1. Product Overview
The ANDELI MIG-205DP is a versatile 8-in-1 multi-process IGBT inverter welder and plasma cutter. It supports a wide range of welding and cutting applications, including Pulsed MIG, Gas MIG, SYN/MAN MIG, HF TIG, CUT, Clean, Cold, Spot Welding, and MMA Aluminum Welding. This machine is designed for both household and workshop use, offering high efficiency and adaptability for tasks from thin sheet metal fabrication to heavy-duty repairs.

1.1 Key Features
- 8-in-1 Multi-Process: Combines Pulsed MIG, Gas MIG, SYN/MAN MIG, HF TIG, CUT, Clean, Cold, Spot Welding, and MMA Aluminum Welding.
- Dual Voltage: Operates on both 110V and 220V, 50/60 Hz power supplies, ensuring compatibility for various environments.
- High Output: Delivers a maximum welding current of 205A and a maximum cutting current of 50A.
- Smart Interface: Features a 5-inch large HD LED display and intuitive rotary knob for easy selection of process, material, thickness, and functions.
- Advanced Control: Supports professional adjustments for inductance, slow wire feeding, pre/post gas timing, Initial/Finish Current, anti-stick, thrust, and VRD.
- MCU-based Digital Control: Ensures consistent, stable performance even with temperature or component variations.
- HF Arc Start: Built-in HF arc start for TIG (non-contact) and HF pilot arc for plasma cutting, handling painted, rusty, and uneven surfaces.
- Cold Welding Mode: Exclusive TIG mode for low-heat welding, minimizing distortion on thin stainless/carbon steel.
- Cleaning Function: Dedicated function for post-weld cleaning, removing oxidation and discoloration from stainless welds.
- Robust Protection: Advanced auto-protection shuts down the unit in case of voltage fluctuation, overheating, or other abnormalities, with automatic restart when conditions stabilize.
- Memory Function: Automatically saves and recovers welding parameters, reducing downtime and ensuring repeatable precision.


2. Safety Information
Your safety is paramount. Please read and understand all safety precautions before installing, operating, or repairing this equipment. Always think before you act and be careful.
2.1 General Safety Precautions
- Read the Manual: Do not install, operate, or repair this equipment without reading this manual and all safety precautions.
- Qualified Personnel: All installation, operation, maintenance, and repair procedures must be performed only by qualified individuals.
- Work Area: Ensure the work area is organized, well-lit, and free of all flammables. Have a fire extinguisher and sand bucket readily available.
- Ventilation: Use sufficient ventilation or exhaust at the arc to keep fumes and gases away from your breathing zone. Operate engines in open, well-ventilated areas or vent exhaust fumes outdoors.
- Protective Equipment: Always wear correct eye, ear, and body protection, including a welding helmet with proper filter, protective clothing (woolen, flame-proof apron, gloves, leather leggings, high boots), and safety glasses. Protect others with screens or barriers.
- Equipment Condition: Ensure all protective equipment is in good condition.
- Children: Keep children away from the welding area.
- Pacemakers: Pacemaker wearers should consult their doctor before operating.
2.2 Electrical Safety
WARNING: ELECTRIC SHOCK CAN KILL.
- The electrode and work circuits are electrically "hot" when the welder is on. Do not touch these parts with bare skin or wet clothing.
- Wear dry, hole-free gloves to insulate hands.
- Insulate yourself from work and ground using dry insulation.
- Ensure the machine is plugged into a grounded receptacle per national, local, or applicable electrical codes.
- Always ensure the work cable makes a good electrical connection with the metal being welded, as close to the welding area as possible.
- Maintain the electrode stinger, work clamp, welding cable, and welding machine in good, safe operating condition. Replace damaged insulation.
- Never dip the electrode in water for cooling.
- When working above floor level, use a safety belt to protect yourself from a fall if you get a shock.
- Disconnect the welder from its AC power source and wait several minutes for electrical energy to discharge before removing side panels for maintenance.
2.3 Fumes and Gases
WARNING: FUMES AND GASES CAN BE DANGEROUS.
- Avoid breathing fumes and gases produced by welding. Keep your head out of the fume.
- Use enough ventilation and/or exhaust at the arc to keep fumes and gases away from the breathing zone.
- Do not weld in locations near chlorinated hydrocarbon vapors (from degreasing, cleaning, or spraying operations) as they can form highly toxic gases.
- Shielding gases can displace air and cause injury or death. Always use enough ventilation, especially in confined areas.
- Read and obey the Safety Data Sheet (SDS) and warning labels on all welding materials containers.
2.4 Welding and Cutting Sparks
WARNING: WELDING AND CUTTING SPARKS CAN CAUSE FIRE OR EXPLOSION.
- Remove all fire hazards from the welding area. If not possible, cover them to prevent sparks from starting a fire.
- Have a fire extinguisher readily available.
- Do not heat, cut, or weld tanks, drums, or containers until proper steps have been taken to ensure they are free of flammable or toxic vapors. They can explode even if