1. Introduction
Thank you for choosing a smart car refrigerator. This manual provides detailed instructions to help you understand the functions and operation requirements of your Foursun car refrigerator, ensuring you get the best experience from your product.
The Foursun car refrigerator is designed with advanced features:
- High-quality DC variable frequency compressor for efficient, energy-saving, and reliable mobile refrigeration.
- Microcomputer intelligent control system for easy and accurate temperature management.
- Innovative dual temperature zone function with free switching between freezing and refrigeration.
- Compatible with DC 12V/24V and AC 100-240V power inputs, suitable for various environments (car, marine, home, outdoor).
- Voltage detection and low voltage protection to prevent car battery over-discharge.
- Inner container made of food-grade plastic, ensuring safety, leak-proof, and odor-free use.
- Built-in LED lighting for convenience in low-light conditions.
- High-definition LED digital display for clear readings.
- Intelligent touch operation buttons with keyboard child lock function.
- Drainage plug for convenient water removal and odor prevention.
- USB charging port (5V / 1A) for charging small devices.
2. Product Safety and Precautions
Product Use Safety
- Do not touch exposed power cords or power sockets with wet hands.
- Ensure power supply lines and fuses have sufficient current when using onboard.
- Seek professional installation if using an AC device in vehicles.
- Ensure power is connected correctly.
- Do not submerge the product in water.
- Do not freeze cans or beers at extremely low temperatures.
- Do not place other electrical equipment inside the refrigerator.
- Only qualified professionals should perform maintenance.
- Avoid prolonged exposure to rain or strong sunlight.
- After receiving and unpacking, let the refrigerator stand upright for more than 6 hours before use.
Precautions for Use
- Place the refrigerator in a well-ventilated area to facilitate heat dissipation. Ensure a gap of over 100 mm between the compressor's cooling hole and other objects.
- Avoid leaving the door open for extended periods to prevent frost formation and maintain cooling efficiency.
- Do not clean the refrigerator by submerging it in water.
- Do not use the refrigerator near heat sources, as this will reduce its performance.
- Use the refrigerator on a flat, stable surface. Avoid prolonged use on uneven ground to prevent damage and reduced efficiency.
3. Product Overview
The Foursun car refrigerator features a robust design with user-friendly components:
- Refrigerator Door: Dual lids for independent access to each zone.
- Door Button Handle: Secure latches for the lids.
- Cutting Board: Integrated into one of the lids for convenience.
- Lateral Tie Rod: Extendable pull handle for easy transport.
- Control Panel: Located on the front, with touch buttons and LED display.
- Power Interface: For connecting DC or AC power.
- Wheel: Durable rubber wheels for portability.
- Compressor Cooling Port: Ventilation area for the compressor.

4. Setup
Before You Start
- Read all instructions carefully.
- Retain instructions for future reference.
- Separate and count all parts and hardware.
- Follow each step in the proper order.
- Assemble the product near its intended use location to avoid unnecessary movement.
- Always place the product on a flat, steady, and stable surface.
- Keep small parts and packaging materials away from children to prevent choking hazards.
Initial Placement and Power Connection
- After unpacking, place the refrigerator upright on a flat surface and allow it to stand for at least 6 hours before connecting power. This allows the refrigerant to settle.
- Ensure the refrigerator is in a well-ventilated area, with at least 100mm clearance around the compressor cooling port.
- Connect the appropriate power cord:
- For car use: Plug the DC 12V/24V power cord into your vehicle's cigarette lighter socket.
- For home use: Use the AC 100-240V power adapter and cord to plug into a standard wall outlet.

5. Operating Instructions
Control Panel Overview
The control panel features:
- Cool Down Button (Down Arrow): Decreases temperature.
- Warm Up Button (Up Arrow): Increases temperature.
- Set Button: Enters settings mode, switches compressor mode.
- Power Button: Turns the unit on/off.
- Charge Port (USB): 5V/1A output.
- LED Display: Shows current temperature, set temperature, working mode, and battery protection level.
Temperature Control Range
- Control Range: -20°C to 20°C (-4°F to 68°F)
- Display Range: -30°C to 50°C (-22°F to 122°F)
- Standard Voltage Input: DC 12V/24V, max 30V
Refrigerator Start-up/Stop
- Connect the DC12/24V power supply.
- If in standby (display shows "OFF" when touched), hold the Power button for 3 seconds to start.
- The display will show current temperature and working mode. After a 1-minute delay, the compressor will start.
- To stop, hold the Power button for 3 seconds while the keyboard is unlocked.
Keyboard Locking and Unlocking
- Hold the Up and Down arrow buttons simultaneously for 3 seconds to switch to locking mode. The child lock icon will light up.
- The keyboard locks automatically if no operation occurs for 20 seconds.
Temperature Setting
- Press the Up or Down arrow buttons to adjust the temperature. Each press changes the temperature by 1 degree.
- Hold the button to quickly adjust the temperature.
- The set temperature will be saved automatically if no change occurs within 5 seconds.
Compressor Working Mode (ECO/MAX)
- Press the Set button to switch between "ECO" (energy-saving) and "MAX" (rapid cooling) modes.
- Use "MAX" for quick cooling to a lower temperature.
- Use "ECO" to save energy when maintaining a constant temperature.

Low Voltage Protection Setting
This product has a low voltage protection function to prevent battery damage. When battery voltage drops below the set value, the compressor stops (indicated by "E 1" on display). It restarts when voltage returns to normal for 1 minute. The factory default is "Mid-Range".
- Unlock the keyboard.
- Hold the Set button for 3 seconds until a beep.
- Press the Set button again; one of the battery protection level icons (L, M, H) will flash.
- Press the Up/Down arrow buttons to change the setting.
| Battery Protection | 12 V Turn Off | 12 V Turn On | 24 V Turn Off | 24 V Turn On |
|---|---|---|---|---|
| Low grade - L | 8.5 V | 10.9 V | 21.3 V | 22.7 V |
| Medium - M | 10.1 V | 11.4 V | 22.3 V | 23.7 V |
| High grade - H | 11.1 V | 12.4 V | 24.3 V | 25.7 V |
Note: If the refrigerator enters battery protection early, the low voltage protection value might be set too high, or the DC power supply is wired incorrectly. Check wiring and consider lowering the protection gear. For reliable car starting, set protection to "H" when using the refrigerator in the car.
L and R Temperature Zones Closing Setting
The L (left) and R (right) temperature zones can be closed independently, but not simultaneously.
- When setting the temperature, the L temperature zone flashes. Press the Set button to close the L zone (display shows "OFF"). Press Set again to display the normal temperature.
- After pressing Set again, the R temperature zone flashes. Press the Set button to close the R zone (display shows "OFF"). Press Set again to display the normal temperature.

6. Maintenance
Cleaning
- Before cleaning, disconnect the power supply.
- Wipe the inner and outer surfaces with a cleaning cloth dampened with water or mild detergent.
- Do not wash directly with water to avoid damaging electrical components.
Long-Term Storage
If the refrigerator will not be used for a long time:
- Clean the inside and outside thoroughly.
- Ensure it is completely dry.
- Take moisture-proof and dust-proof measures to prevent mildew and odors.
7. Troubleshooting
Error Code Description
If the compressor, module, fan, temperature sensor, or input voltage is abnormal, an error code will appear, and the compressor will stop. To resolve, unplug and replug the power supply after eliminating the abnormality. The temperature display will return, and the compressor will restart in refrigeration mode after 1 minute.
| Error Code | Problem | Solution |
|---|---|---|
| E 0 | Temperature sensing head is damaged | Check or replace the temperature sensor |
| E 1 | Input voltage is too low | Check input voltage and adjust battery protection level |
| E 2 | DC fan over current protection | Check the cooling fan |
| E 3 | Abnormal start of compressor | Turn off power and let stand for 30 minutes |
| E 4 | Abnormal compressor speed | Adjust compressor operation mode (MAX/ECO) |
| E 5 | Module temperature too high | Move refrigerator to a ventilated place to lower module temperature |
| E 6 | Module hardware failure | Power on after 30 min of power failure; if fault persists, module needs replacement |
Frequently Asked Questions
If the product does not work properly:
- Check if power is on.
- Check if voltage is too low.
- Check all connections from battery to refrigerator for looseness or poor contact.
- Check the fuse.
- Check if the refrigerator is turned on.
- Check if the temperature is set too high.
If refrigeration performance is poor:
- Too much food is in the refrigerator.
- Food temperature is too high.
- Door is not closed properly.
- Door seal (sealing ring) is damaged.
- Ventilation around the refrigerator is poor.
- Environment temperature is too high.
- Incorrect temperature setting.
Unusual Noises:
- "Water flowing" sound: Normal, caused by refrigerant flow.
- Loud sound at startup: Check if placed on a flat surface, check for surrounding vibrations. A slightly louder sound at compressor startup (static to high speed) is normal and will decrease once speed stabilizes.
Water Drops:
- Water drops around shell or door seal: Normal in humid air as moisture liquefies and condenses on cooler surfaces.
8. Specifications
| Parameter | FS-C40 Max | FS-C50 Max |
|---|---|---|
| Input Voltage | DC 12V/24V, AC 100-240V | |
| Temperature Control Range | -20°C ~ 20°C (-4°F ~ 68°F) | |
| Refrigerant | R600a | |
| Insulation Material | Polyurethane foam | |
| Rated Power | 45W ±20% | |
| Rated Current | 3.75A/1.875A | |
| Net Weight | 18.3 kg | 18.8 kg |
| Product Dimensions (L*W*H) | 765*470*466 mm | 765*470*516 mm |
| Packing Dimensions (L*W*H) | 775*525*535 mm | 775*525*585 mm |
9. User Tips
- Maximize Dual Zones: Utilize the independent temperature control to set one compartment as a freezer for meats and ice cream, and the other as a refrigerator for drinks and fresh produce. This flexibility is a major advantage for varied storage needs.
- Battery Management: For longer trips, especially when using the freezer function, monitor your vehicle's battery or use an external power station to ensure continuous operation without draining your car battery. The low voltage protection feature is helpful, but proactive management is best.
- Quick Cooling: If you need to cool items rapidly, switch the compressor mode to "MAX". Once the desired temperature is reached, you can switch back to "ECO" mode to save energy.
- Power Source Check: If the refrigerator stops unexpectedly or displays an "E 1" error, first check your power connection and the battery protection level setting. Adjusting the protection level to "H" is recommended for car use to ensure your vehicle starts reliably.
- Capacity Planning: The 50L model can hold a significant amount (e.g., 64 cans of 330ml cola). Plan your packing to make the most of the space, especially for longer trips.
- Portability: Make full use of the side pull rod and rubber pulleys for easy transport, especially when the unit is full and heavy.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to your purchase documentation or contact the seller directly. Keep your proof of purchase for any warranty claims.
A digital version of this user manual is available for download. Please refer to the provided PDF document for additional details: User Manual (PDF)