Introduction
This manual provides detailed instructions for the SENSE S10 10-channel radio system, designed for RC model cars, boats, crawlers, buggies, and trucks. Please read this manual thoroughly before operating your device to ensure safe and optimal performance.
Specifications
Transmitter (Model: S10)
- Channels: 10CH+
- Antenna: Built-in single antenna
- Display: 3.13-inch 376x960 full dot matrix IPS display
- Power: 2600mAh 18650 battery + AAA battery x 4 (or 18650 Lipo battery pre-installed)
- Control Range: >200m (open and interference-free ground conditions)
- Dimensions: 124mm x 101mm x 168mm
- Weight: 385g
- Compatible Models: Vehicle, Boat
- Transmit Power: <100mW
Receiver (Model: S10RX)
- Channels: 10CH+
- PWM Channel Number: 10
- Antenna: External single antenna
- Operating Voltage: 5-9V/DC
- Compatible Models: Vehicle, Boat
- Transmit Power: <100mW
Package Contents
Verify that all items are included in your package:
- S10 Transmitter x 1
- S10RX Receiver x 1
- Quick start guide x 1
- BVD wire x 1
- TypeC USB wire x 1
- Wrist strap x 1
- L-size silicone grip (pre-installed) x 1
- S-size silicone grip (pre-installed) x 1
- 18650 Lipo battery (pre-installed) x 1


Setup
Transmitter Overview and Functions

| No. | Function |
|---|---|
| 1 | Power button |
| 2 | Menu button |
| 3 | Scroll wheel / Confirm button |
| 4 | Back button |
| 5 | Trm1 ST DR |
| 6 | Trm2 TH Trm |
| 7 | Trm3 ST Trm |
| 8 | SW1 |
| 9 | SW2 |
| 10 | V1 |
| 11 | Trm5 |
| 12 | SW4 |
| 13 | SWB |
| 14 | SWD |
| 15 | Charging port |
| 16 | Flashlight |
| 17 | Lithium battery compartment |
| 18 | AAA battery compartment |
Note: The above button-to-channel mapping represents the transmitter's factory default configuration and can be customized in the "KEY" menu.
Transmitter Grip Customization

- Adjust Steering Wheel Tension: Rotate the adjustment wheel to set your preferred steering wheel tension.
- Trigger Lock Screw: Before adjusting the trigger position, loosen the trigger lock screw. After adjustment, tighten it securely.
Receiver Overview

The EXT port connects external devices for added functionality:
- GPS Module: Provides real-time position, speed, and heading data.
- Temperature Module: Monitors ESC and motor temperature.
Binding the Receiver
- Power on the receiver, press and hold its button for 3 seconds.
- Release the button once the blue LED starts fast blinking to enter binding mode.
- On the transmitter, navigate to the menu: Receiver -> Binding. Select "Standard Protocol" and press the "Bind" button.
- A solid blue LED indicates successful pairing.
Receiver Gyro Calibration
To ensure the accuracy of gyro data and attitude calculation, perform calibration after initial receiver installation or when vehicle attitude is abnormal.
- Ensure the transmitter and receiver are connected (the receiver's blue LED is steadily lit), and place the vehicle stationary on level ground.
- Navigate to Receiver -> GYRO FUNC and press "Gyro calibration".
- Confirm the vehicle is level in the pop-up, then press "Yes".
- The receiver LED will show a "three flashes, one pause" pattern. The screen prompts "Lift the front wheels". Lift the front wheels until the vehicle is upright.
- A "Calibration Successful" pop-up completes the process.
Battery Voltage Detection (BVD)
Connect the BVD cable to the receiver's BVD port, with the black wire to the battery balance lead's negative terminal and the white wire to its power terminal. Once the cable is powered on, the battery voltage will be displayed on the transmitter's main interface.
Operating Instructions
Transmitter Main Interface

- Quick Info Area: Scroll the wheel to switch between the following: 5 sets of quick information, Receiver voltage, ESC temperature, Effective signal strength, Acceleration, Real-time Vehicle Speed / Maximum Speed, Motor Temperature / ESC Temperature, and Lap Time Statistics.
- Channel & Basic Settings Quick Info Area: Displays real-time status of ST (Steering), TH (Throttle), and CH3-CH8. Shows TH TRM (Throttle Trim) and ST TRM (Steering Trim), Acceleration, DR (Steering Dual Rate), TR DR (Throttle Dual Rate), and BRAKE DR (Brake Dual Rate).
- Function Status Quick View Area: Displays the status of functions assigned to each switch. You can customize functions and corresponding display icons in the "KEY" menu.
Menu Navigation
The transmitter is equipped with a menu system for configuration. The menu has three levels: primary, secondary, and tertiary.
- On the transmitter's main interface, click the "Confirm" button to enter the Remote Control Setting Menu.
- Use the setting menu to navigate options.
- Click "Confirm" to proceed to the next level.
- Click the "Back" button to return to the previous menu level.
Fail-Safe Settings

- In the menu Receiver -> Fail-safe, configure independent fail-safe settings for each channel.
- If fail-safe is OFF for a channel: When the transmitter signal is lost, the channel output maintains its last valid state. If fail-safe is ON for a channel: When the signal is lost, the channel outputs the preset fail-safe value.
- To set fail-safe values:
- Select the target channel via the scroll wheel.
- Set the channel's fail-safe to OFF.
- Adjust the channel output to the desired fail-safe position.
- Click "Confirm" to enable fail-safe for that channel.
Flashlight Operation
Double-click the power button to toggle the flashlight on/off.
Remote Controller Firmware OTA Update
You can update the S10 transmitter's firmware over Wi-Fi in the System -> OTA menu.
Important: Ensure the transmitter's lithium battery has sufficient charge before starting the update. Do not power off the device during the process.
Receiver Firmware OTA Update
You can update the S10RX receiver's firmware over Wi-Fi in the Receiver -> Receiver Update menu.
Important: Ensure the receiver has a stable power supply throughout the entire update process. Do not disconnect power.
Maintenance
General Care
- Keep the transmitter and receiver clean and free from dust and dirt. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
- Store the device in a safe place when not in use to prevent damage.
Battery Care
- Always use the recommended battery types (18650 Lipo or AAA batteries).
- Do not overcharge or over-discharge batteries.
- Remove batteries if the device will not be used for an extended period.
Troubleshooting
Common Issues and Solutions
- No Power: Check battery installation and charge level. Ensure the power button is pressed correctly.
- No Signal/Binding Issues: Re-attempt the binding process as described in the Setup section. Ensure the receiver is powered and within range. Check for interference.
- Erratic Control: Perform receiver gyro calibration. Check for loose wiring or damaged components. Ensure the control range is not exceeded.
- Firmware Update Failure: Ensure the battery is fully charged and the power supply is stable during the update. Do not interrupt the process.
Safety Warnings and Important Notes

Operating RC models carries risk. You must read and follow all safety guidelines below to ensure everyone's safety.
Battery Charging and Power Safety
- [Warning] Charge on a fireproof surface under watch. Never overcharge or leave batteries unattended to prevent fire or explosion.
- [Important] The correct power on/power-off sequence is fundamental to safety: When turning on, power on the transmitter first, then the model. When turning off, power off the model first, then the transmitter. An incorrect sequence may cause the model to run out of control.
Environment and Location Inspection
- [Caution] Do not use in rain, snow, standing water, fog, thunderstorms, or other severe weather and low visibility conditions.
- [Warning] Stay away from power lines, high-voltage power lines, communication base stations, airports, and navigable waters. These locations pose extremely high interference risks and endanger public safety.
Mandatory Setup and Checks Before Use
- [Important] Always test range before first use, after location change, or with multiple devices to confirm control range and signal stability.
- [Mandatory] Correctly set the throttle channel fail-safe on the transmitter so the vehicle automatically brakes or idles if signal is lost.
- [Important] Before use, ensure model is secure and all servo directions match transmitter commands to prevent reverse control.
Core Operating Standards
- [Warning] Never hold or block the transmitter antenna. Always keep the model in clear sight to avoid signal blockage.
- [Caution] Maintain concentration, attention, and distance. Always check obstacles in the model's station and the surrounding environment. High-speed rotating propellers, wheels, and high-temperature motors pose serious injury risks.
Your Responsibility
- [Disclaimer] Remote control models are not toys. Improper operation may cause serious property damage and personal injury. You are responsible for reading the entire instruction manual and strictly complying with local laws and regulations to operate safely.
Disclaimer
Function Changes: The product software will be continuously updated. Functions, interfaces, and performance may be adjusted accordingly. The final right to interpret all changes belongs to Sense Innovations.
Safe Operation: Sense Innovations assumes no liability in safe, legal, and open areas. The company is not liable for any injury, damage, or legal disputes resulting from improper use, unauthorized modifications, or operation in hazardous locations (such as near roads, crowds, or bodies of water).
Compliance: Users are responsible for ensuring their use complies with local radio management, flight, and driving regulations of their country or region. All liability arising from non-compliance shall be borne solely by the user.
Data Accuracy: Sense Innovations provides data for reference only and shall not be liable for any indirect, incidental, special, or consequential damages (including but not limited to data loss, profit loss, business interruption) arising from the use of this product.
User Tips
- Always perform a range test before operating your RC model, especially in new environments or after making changes to your setup.
- Familiarize yourself with the fail-safe settings and ensure they are configured to safely stop your model in case of signal loss.
- Keep the firmware of both your transmitter and receiver updated to benefit from the latest features and improvements.
- For optimal control and safety, ensure your model's servos respond correctly to transmitter commands before each use.
Warranty and Support
For warranty information, technical support, or further assistance, please refer to the official SENSE Innovations website: www.sensehobby.com. This website provides the latest complete instructions, safety warnings, and software updates to ensure safe and compliant operation.