ILIFE T20s Ultra

Contents

ILIFE T20s Ultra Robot Vacuum Cleaner User Manual

Self-Empty Robotic Vacuum Cleaner

Introduction

Thank you for purchasing the ILIFE T20s Ultra Robotic Vacuum Cleaner! This manual provides essential information to help you set up, operate, and maintain your robot vacuum cleaner for optimal performance. Please read through these instructions carefully before first use.

Safety Information

Important Safety Instructions

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Remove hazards such as power cords, small items, or loose objects from the floor before cleaning.
  • Fold carpet tassels under the rug and lift hanging curtains or tablecloths off the floor.
  • For staircases or elevated areas, test whether the robot detects edges. Use barriers if necessary.
  • Use only manufacturer-recommended accessories and original rechargeable battery and charging dock.
  • Ensure the voltage matches the specifications on the charging dock.
  • This device is for indoor home use only. Do not use outdoors or in commercial environments.
  • Do not use water to rinse the device or wipe it with a wet cloth.
  • Do not operate the robot on wet or flooded surfaces.
  • Do not use near open flames or fragile items.
  • Keep hair, fingers, and loose clothing away from moving parts and openings.
  • Do not vacuum hard, sharp, flammable, or burning objects.
  • Do not use a damaged charging dock or power cord.
  • Keep the power cord away from heat sources and do not allow the robot to run over it.
  • If the power cord is damaged, have it replaced by a qualified technician.
  • Ensure the dustbin and filter are installed correctly before use.
  • Do not operate in a room where an infant is sleeping.
  • Stop using the device if it has been dropped, damaged, exposed to water, or used outdoors. Contact customer service.
  • Not suitable for high-pile carpets or certain dark-colored carpets.

Critical Safety Warnings

  • Disconnect the product from power if not used for a long period.
  • Remove the battery before cleaning or performing maintenance.
  • Always unplug the charging adapter before maintenance.
  • Warning: Non-rechargeable batteries must not be recharged.
  • Only qualified personnel may replace the battery.
  • Use only the provided auto-empty station (Model: P500) for recharging.
  • Do not power the device via external switches or circuits controlled by utility services.
  • If the power cord is damaged, it must be replaced by the manufacturer or authorized agent.
  • Maintain at least 20 cm distance between the antenna and your body during operation.
  • Frequency bands: Bluetooth 2402-2480 MHz; Wi-Fi 2412-2472 MHz.
  • Maximum RF transmission power: Bluetooth <10 dBm (EIRP), Wi-Fi <20 dBm (EIRP).
  • Before discarding the product, power it off and remove the battery. Dispose of batteries according to local regulations.
  • Do not incinerate the product or battery even if damaged.
  • Use the product only as described in this manual. ILIFE is not responsible for loss or injury from misuse.

Laser Product Information

The vacuum cleaner contains Class 1 laser products. Please refer to the following details:

Feature Laser Model PXA2 Laser Model D3A3
Laser Radiation Invisible Invisible
Exposure Near aperture may cause burns Near aperture may cause burns
Wavelength 905nm 940nm
Output Power 1mW 6mW
Frequency Steady on Steady on
Compliance EN 50689:2021 & EN 60825-1:2014+A11:2021 EN 50689:2021 & EN 60825-1:2014+A11:2021

Network Interface

The ILIFE T20s Ultra utilizes several network interfaces for seamless operation and control:

  • Bluetooth (Bluetooth LE) Interface: Primarily used for near-field device discovery and initial connection. Your mobile phone and other smart devices can quickly find the robot via Bluetooth to establish an initial communication link, preparing it for Wi-Fi networking.
  • Wi-Fi Interface: Operates in an unconnected, configurable listening mode before network distribution. It continuously listens for Wi-Fi signals and commands from the mobile application. Once connected to a specified 2.4GHz Wi-Fi network, it supports stable connections for smart home integration.
  • P2P Interface: When powered on, the robot broadcasts its location to the local network. The mobile app obtains the device's address through the router, establishing a direct communication channel. Identity verification ensures secure remote real-time control and point-to-point transmission of cleaning data.
  • Device Broadcast Service: Continuously broadcasts device information (name, type, unique identifier) via Bluetooth, allowing nearby smart devices to quickly identify and connect to the robot through the mobile application.
  • Network Service: Facilitates initial connection via Bluetooth and subsequent Wi-Fi configuration. The router's Wi-Fi network name and password are securely transferred from the app to the device. The device then attempts to connect to the specified Wi-Fi network, providing feedback on the distribution progress to the mobile app.

What's in the Box

The ILIFE T20s Ultra package includes the following components:

ILIFE T20s Ultra Robot Vacuum and Self-Emptying Station

ILIFE T20s Ultra Robot Vacuum and Self-Emptying Station

Box contents including remote, brushes, mop pads, and manuals

Accessories (Remote Control, Batteries, Brushes, Mop Pads)

  • Robot Vacuum
  • Self-empty Station
  • Dust Bag x 5
  • Mopping Support
  • Mop Cloth x 2
  • Remote Control
  • Cleaning Brush
  • Extra Side Brush
  • User Manual (this document)
  • High Performance Filter
  • AAA Battery x2 (for remote control)

Note: Product illustrations in this manual are for reference only. Due to updates and improvements, actual products may differ slightly from illustrations.

Product Overview

Robot Components

Top view of the robot vacuum showing LiDAR sensor, recharge button, power button, and bumper. Side view of the robot vacuum showing cliff sensors, side brush, side wheels, nose wheel, battery compartment, 2-in-1 roller brush, 2-in-1 dustbin & water tank, dustbin release button, cleaning scraper, and charging pins.
  • LiDAR Sensor
  • Recharge Button
  • Power/Clean/Pause Button
  • Bumper
  • Infrared Receiver Sensor
  • Cliff Sensors
  • Side Brush
  • Side Wheels
  • Nose Wheel
  • Battery Compartment
  • 2-in-1 Roller Brush
  • 2-in-1 Dustbin & Water Tank
  • Dustbin Release Button
  • Cleaning Scraper
  • Charging Pins

Water Tank Assembly

Diagram of the water tank assembly showing high performance filter, high-efficiency filter cover, sponge filter, water inlet plug, dustbin button, and dust outlet.
  • High Performance Filter
  • High-efficiency Filter Cover
  • Sponge Filter
  • Water Inlet Plug
  • Dustbin Button
  • Dust Outlet

Note: When filled with water, the robot's ability to climb over obstacles may be slightly reduced.

Self-Empty Station Components

Diagram of the self-empty station showing top cover, charging pins, dust bag, status indicator light, lens sensor, and dust inlet.
  • Top Cover
  • Charging Pins
  • Dust Bag
  • Status Indicator Light
  • Lens Sensor
  • Dust Inlet

Technical Specifications

Specification Details
ModelT20s Ultra
Dimensions (Robot)335 x 335 x 95 mm
Battery TypeLi-ion
Charging Time< 360 minutes
Dustbin Capacity0.3 L
Water Tank Capacity0.2 L
Net Weight (Robot)3.4 kg
Station Dimensions323 x 153 x 321 mm
Rated Input (Station)220V-240V ~ 50/60 Hz
Rated Output (Station)19V = 1A
Dust Bag Capacity (Station)3.5 L
Net Weight (Station)3.7 kg
Robot Suction10,000 Pa
Base Suction20,000 Pa
Climb Threshold20 mm
WiFi Frequency2.4 GHz
Control MethodsApp, Alexa and Google Assistant
Ilife ModelT20s Ultra
Weight6-10 kg
Number of operating modes3-4
Filter TypeHEPA
LCDNo
Cleaning RoutePlanned Type
Bag Or BaglessWith Bag
Cord Length (m)WireLess
Handle MaterialOthers
Timing ReservationYes
Dust Storage TypePaper Dust Bag
InstallationRobot
Certificationce
Power (W)40w
FunctionWet and Dry
Voltage220-240V
Remote ControlYes
OriginMainland China
Warranty2 years

Note: Specifications are subject to change without notice as we continuously improve our products.

Setup

Unboxing and Initial Setup

Watch this video for a visual guide on unboxing and setting up your ILIFE T20s Ultra:

Video: Unboxing and initial component overview of the ILIFE T20s Ultra.

Self-Empty Station Installation

  1. Placement Guidelines:
    • Place the station on a hard, flat surface against a wall.
    • Ensure there are no obstacles within 1.5 meters in front and 0.5 meters on both sides.
    • Avoid placing it in areas with strong sunlight or reflective surfaces.
    • Keep it away from places where pets sleep to avoid noise disturbance.
    Diagram showing recommended clearance for the self-empty station: 1.5m in front, 0.5m on sides.

    Image: Recommended placement and clearance for the self-empty station.

  2. Power Connection: Plug in the power cable. Once powered, the station's indicator light will turn on.
  3. Dust Bag Installation:
    1. Open the top cover of the station.
    2. Install the new dust bag into the station and ensure that the dust bag handle is not pulled out.
    3. Close the cover.
    Diagram showing how to install the dust bag into the self-empty station.

    Image: Installing the 3.5L large-capacity dust bag.

Charging the Robot

  1. Proper Placement: Align the robot with the charging pins on the station. When connected properly, the robot's orange charging light will blink slowly, indicating it is charging.
  2. Charging Completes: When all indicator lights turn off, the battery is fully charged.

Tip: Recharge the robot after each use to extend battery life.

Water Tank & Mop Installation

  1. Remove the Water Tank: Press the water tank's release button and pull the tank backward to remove it.
  2. Fill the Water Tank: Open the rubber plug on the tank and fill with clean water. Use purified water to reduce limescale buildup. Reseal the plug tightly to prevent leakage.
  3. Attach the Mop Cloth: Smooth the mop cloth onto the bracket and use velcro to secure it.
  4. Start Mopping: Align the bracket with the bottom of the tank and slide it in until it clicks into place. The robot will automatically detect the mop and switch to mop mode.
Diagram showing the 2-in-1 water tank and mop cloth assembly.

Image: Vacuum and Mop Combo, showing 3 Cleaning Modes and 3 Water Level Settings.

Important Notes for Mopping:

  • Do not use the mop on carpets. For best practice, zone out carpet areas in the app while mopping.
  • Do not use hot water or cleaning agents (it may damage or clog the tank).
  • Monitor water levels during mopping; refill when low.
  • After mopping, remove the mop and wash/dry it to avoid mildew or odors.

Operating Instructions

Pre-Cleaning Notes

Follow these guidelines before each use to protect your home and maximize the robot's cleaning efficiency:

  • Remove loose items from the floor: Clear cables, clothing, or small objects that could get tangled in the wheels or brushes.
  • Fold the rug's tassel trim underneath: Prevent tangling during cleaning. Avoid using on high-pile or thick rugs (>18mm or 0.71").
  • Block off dangerous zones: For areas like fireplaces, vents, or staircases, place physical barriers or set "No-Go Zones" in the app.
  • Avoid use on floor with excessive water: Avoid vacuuming large amounts of water as it will potentially damage the robot.
  • Obstacle height limit: The robot can climb over thresholds up to 20mm (0.79").
  • Cliff sensor limitations: Although the robot includes anti-drop sensors, performance may decrease on dark carpets or reflective surfaces, or if the sensors get stained. Use physical barriers as needed.

Buttons and Indicator Lights Instruction

Robot Button Instruction

Button Operation Function
PowerPress and hold 3 secondsPower on
PowerShort pressStart/Pause cleaning
PowerPress and hold 3 secondsPower off
PowerPress and hold 25 secondsSystem reset
RechargeShort pressReturn to charging dock

Robot Indicator Lights Instruction

Light Color Status Description
SolidGreenCleaning
BlinkingGreenRecharging
The green light is on until it extinguishesGreenFully charged
BlinkingOrangeLow battery
FlashingRedAlarming
No lightOffStandby

Self-Empty Station Indicator Lights Instruction

Light Color Status Description
SolidGreenRobot fully charged
Blinking slowlyGreenThe station is powered on
BlinkingOrangeDust collection in progress
Blinking slowlyOrangeRobot charging
FlashingRedNo dust bag
No lightOffStandby/sleep mode

Remote Control Guide

Before using the remote, insert two AAA/R03 batteries. Remove the batteries if not used for a long time.

Diagram of the remote control with labeled buttons.

Image: Remote control for the ILIFE T20s Ultra.

Button Function
PowerWake the robot from sleep / Start or pause cleaning
DirectionIn standby mode: Forward, Left, Right (Not functional during running)
SuctionSwitch Suction Level by Each Press: Standard → Strong → Max → Silent → Standard
Path ModeStarts standard zigzag cleaning across the entire area
Edge ModeCleans along walls and furniture edges
Spot ModeDeeply cleans a 1.5m × 1.5m area in a spiral pattern
HomeSend the robot back to the charging dock manually

Using the ILIFE Clean App

To access all features, it's recommended to control the robot through the ILIFE Clean App. The app supports 2.4GHz or dual-band 2.4GHz/5GHz networks but does not support 5GHz-only networks.

Downloading the App

  1. Scan the QR code provided in the manual or search for "ILIFE Clean" in your app store.
  2. Register/Login with your credentials.

Wi-Fi Pairing Modes

The app offers two pairing modes: Bluetooth Pairing Mode and AP (Access Point) Pairing Mode.

Bluetooth Pairing Mode
  1. Enable Bluetooth on your phone and grant permission for the ILIFE Clean app.
  2. Return to the ILIFE Clean app; the device should appear automatically. Tap "Add".
  3. Select your 2.4GHz Wi-Fi network and enter the password.
  4. The device will start downloading and be added successfully.
AP (Access Point) Pairing Mode
  1. In the app, choose your specific robot model.
  2. Choose your 2.4GHz Wi-Fi network and enter the password.
  3. Go to your phone's Wi-Fi settings and connect to a network that starts with "SmartLife". Return to the app once connected.
  4. Wait for the app to complete the device connection process.

Map Management

Access map management by opening the ILIFE Clean app, tapping "Settings", then selecting "Manage Map".

  • Create/Switch Maps: Perfect for multi-floor homes (up to 5 maps supported).
  • Reset/Delete Maps: Delete or reset a saved map.
Screenshot of the ILIFE Clean app showing a mapped floor plan.

Image: Real-time map display on the ILIFE Clean app.

Setting No-Go and No-Mop Zones

It's recommended to complete a full-home mapping before setting restricted zones.

  • No-Go Zone: Robot avoids both vacuuming and mopping in this area.
  • No-Mop Zone: Robot vacuums but does not mop in this area.
  • Virtual Wall: Acts as an invisible barrier the robot won't cross.

To set zones: Go to "forbidden edit" in the app, tap Set Restricted Areas, draw your desired zone and select the type, then save settings.

Note: These features are for convenience and do not replace physical barriers in high-risk areas like staircases.

Scheduled Cleaning

To schedule a cleaning: Open the ILIFE Clean app, go to Scheduled Cleaning, set the desired time and recurrence (e.g., daily or weekly), choose your preferred cleaning mode, and confirm your settings.

The robot will start cleaning automatically at the scheduled time and return to the charging station after cleaning.

Selecting Cleaning Modes

  • Start/Pause Cleaning: In the App, tap the "Start/Pause" button. On the Robot, press the power button once.
  • Smart Cleaning Mode: Tap "Start" in the app. The robot will leave the station, plan a route, and return when complete.
  • Room Cleaning Mode: Select specific rooms in the app for targeted cleaning.
  • Zone Cleaning Mode: Draw a rectangular zone on the map, set size and number of passes, and the robot will clean that area.
  • Spot Cleaning Mode: For localized messes, tap the target spot on the map. The robot will deep-clean a 1.5m x 1.5m area in a spiral pattern.

Dust Collection Frequency

Adjust in the app via: "Settings" → "Dust collection" → Frequency. Options include collecting dust after each sweep, after two sweeps, etc.

Cleaning Plan Customization

  • Suction & Water Level Adjustment: In the app via "Cleaning Plan", adjust suction power (Silent / Standard / Strong / Max) and water flow (Low / Medium / High).
  • Per-Room Customization: In the app via "Cleaning Plan" → "Plan 1 / Plan 2", set specific suction, water flow, number of passes, and cleaning sequence for each room.

Do Not Disturb Mode

Ideal for nighttime or rest hours. Enable in the app: "Settings" → "Robot Settings" → Do Not Disturb.

When enabled, the robot will pause auto-charge and auto-resume cleaning, stop self-emptying automatically, and shut down voice prompts.

Voice Assistant Setup (Alexa/Google Assistant)

Before setting up, ensure the T20s Ultra is fully charged and connected to the ILIFE Clean app, you own a supported voice assistant device (e.g., Amazon Echo, Google Nest), the Alexa or Google Home app is installed on your mobile device, and you have an active account for your voice assistant.

Alexa Setup

  1. Connect your robot to the ILIFE Clean app.
  2. Open the Alexa app → Tap Skills & Games → Search SmartLife.
  3. Tap "Enable to Use".
  4. Enter your ILIFE Clean account credentials and authorize access.
  5. Tap "Authorize".
  6. Alexa will search and link your robot automatically.
Image showing Alexa and Google Assistant logos, indicating voice control support.

Image: Support Voice Control with Amazon Alexa and Google Assistant.

Maintenance

Always turn off the robot and unplug the power adapter before performing maintenance.

Component Clean Frequency Replace Frequency
Mop ClothAs neededEvery 3-6 months
DustbinWeeklyN/A
FilterN/AEvery 1-1.5 months
Side BrushWeeklyEvery 3-6 months (or if damaged)
Roller BrushWeeklyEvery 6 months
Side WheelsMonthlyN/A
Cliff SensorsMonthlyN/A
Charging ContactsMonthlyN/A
Disposable Dust BagN/AEvery 1-1.5 months (or if damaged)

Cleaning the Dustbin and Filter

  1. Press the release button to remove the 2-in-1 dustbin.
  2. Open the dustbin lid.
  3. Empty the dustbin.
  4. Remove the filters and rinse the dustbin with water.
  5. Dry thoroughly with a clean cloth.
  6. Replace the filter if necessary and reinsert the dustbin.

Note: The filter is unwashable.

Cleaning the Water Tank and Mop Cloth

Mop Cloth

  1. Remove the mop bracket and peel off the cloth.
  2. Rinse with clean water and let it air-dry completely.

2-in-1 Water Tank

  1. Open the rubber plug and drain any leftover water.
  2. Wipe the tank clean and let it dry thoroughly.

Cleaning the Roller Brush

  1. Unlock and lift the brush cover.
  2. Remove the roller brush by pulling it upward.
  3. Use the provided tool to cut away tangled hair or debris.
  4. Rinse the roller brush and cover with water.
  5. Air-dry those components.
  6. Reinstall the roller brush and snap the cover back into place.

Cleaning the Side Brushes and Side Wheels

  • Side Brushes: Unscrew and remove the brushes. Clear hair or debris wrapped around them.
  • Side Wheels: Check and remove any obstructions caught in the wheels.

Cleaning the Sensors and Charging Pins

  • Infrared Obstacle Avoidance Sensor: Wipe both the infrared obstacle avoidance sensor with a dry cloth to maintain charging efficiency.
  • Cliff Sensors: Use a soft brush to gently clean the sensors on the underside of the robot.
  • Charging Pins: Wipe both the robot's and station's charging pins with a dry cloth to maintain charging efficiency.

Replacing the Dust Bag and Cleaning the Station

Replace Dust Bag

  1. Open the top cover.
  2. Remove and dispose of the used dust bag.
  3. Install the new dust bag.

Reminder:

  • Damaged bags can impair performance and damage the station. Check regularly.
  • Check the metal filter at the inside bottom of the station in case of clogging.

Clear the Dust Path

If the suction is weakened or blocked:

  1. Unplug the station.
  2. Flip it over and unscrew the transparent duct cover.
  3. Remove debris and reinstall the cover.

Battery Care and Activation

For Long-Term Storage

  1. Charge the robot fully.
  2. Power it off (hold the power button for 3 seconds).
  3. Store in a dry, ventilated place. Recharge every 3 months to avoid battery degradation.

Battery Activation (After Deep Discharge or Long Inactivity)

  1. Align the robot on the charging station.
  2. Charge it for 3 minutes and then remove it. Repeat this process 3 times.
  3. Then charge continuously for 5-6 hours until it is fully charged when the indicator turns off.

Troubleshooting

Voice Alerts & Error Codes

When a malfunction occurs, the robot's indicator light will flash red and a voice alert will play. Use the table below to identify and resolve the issue.

Voice Alert Possible Cause Solution
Side wheel/Side brush blockedHair or debris is caughtCheck and clean side wheels/brushes
Please check the cliff sensor/Bumper is stuckBumper gets caught or stained/cliff sensors get stainedClear and clean those components
Robot is stuckTrapped by cords or obstaclesRemove the obstruction
Gyroscope initialization failedGyroscope failed to position due to robot skiddingRemove and relocate the robot

Water Tank / Mopping Issues

Issue Possible Cause Solution
Water tank leakingRubber plug not sealedReseal the plug
No water output while moppingThe water tank not installed properly or emptyReinstall or refill the tank
Mop cloth falling offVelcro not attached well or worn outSecure the mop cloth or replace it

Self-Empty Station Issues

Issue Possible Cause Solution
Station not workingDust bag not installed properly or clogging happensReinstall or replace dust bag, or refer to 6.7 to clear inside filter and dust path
Indicator light blink orange but the dust is not emptyingRobot not properly dockedAdjust position to align charging pins

App Issues

Issue Possible Cause Solution
Can't connect to the appIncorrect router username/passwordRe-enter correct Wi-Fi credentials
Out of Wi-Fi signal coverageMove the robot closer to the router
Robot not in pairing modeHold the power button for 6 seconds until "WiFi pairing" prompt is heard
Incompatible network typeOnly supports 2.4GHz or mixed 2.4/5GHz networks, not 5GHz-only
Wrong app installedUse the QR code or app store to download ILIFE Clean app
Map not generatedThe robot does not start cleaning from stationStart cleaning from charging station
Robot was moved during cleaningAvoid moving the robot in mid of cleaning
Task has not completedLet robot finish the cleaning session and return to the station automatically.

Robot Issues

Issue Possible Cause Solution
Robot returns before finishingBattery gets low in large areasEnable "Auto Resume" feature in the app
Cleaning coverage may be poor due to complex home layout.Tidy the environment for better navigation
Can't chargeCharging pins not aligned or dirtyAdjust position and clean pins
The station is not poweredEnsure the station is plugged into a power supply.
Battery over-discharged from long storageManually charge 3 times for 3 mins each, then full charge for 5-6 hours
Loud noise during operationBrushes or dustbin clogged; in high suction modeClean components or switch to standard mode
Frequently gets stuckTangled in wires/carpet fringe or get stuck under low furnitureTidy up or use virtual walls in app
Climbing ability is weakened with mop installedRemove the mop bracket, or assist robot over high thresholds if needed
Skipped or repeated cleaning areasThe floor is too clutteredTidy up the cables, shoes
The robot can not navigate correctly due to wheel skidding in failure to climb the threshold, or on a slippery floorClose doors to problematic rooms to avoid threshold, avoid waxed floors
Top LiDAR does not work due to dust or foreign objects caught on sensorClean the LiDAR with soft cloth
Can't return to the stationImproper station placement or power lossRefer to Self-Empty Station Installation for correct placement.
The robot does not start cleaning from stationSuggest to start from station
Obstructed return path (e.g., door closed)Keep the return path clear

If the issue persists:

  1. Press and hold the power button for 3 seconds to turn off, then press for 3 seconds to restart.
  2. If still unresolved, please contact customer support.

User Tips

  • The ILIFE T20s Ultra is known for its quiet operation despite powerful suction.
  • It vacuums and mops thoroughly, effectively reaching corners and performing detailed surface scans.
  • The mopping function uses water only and does not replace deep cleaning with cleaning agents.
  • The remote control allows for basic operation without needing the app, which is convenient for quick tasks.
  • The app, while relying on external services (Tuya), stores maps, schedules, and settings on the device, allowing it to function without a constant network connection once configured.
  • This robot vacuum is highly effective at picking up pet hair.
  • Regularly check and clean the brushes after each use, as hair can accumulate and affect performance.
  • Ensure the charging station is placed with adequate clearance (0.5m on sides, 1.5m in front) and away from signal interference like routers or mirrors to prevent issues with finding the station.
  • If the robot falls off stairs, clean the cliff sensors on the bottom and restart.
  • If the robot is not collecting dirt, check and clean the dustbin filter.
  • If the robot moves in circles or cleans in small areas, check and clean the wheels and nose wheel for obstructions like hair.

Warranty & Support

The ILIFE T20s Ultra comes with a 2-year warranty.

For more detailed information or if you encounter any issues with your robot, please visit www.iliferobot.com for further assistance.

You can also contact ILIFE Customer Service:

Stay connected with ILIFE on X (formerly Twitter) at https://x.com/ilife_Global for product updates, maintenance tips, video demonstrations, and exclusive benefits.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.