VTOMAN V-Truck

Contents

VTOMAN V-Truck 6000A Car Battery Jump Starter

Model: V-Truck (JS-381)

VTOMAN V-Truck 6000A Jump Starter

The VTOMAN V-Truck 6000A Car Battery Jump Starter is a powerful and versatile device designed to jump start 12V and 24V vehicles, and also functions as a portable power bank and LED flashlight.

Important Safety Warnings

WARNING:

  1. Please read the instructions carefully before using this product.
  2. The product is used for 12V or 24V vehicle engine start. It may lead to damage or be dangerous if used for other different voltage platform machines.
  3. DO NOT use it if the battery clamps or battery cables are damaged.
  4. This product is not intended to be used as a replacement vehicle battery.
  5. Please ensure all vehicle's battery terminals are clean and battery clamps are connected properly before jump starting the vehicle. Dirty or corroded battery terminals may affect starting performance.
  6. DO NOT crank the engine for more than 3 seconds at a time. The jump start feature is designed for short term operation only. Operating the jump start feature for more than 3 seconds may cause damage to the unit. Allow the jump starter to cool down for at least 2 minutes after each cranking.
  7. Please remove the battery clamps from the vehicle battery immediately after the engine has successfully started, otherwise it may cause damage.
  8. Always ensure connecting the jumper cables to the vehicle's battery terminals must be positive to positive (red clamp to battery "+") and negative to negative (black clamp to battery "-").
  9. NEVER allow the red and black clamps to touch each other or a common piece of metal.
  10. This product is not for use by children and should only be operated by adults.
  11. DO NOT expose product to rain, snow or use in damp conditions. NEVER submerge unit in water.
  12. DO NOT operate the product in an explosive environment, such as flammable liquids, gases or dust.
  13. DO NOT modify or disassemble the product.
  14. Be sure to remove all metal items (watches, necklaces, rings, etc.) before using the jump start system.
  15. DO NOT operate the unit if it has received a sharp blow, been dropped or otherwise damaged in any way. It must be tested by a qualified battery technician.
  16. DO NOT place the product in an environment where the temperature exceeds 60°C.
  17. Please charge only at ambient temperatures between 0°C and 45°C.
  18. Please use the original charger to charge the product.
  19. If this unit is leaking liquid, dispose of it at a proper recycle facility immediately.
  20. Always wear eye protection when working with batteries. Batteries can explode and cause flying debris.
  21. If battery acid comes into contact with eyes, flush affected area with running water immediately for at least 15 minutes and seek medical attention immediately.
  22. If battery acid comes into contact with skin, rinse immediately with water and wash thoroughly with soap and water. If redness, pain or irritation occurs, seek medical attention immediately.
  23. Always ensure someone is nearby to help you in an emergency.
  24. Products based on lithium batteries are disposed of at the end of their life in accordance with local regulations.

Product Layout

Familiarize yourself with the components of your VTOMAN V-Truck Jump Starter.

Detailed product layout diagram with labeled parts

This diagram illustrates the various ports, buttons, and indicators on the VTOMAN V-Truck Jump Starter, essential for proper operation.

A. Product Layout Legend
No. Component No. Component
1.Battery Clamps7.Flashlight Button
2.LED Flashlight8.12V Override Button
3.Battery Level Indicator9.24V Override Button
4.Warning Light10.29V/5A DC Input Port
5.12V Mode Indicator11.USB-C Input Port
6.24V Mode Indicator12.USB-A Output Ports

Setup and Charging

Battery Status

Press any button to illuminate the Internal Battery Level Indicator LEDs, showing the battery capacity level.

Battery Level Indicator 25% LED Flashing 1 LED solid On 2 LEDs solid On 3 LEDs solid On 4 LEDs solid On
Battery Level0%<25%<50%<75%<100%

During charging, the indicator LEDs will flash and become solid one by one. When a level is reached, the corresponding LED will be solid, and the next level LED will flash until all four LEDs are solid. They will then turn off, indicating the end of charging.

Recharging

This product has two input ports: a 29V DC input port and a USB-C input port. The two input ports do not support simultaneous charging; the 29V DC input is prioritized.

  1. Fast Charge: Connect the 29V AC adapter (included) to the 29V DC input port.
  2. Slow Charge: Connect a USB-C cable to the unit's USB-C input port, then connect the other end of the USB-C cable to any powered USB power port (e.g., USB wall charger or USB car charger, not included).
Jump starter being charged, illustrating 145W fast charging

The image shows the jump starter connected to a wall outlet for charging, highlighting its 145W fast charging capability, which allows it to reach full charge in approximately 1.5 hours.

IMPORTANT:

  • Please charge only at ambient temperatures between 0°C and 45°C.
  • Recharge the battery after each use or at least every 6 months when in storage to prolong battery life and keep the unit ready for use.

Jump Start Vehicle Operation

IMPORTANT:

  • Do not attempt to jump start an engine if the battery level is at 25% indicator.
  • This product is built with 12V and 24V two modes for 12V and 24V platform vehicles. Always make sure the unit is on the correct mode to match vehicles (12V mode for 12V vehicles, 24V mode for 24V vehicles).
  • DO NOT crank the engine for more than 3 seconds at a time. The jump start feature is designed for short term operation only. Operating the jump start feature for more than 3 seconds may cause damage to the unit. Allow the jump starter to cool down for at least 2 minutes after each cranking.
  1. Press any button to turn the unit on and check the battery level indicator. If less than 25%, recharge the unit before attempting a jump start.
  2. Connect the red clamp to the POS "+" terminal of the vehicle battery.
  3. Connect the black clamp to the NEG "-" terminal of the vehicle battery.
  4. Check the 12V and 24V mode LEDs, and warning light on the unit, then proceed accordingly based on the table below.
Step-by-step diagram for jump starting a 12V/24V vehicle

This diagram visually guides users through the four steps of jump starting a 12V or 24V vehicle: connecting jumper cables, selecting voltage, starting the vehicle, and removing clamps.

LED Status During Jump Start
LED Status Description Action
12V LED or 24V LED flashing or solid On.Good connection.Proceed with jump start attempt.
RED warning light solid On.Connection is reversed.Reconnect the clamps connections correctly.
12V and 24V LEDs flashing at same time.Vehicle battery is low, the unit cannot identify the vehicle battery system is 12V or 24V.OVERRIDE mode will be required. See USING OVERRIDE MODE.
No any LEDs on.No connection detected: 1. Poor connection between clamps and battery terminals, 2. Vehicle battery voltage extremely low.Check to ensure a clean and solid connection between clamps and battery terminals. If after checking that clamps have a good connection both LEDs are OFF, the use of OVERRIDE mode will be required. See USING OVERRIDE MODE.

Using Override Mode

This product has an OVERRIDE feature which allows you to force ON the jump starter function, enabling you to boost discharged batteries as low as 0 volts.

CAUTION: USE THE OVERRIDE MODE WITH EXTREME CARE

  • Both the spark proof and reverse polarity protection features are disabled.
  • Pay very close attention to the polarity of the battery before using this mode.
  • DO NOT allow the positive and negative battery clamps to touch each other or a common piece of metal as the product will generate sparks.
  • DO NOT connect a 12V vehicle if the 24V OVERRIDE mode is activated.
  • DO NOT connect a 24V vehicle if the 12V OVERRIDE mode is activated.
  • This mode uses very high current that can cause sparks and high heat if not used properly.
  • If you are unsure whether the vehicle battery system is 12V or 24V, please seek vehicle service or professional help.
  • If you are unsure about using this mode, do not attempt it and seek professional help.
  1. ENSURE CORRECT POLARITY (red clamp to POS "+" terminal of the battery and black clamp to the NEG "-" terminal of the battery).
  2. ENSURE your vehicle battery system is 12V or 24V, then press and hold the 12V or 24V Mode button for 2 seconds accordingly.
  3. The 12V LED or 24V LED will be solid on, indicating that the OVERRIDE mode is enabled.
  4. Proceed with the jump start attempt within 30 seconds.

Note: The OVERRIDE mode will only be active for 30 seconds. Once 30 seconds have passed, the product will reset.

USB Power and LED Flashlight

USB Power

This product is equipped with two USB-A output ports, ideal for charging portable electronic devices such as smartphones, tablets, and more.

  1. Connect device(s) to the USB output port(s) using a matched USB charge cable.
  2. Press any button to turn the unit on and activate USB power.

LED Flashlight

Press the flashlight button to activate the LED flashlight. Keep pressing the button to cycle through the 4 options: 100% -> Strobe -> SOS -> Off.

Man using the jump starter's LED flashlight in a garage

The image demonstrates the jump starter's integrated LED flashlight being used in a low-light environment, highlighting its utility beyond jump-starting.

Technical Specifications

Attribute Value
Dimension270*189*159.7mm
Weight2.9kg
Battery Capacity133.59Wh / 36400mAh
Output2 x USB-A (5V=2.4A; 5V=1A), 12V/24V Jump Start, 3W LED Flashlight
InputDC 29V=5A; USB-C (5V=2A; 9V=2A)
Full Charge TimeAbout 1.5 hours
Peak Current6000A
Operating Temperature-40°C~60°C / -40°F~140°F
Charging Temperature0°C~45°C / 32°F~113°F
Storage Temperature-40°C~60°C / -40°F~140°F
Diagram showing the 10 intelligent protection systems

The image highlights the 10 intelligent protection systems integrated into the jump starter, including over-charge, short-circuit, smart-AI, spark-proof, reverse-polarity, over-current, over-discharge, high-temperature, over-voltage, and reverse-charge protection.

Package Contents

The VTOMAN V-Truck Jump Starter package includes:

  • V-Truck Jump Starter (Host)
  • 145W AC Adapter
  • USB Charging Cable
  • User Manual
Contents of the product package including the jump starter, AC adapter, USB cable, and user manual

This image displays all items included in the VTOMAN V-Truck Jump Starter package, ensuring users can verify they have received all necessary components.

Troubleshooting Guide

Problem Possible Cause Solution
The unit cannot be activated by pressing any buttons.Over-discharge protection may be activated.Please recharge the unit. If it still cannot activate after recharging, please contact after-sales service.
The unit cannot be recharging.1. No power from AC adapter or USB port.
2. Faulty USB cable.
1. Please change AC adapter or plug into a different USB outlet.
2. Replace USB cable. If it still cannot charge, please contact after-sales service.
The 12V LED flashing or solid on but it still cannot jump start the vehicle.1. The vehicle battery system is 24V, but the battery voltage dropped in 12V.
2. Mechanical issue with vehicle.
1. ENSURE your vehicle battery is 24V, if Yes, you can use 24V OVERRIDE mode. See USING OVERRIDE MODE.
2. Seek vehicle service or professional help.
RED warning light flashing.Over-temperature protection is activated.Stop using and wait for the unit to cool down.
The 25%/50%/75% three LEDs flashing together when recharging the unit.Internal battery temperature is too low, recharging is forbidden.Move to a room temperature area, and recharge after the internal battery has warmed up.
25%/50% two LEDs or 50%/75% two LEDs flashing together when recharging the unit.The AC adapter is not original and does not match the unit.Please use the original AC adapter to charge the unit.
25% one LED fast flashingInternal battery over-discharged.Please contact after-sales service if the unit is still under warranty, or purchase a new one.

Frequently Asked Questions

  1. Q: Can this product automatically identify 12V and 24V vehicle batteries?
    A: Yes. It is OK in normal condition, but it cannot be identified under abnormal conditions such as low vehicle voltage or no battery. When this happens, you need to activate the OVERRIDE MODE manually.
  2. Q: How many times can this product jump start the vehicle?
    A: In normal condition, with a full charge, the unit can start about 70 times for 12V vehicles and 45 times for 24V vehicles.
  3. Q: How long does it take to charge this product?
    A: It needs about 1.5 hours if using the original 29V AC adapter.
  4. Q: How many times can this product charge a phone?
    A: It depends on the capacity of the phone battery. For example, a full charge can charge an iPhone 12 about 15 times.
  5. Q: What is the lifespan of the product?
    A: It can be used for 3-5 years under normal conditions.
  6. Q: How long can the product be stored after being fully charged?
    A: With patented technology, a fully charged unit can be stored for 3 years without problems. However, to extend the service life, it is recommended to use and recharge it every 6 months.

User Tips

  • For optimal battery longevity, ensure to use and recharge the jump starter at least every 6 months, even if not in active use.
  • Always keep battery terminals clean for reliable jump-starting performance.
  • If the unit cannot detect the battery voltage (e.g., very low battery), remember to use the OVERRIDE mode with extreme caution, ensuring correct polarity.
  • The VTOMAN V-Truck is suitable for heavy 24-volt trucks, as confirmed by user questions.

Maintenance and Environmental Protection

Toxic and Harmful Substances

Composition and amount of toxic and harmful substances in the product:

Pb Hg Cd Cr(VI) PBB PBDE
OOOOOO

O: Indicates that the content of hazardous substances in all homogeneous materials is below the MCV limit specified in Standard 2002/95/EC (RoHS).

Environmental Protection

Do not dispose of this product with regular household garbage at the end of its life cycle. Hand it over at a collection point for the recycling of electrical and electronic appliances. The symbols on the product, in the instructions for use, or on the packaging will inform you about the methods for disposal.

Warranty and Customer Support

  • Warranty: 18 Months Limited Warranty Service
  • Technical Support: Lifetime Technical Service
  • Email Support: Support@vtoman.com
  • More Information: Visit www.VTOMAN.com

For additional guides and documents, you may refer to the official PDF user manual available at this link.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.