1. Introduction
The YIERYI YY-1104 6-in-1 Soil Tester is a professional-grade tool designed for comprehensive soil analysis. It primarily measures soil fertility, soil moisture, soil temperature, and provides rapid determination of nitrogen (N), phosphorus (P), and potassium (K) content. This device is suitable for a wide range of applications including pot cultivation, greenhouse cultivation, landscaping, and general agricultural planting, helping you take the guesswork out of gardening.

2. Package Contents
Please check the package contents upon receipt:
- 1 x YIERYI YY-1104 6-in-1 Soil Tester
- (3 x AAA batteries are NOT included and must be purchased separately)

3. Product Overview
Familiarize yourself with the components of your soil tester:

- Hook: For hanging or storage.
- LCD Display Screen: Shows Fertility, NPK, Temperature, and Humidity readings.
- ON/OFF Button: Powers the device on and off.
- MODE Button: Switches between measurement functions and temperature units.
- Probe: Dual stainless steel probes for soil insertion and measurement.

4. Setup
4.1 Battery Installation
- Locate the battery compartment on the device.
- Open the battery compartment cover.
- Insert 3 x 1.5V AAA batteries, ensuring correct polarity (+/-).
- Close the battery compartment cover securely.

5. Operation
5.1 Powering On/Off
- Powering On: Press the ON/OFF button to switch on the device. The screen will display a full image for 3 seconds before entering the measurement readiness state.
- Powering Off: While the device is powered on, press the ON/OFF button once to switch it off. The device will also automatically power down after 3 minutes of inactivity.
5.2 Taking Measurements
- Insert the instrument probe into the soil sample to be tested, ensuring a minimum insertion depth of 10cm.
- Press the MODE button to commence measurement.
- Allow the reading to stabilize on the LCD screen.
5.3 Function Switching (Short Press MODE)
Short press the MODE button to cycle through the measurement functions in the following sequence:
- Fertility
- Nitrogen (N)
- Phosphorus (P)
- Potassium (K)
The device also continuously displays Soil Humidity and Soil Temperature.
5.4 Temperature Unit Switching (Long Press MODE)
Press and hold the MODE button for 6 seconds to switch the temperature unit between °C (Celsius) and °F (Fahrenheit).
5.5 Low Battery Indication
When the battery power is low, the screen will display only the battery indicator symbol, which will flash, indicating that the batteries need to be replaced.

6. Precautions
- Probe Contact: Ensure the probe makes full contact with the soil and is firmly pressed to guarantee data accuracy.
- Unsuitable Soil Types: The soil tester is designed for soil analysis only. It is not suitable for liquids, sandy soils, coconut coir, humus pine needle soil, granular soils, or similar mixtures. These materials possess excessive density or porosity, preventing the probe from fully enveloping the sample, which may cause significant measurement errors or render the instrument inoperable.
- Measurement Accuracy: To enhance measurement accuracy, employ a multi-point sampling method and calculate the average value.
- Avoid Obstructions: During use, avoid striking stones or other hard objects at the test point.
- Avoid Excessive Force: Do not apply excessive force, and refrain from inserting the probe into overly dry or hard soil, as this may damage the electrodes. If insertion proves impossible, relocate to a different test point.
- Extended Soil Insertion: Do not leave the instrument inserted in soil for extended periods. Soil's acidic properties may corrode the probe over time, compromising accuracy and service life.
- Electronic Device Care: This is an electronic device. Avoid dropping or crushing it. It is NOT waterproof – do not immerse in water!

7. Maintenance
- After completing each measurement, switch off the instrument.
- Rinse the probes thoroughly with clean water.
- Wipe the probes clean and dry before storing the device.
- Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Inaccurate readings | Poor probe contact, unsuitable soil type, dirty probes, single-point sampling. | Ensure full probe contact. Use in suitable soil types. Clean probes thoroughly. Use multi-point sampling and average readings. |
| Device does not power on | Batteries incorrectly installed, dead batteries. | Check battery polarity. Replace with fresh AAA batteries. |
| Probe damage | Excessive force during insertion, striking hard objects. | Avoid forcing the probe into hard/dry soil. Relocate to a softer test point. Avoid striking stones. |
| Readings fluctuate or do not stabilize | Insufficient probe insertion depth, unstable soil conditions. | Ensure minimum 10cm insertion depth. Wait for readings to stabilize. |
9. Specifications
| Parameter | Value |
|---|---|
| Model | YY-1104 |
| Functions | NPK, Fertility, Humidity, Temperature |
| NPK Range | 0~1999 mg/kg |
| Fertility Range | 0~1999 µS/cm |
| Humidity Range | 0% ~ 99% |
| Temperature Range | 0°C ~ 60°C (32°F ~ 140°F) |
| Display | Large LCD with Backlight, 90° Foldable / Rotatable |
| Battery Type | 3 * 1.5V AAA Batteries (Not included) |
| Probe Material | High-Quality Stainless Steel |
| Device Material | Durable ABS |
| Dimensions | 265 * 58 * 38mm |
| Weight | 102g (without batteries), 145g (with packaging, without batteries) |
| Probe Length | 210mm |
| Probe Diameter | 5mm |
| Voltage | 4.5V |
| Auto Shutdown | After 3 minutes of inactivity |
| Certification | CE |


10. User Tips
- For the most accurate results, always use the multi-point sampling method and average the readings from several spots in your testing area.
- Ensure the probes are thoroughly cleaned before and after each use to prevent contamination and ensure longevity.
- Take advantage of the 90° rotatable display to comfortably read measurements, especially when testing low-lying plants or in awkward positions.
- If you encounter difficulty inserting the probe, try moistening the soil slightly or choosing a different spot to avoid damaging the probes.
11. Warranty and Support
For detailed warranty information, technical support, and further documentation, please refer to the official user manual PDF: