. | Not severe, but should not be ignored. Can be cleared using the Scan Tool's Clear DTC function. |
| Permanent | Trouble codes stored in the ECU when continuous and non-continuous monitors fail. Set in conjunction with Current and History DTCs. | Cannot be cleared using the Scan Tool. Cleared when ECU monitor completes and passes three consecutive trips. |
| Active/static (For Volkswagen) | Fault is currently happening and needs immediate attention. | Cannot be cleared directly by the diagnostic tool; internal fault must be eliminated manually. |
| Passive/sporadic (For Volkswagen) | Fault occurred in the past. | Can be cleared by Scan Tool; user should check if the DTC reappears. |
Common Issues & Solutions
- Scanning Failure / VIN Not Recognized: If the tablet shows scanning failure during automatic scanning, or if the VIN is not recognized (e.g., car too new/old, non-17-digit VIN), contact XTOOL support immediately with your car's VIN and the device's S/N for an update.
- Language Change Issues: If you cannot update the APP automatically after changing the language, contact XTOOL technical staff to push the update to you.
10. Specifications
| Attribute | Value |
|---|---|
| Model Name | XTOOL D7S Automotive Diagnostic Tools |
| Operating System | Android 10 OS |
| Processor | Quad Core 1.5Ghz |
| Display Size | 7 inches (1024*600 Resolution Touch Screen) |
| Memory | 2GB RAM + 64GB Storage |
| Battery Capacity | 5000mAh |
| Wireless Function | No (Wired Connection) |
| Wireless Support | No |
| WiFi | 2.4G/5G |
| Connection Method | Wire Connection |
| Upgrade Method | WiFi online upgrade |
| Upgrade Period | 3 years free updates |
| Charging Method | Adapter Charging |
| CAN FD & DoIP Support | Yes (Native Support) |
| USB Interface | USB2.0 |
| External Testing Certification | CE |
| Material | Plastic |
| Item Type | Other |
| Item Weight | 2.0 kg |
| Item Dimensions (L x W x H) | 23cm x 5cm x 13cm |
| Package Weight | 2.2 kg |
| Package Dimensions (L x W x H) | 25cm x 5cm x 12cm |

Visual representation of XTOOL D7S V2.0 hardware specifications.
11. Warranty and Support
Warranty
The XTOOL D7S V2.0 comes with a 2-year warranty, ensuring a trustworthy purchase.
After-Sales Services & Technical Support
For any issues or technical support, you can contact XTOOL via:
- E-Mail: supporting@xtooltech.com
- Tel: +86 755 21670995 or +86 755 86267858 (China)
- Official Website: www.xtooltech.com
Remote Assistance
XTOOL offers remote assistance to help customers with technical issues. This involves using the TeamViewer QuickSupport program.
Steps to get Remote Assistance:
- Turn on the tablet.
- Click "Remote" in the Diagnostic application. The TeamViewer screen will display your device ID.
- Ensure the tablet is connected to the Internet.
- Your partner (or XTOOL technician) must install the full TeamViewer program on their computer.
- Provide your device ID to the technician.
- When a pop-up window appears asking to permit remote control, click "Allow".
12. User Tips
- For quick delivery and customs clearance, ensure clear communication with the seller regarding necessary information and invoicing.
- Always verify the correct version (EU or Global) is selected to avoid delivery issues.
- If you encounter any issues with automatic updates or language changes, contact XTOOL technical support for assistance.
13. Frequently Asked Questions (FAQ)
- Q: Will this work on a Nissan X-Trail 2011 T31?
- A: The XTOOL D7S V2.0 supports a wide range of car brands and models from 1996-2026. For specific compatibility with your Nissan X-Trail 2011 T31, it is recommended to contact XTOOL technical support directly with your vehicle's VIN to confirm. Functions can vary by vehicle, so checking compatibility beforehand is crucial.
14. Packing List
The XTOOL D7S V2.0 package includes the following items:

Visual representation of the XTOOL D7S V2.0 and its included accessories.
- 1 PC X D7S Main Unit
- 1 PC X Quick Start Guide
- 1 PC X DB15 to OBD2-16 Main Cable
- 1 PC X Power Charger
- 1 PC X USB3.0 Data Cable
- 1 PC X Charger UE (European Plug)
- 1 PC X Charger US (US Plug)
- 1 PC X Charger UK (UK Plug)
- 1 PC X Packing List
- 1 PC X Tool Kit
- 1 PC X Carton
Compatible Expansion Accessory (Not Included): Inspection Camera