ROBORE U18F

Contents

ROBORE U18F Treadmill User Manual

Model: U18F | Brand: ROBORE

1. Important Precautions

IMPORTANT!

Your satisfaction is very important to us. If you encounter any issues such as shipping damage, missing parts, error code, or defects, please contact us for a satisfactory solution. Do not return until you have contacted us.

Support E-Mail: service_sports@163.com

Please provide your Order ID and a description of the product problem (attached pictures or videos if necessary).

To decrease the risk of severe injuries, read carefully all important instructions and warnings before using the treadmill.

  • Health Consultation: Before starting any workout program, consult your doctor. This is especially important for individuals older than 35, those with health problems, and pregnant women.
  • Environment: Keep the equipment in an enclosed area, away from dust or humidity. Do not store it in a garage, indoor backyard, or near water. Humidity, dust, and water can lead to malfunction and void the warranty.
  • Placement: Place the unit on a flat surface. Uneven surfaces can affect proper functioning. Some models may include levelers behind the legs; refer to the manual for details.
  • Ventilation: The unit must be placed in a ventilated area. Avoid using it in places with sprays or oxygen dispensers, as this can affect air quality and cause accidents.
  • Safety Distance: Keep children younger than 12 years old and pets away from the equipment. Maintain a safe distance.
  • Weight Capacity: Check the manual for the maximum weight the equipment can support. Exceeding this weight can lead to malfunction not covered by the warranty. (Max load: 300 lbs / 136kg)
  • Power Supply (if applicable): Ensure the power cord and plug are in good condition. Connect only to a grounded circuit to prevent damage. Keep power cords away from hot surfaces.
  • Battery-Powered Units (if applicable): Ensure batteries are sufficiently charged for the display to function fully.
  • Electric Supply Units (if applicable): Adjust speed gradually to avoid sudden changes and ensure safety. Never leave the machine unattended while it's working.
  • Maintenance: Regularly check and tighten all screws, as vibrations can cause them to loosen. Damages due to lack of maintenance are not covered by the warranty.
  • Unpacking: Two people are needed to remove the unit from its package to prevent damage not covered by the warranty.
  • Obstruction: Do not let any object fall into the grooves.
  • Cleaning/Post-Workout: If the unit works through a power cord, unplug it before cleaning, after a workout, and before performing any maintenance.
  • Discomfort: If you start feeling pain or dizziness while training, STOP IMMEDIATELY.
  • Preservation: Preserve the original packaging, protections, manual, and components during the guarantee period.
  • Recycling: This electronic product must be recycled according to applicable local laws to preserve the environment. Do not dispose of it in municipal rubbish bins. Contact your local council for recycling procedures.

KEEP THE PURCHASE RECEIPT TO ACCESS SERVICE. KEEP THIS ADVICE FOR FUTURE REFERENCES.

2. Product Features and Parts List

2.1 Product Overview

ROBORE U18F Treadmill in use with a person running, showing 15% incline capability.
Figure 2.1: ROBORE U18F Treadmill in operation, highlighting its 15% incline.
ROBORE U18F Treadmill showing different usage scenes (Pet room, Gym, Elderly room, Living room) and manual incline levels (15%, 10%, 2%).
Figure 2.2: Treadmill versatility for various usage scenes and manual incline settings.

2.2 Main Components

Close-up of the treadmill's bright and clear digital display showing Time, Speed, Distance, and Calories, along with the remote control.
Figure 2.3: Digital Display and Remote Control for tracking workout data.
Illustration of the treadmill's quiet and powerful 2.5HP motor, indicating low noise operation below 45dB.
Figure 2.4: Quiet and Powerful 2.5HP Motor for disturbance-free workouts.
Detailed view of the treadmill's 7-layer non-slip running belt and triple shock absorption system.
Figure 2.5: 7-Layer Non-Slip Belt with advanced shock absorption.

2.3 Parts Diagram Description

The treadmill consists of a main body with a running belt, a display panel, and a handle frame. Key components include:

  • Phone holder: Located at the top of the handle frame.
  • Armrest: The side rails of the handle frame.
  • Display: An integrated screen on the front of the treadmill base.
  • Fixed Knob: Used for securing parts, typically near the base.
  • Running belt: The main surface for walking/running.
  • Foot pad: Support pads at the base.
  • End caps: Protective caps at the ends of the treadmill.
  • M4*16 Screw: Used for assembly, typically for the phone holder or armrest.

2.4 Parts List

No.List (Visual Reference)FittingsQty.
1Main Body1
2Hex Wrench1
3Spanner1
4Remote Control1
5Fixing Knob2
6Fold-able Footrests2
7Silicone Boost2
8M4x16 Screws2
9M8x30 Hex Bolt2
10Lock Nut M82
11Phone Holder1
12User's Manual1

3. Setup

The ROBORE U18F Treadmill is designed for quick setup. The main body is largely pre-assembled for immediate use. However, some minor assembly is required for specific components.

3.1 Armrest Installation

The armrest needs to be fixed when needed. Refer to the parts diagram description (Section 2.3) for the location of the M4*16 screws used for this purpose.

3.2 Manual Slope (Incline) Installation

To install the manual slope adjustment:

  1. Use the provided M8x30 screws and M8 nuts.
  2. Fix the folding foot pedals onto the treadmill platform.
  3. Perform the same operation on the other side.
Image showing the manual incline adjustment mechanism with levels at 15%, 10%, and 2%.
Figure 3.1: Manual Incline Adjustment Mechanism.

Please note that the product's slope adjustment is manual, not electric.

4. Operating Instructions

4.1 Remote Control Operation

Remote control for the treadmill with Speed +, Mode (M), Start/Stop (ON/OFF), and Speed - buttons.
Figure 4.1: Treadmill Remote Control.
  1. Step 1: Turn on the power switch of the treadmill.
  2. Step 2: In standby mode, press the "M" key to enter three countdown modes: Time, Distance, and Calorie. During mode selection, the indicator light for the current mode will always be on. Select your desired mode, then use the "+" and "-" keys to increase or decrease the countdown value.
  3. Step 3: After setting the countdown value, press "ON/OFF" to start running.
  4. Step 4: To quit the countdown function or stop the treadmill, press "ON/OFF" again.

4.2 Incline Adjustment

This machine is equipped with two levels of manual incline adjustment. Adjust the angle according to your actual needs.

  • Ensure that the support feet are properly adjusted to avoid unnecessary injuries.
  • The height-increasing foot pads should only be used after the support feet have been fully extended.
  • If the rear cover touches the ground, adjust the height of the rear foot pads by rotating them to prevent scraping against the floor.
Diagram illustrating how to adjust the incline by placing the support leg into the boost for higher incline, showing 'high' and 'low' positions.
Figure 4.2: Manual Incline Adjustment Method.

5. Maintenance

5.1 Running Belt Corrections

If the running belt is offsetting to the left or right or making a rattling noise, adjust it to the correct position.

Running Belt Adjustment Diagram Description: The diagram illustrates how to correct the running belt if it shifts to the left or right. It shows two views: 'To Left' and 'To Right'. Both views depict the treadmill's front and rear rollers. For correction, users are instructed to remove the covers before adjustment and ensure the belt is centered. A note advises to refer to instructions or call support if needed.

If the running belt slips, use a 5mm wrench to turn both side bolts 1/4 clockwise. Repeat this procedure until the belt is properly tightened.

Caution:

  • Heavy pedaling may cause shutdown (overload protection, not machine failure).
  • Current and voltage overload may cause shutdown.
  • Individual running habits (e.g., how hard left or right foot treads) may cause the running belt to shift slightly.

5.2 Lubrication Instructions (for normal belt only)

The treadmill is pre-oiled for instant use. The provided 30ml oil can last about one year under normal circumstances.

Usage FrequencyMaintenance Frequency
<3 Hours/Week2 Months
4-7 Hours/Week1 Month
>8 Hours/Week2 Weeks

How to apply oil (approx. 2.5ml each time):

  1. Turn off the machine first.
  2. Lift the running belt.
  3. Add the oil under the belt.
  4. After applying, start the machine and change to the highest speed. The oil will spread from the middle between the running belt and the board.

A specific indicator that you've applied enough oil is when you touch the middle of the back of the running belt with your hand and feel it's slightly wet with oil.

Image showing a hand applying lubricant under the treadmill's running belt, with a 'Lubrication Schedule' table.
Figure 5.2: Lubrication Process and Schedule.

For a visual guide, you can refer to the Lubricant Instruction Video (PDF reference: User manual (PDF)).

6. Troubleshooting

If you encounter any issues with your treadmill, refer to the table below for common error codes and their solutions.

NO.Error codeDescriptionMaintenance
1E02Hall detection error
  1. Inspect Hall terminal
  2. Replace motor
  3. Replace lower control
2E03Overcurrent error
  1. Replace lower control
3E04Overvoltage error
  1. Inspect external mains input
  2. Replace lower control
4E05Undervoltage error
  1. Inspect external mains input
  2. Replace lower control
5E06Overload error
  1. Inspect if running belt resistance is abnormal
  2. Replace motor
  3. Replace lower control
6E08Lower control overheat error
  1. Inspect if running belt resistance is abnormal
  2. Replace lower control
7E11UVW three wires open circuit error simultaneously
  1. Inspect if motor wires are abnormal
  2. Replace motor
  3. Replace lower control.
8E13Communication failure error
  1. Inspect if communication wires are abnormal
  2. Replace lower control
  3. Replace upper display

7. Specifications

FeatureDetail
Brand NameROBORE
Model NumberROBORE U18F
TypeHome Use Treadmill / Cadio Training
Driving PowerElectric
Motor2.5HP
Noise Level<45 dB
Maximum Speed6.2 MPH (10.5km/h)
Maximum Incline15% (simulates hill climbs)
Manual Incline Levels2% / 10% / 15%
Running Belt Dimensions37" × 15.5" (92.5 × 39 cm)
Max Load Capacity300 lbs (136kg)
FoldableYes
ScreenYes (LED Display)
Data TrackingTime, Speed, Distance, Calories
Control MethodRemote control with storage box
With SpeakersNo
Bluetooth ConnectionNo
With Vibration ModeNo
Heart Rate TestWithout
Training SiteWaist, Legs, Foot
Usage ScenesPet room, Gym, Elderly room, Living room
OriginMainland China
CertificationCE
Input Voltage220-240V
Frequency50 HZ
Product Weight14.9kg
Package Weight17.4kg
Product Size (Unfolded)103.6 × 52.6 × 95 cm
Folded Thickness9 cm
Package Size113.5 × 56 × 10.3 cm

7.1 Package Contents

  • 1 x Treadmill
  • 1 x User Manual
  • 1 x Remote Control
  • 1 x Hex Wrench
  • 1 x Spanner
  • 2 x Fixing Knobs
  • 2 x Fold-able Footrests
  • 2 x Silicone Boost
  • 2 x M4x16 Screws
  • 2 x M8x30 Hex Bolts
  • 2 x Lock Nuts M8
  • 1 x Phone Holder

8. Warranty and Support

8.1 1 Year Warranty

Your treadmill comes with a one-year warranty.

Warranty Description: 1 Year Parts Replacement.

8.2 Customer Support

We are committed to 100% customer satisfaction.

  • Online Support: 7*24 online California-based customer service team available to solve after-sales problems.
  • Customer Service Team: Provides personalized solutions to ensure satisfaction.
  • Exclusive Maintenance Service: We honor our commitment to quality and durability by offering free maintenance tools for orders within 6 months, including lubricants and a remote control.

Support E-Mail: service_sports@163.com

9. User Tips

  • Maximize Incline Training: Utilize the 15% manual incline to simulate uphill running, which can significantly increase calorie burn and improve cardiovascular endurance. Remember, the incline is adjusted manually.
  • Joint Protection: Take advantage of the triple shock absorption system, including the 7-layer running belt, 8 built-in shock absorbers, and 2 external mats, for a comfortable and joint-friendly workout.
  • Quiet Operation: The treadmill's upgraded quiet motor operates below 45 dB, allowing you to exercise without disturbing others in your household.
  • Easy Storage: When not in use, fold the treadmill to its compact 9 cm thickness. Use the built-in wheels for easy mobility and storage in tight spaces like under a sofa or bed.
  • Ready to Use: The treadmill comes largely pre-assembled. After minor setup for the armrest and manual incline, you can start your workout almost immediately.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.