1. Product Overview
The Yieryi YG-9909 is a multi-functional water quality testing device designed for precise measurement of pH, Total Dissolved Solids (TDS), Electrical Conductivity (EC), Salinity, and Temperature. Its compact and waterproof design makes it suitable for a wide range of applications, including hydroponics, swimming pools, aquariums, and general water quality monitoring.
2. Key Features
- 5-in-1 Functionality: Measures pH, TDS, EC, Salinity, and Temperature.
- Backlit LCD Display: Ensures easy reading in dim light conditions.
- Automatic Temperature Compensation (ATC): Accurate readings across a temperature range of 0.1°C to 60.0°C.
- IP65 Waterproof Design: Provides protection against water splashes and dust.
- 135-Second Automatic Shut-Off: Conserves battery life.
- HOLD Function: Locks the current reading for convenient recording.
- Replaceable Glass Electrode: Extends the lifespan of the device.
- Low Battery Indicator: Alerts when battery replacement is needed.
3. Device Components
- Battery Case: Houses the LR44 batteries.
- LCD Backlight: Display screen for readings.
- ON/OFF Button: Powers the device on or off.
- HOLD Button: Freezes the current measurement on the display.
- MODE/CAL Button: Switches between measurement modes (pH, EC, TDS, Salinity) and initiates calibration.
- °C/°F Button: Switches temperature unit between Celsius and Fahrenheit.
- Upgraded Glass Electrodes: Sensing probes for water quality measurements.
4. Specifications
| Parameter | Range | Resolution | Accuracy |
|---|---|---|---|
| pH | 0.00-14.00pH | 0.01pH | ±0.05pH |
| TDS | 0-10000ppm, 10.1-200.0ppt | 1ppm; 0.1ppt | ±2%FS |
| EC | 0-10000μS/cm | 1μS/cm | ±2%FS |
| Salinity | 0%-20%, 0-10000ppm, 10.1-200.0ppt | 1ppm; 0.1ppt; 0.01% | ±2%FS |
| Temperature | 0.0°C-60.0°C (32.0°F-140.0°F) | 0.1°C/0.1°F | ±0.5°C |
Power Supply: 3*1.5V LR44 Batteries (Low Battery Indicator)
Dimensions: 183×42×42mm
Work Environment: Temperature 0.0°C-60.0°C (32.0°F-140.0°F); Relative Humidity 100%
5. Package Contents
- 1 × Yieryi YG-9909 5-In-1 Water Quality Tester
- 1 × User Manual
- 3 × 1.5V LR44 Batteries (Note: Batteries may not be included in some packages due to shipping restrictions, please check your specific order details.)
6. Setup
6.1 Battery Installation
- Locate the battery compartment at the top of the device (refer to Figure 2).
- Open the battery case.
- Insert three (3) LR44 1.5V coin cell batteries, ensuring correct polarity.
- Close the battery case securely.
6.2 Initial Preparation
- Remove the protective cap from the electrode.
- Rinse the electrode with distilled water before first use and after each measurement.
7. Operation
7.1 Power On/Off
- Press the "ON/OFF" button to turn the device on.
- Press the "ON/OFF" button again to turn the device off. The device also features a 135-second automatic shut-off to save power.
7.2 Mode Switching
- After powering on, press the "MODE/CAL" button to cycle through the measurement modes: pH, EC, TDS, and Salinity. The current mode will be displayed on the LCD.
7.3 Temperature Unit Switching
- Press the "°C/°F" button to switch the temperature display between Celsius (°C) and Fahrenheit (°F).
7.4 Taking Measurements
- Immerse the electrode into the solution to be tested. Ensure the electrode is fully submerged.
- Gently stir the solution and wait for the reading to stabilize on the LCD.
- The device will automatically compensate for temperature variations (ATC).
7.5 HOLD Function
- While taking a measurement, press the "HOLD" button to freeze the displayed reading.
- Press "HOLD" again to release the reading and resume live measurement.
8. Calibration
Regular calibration ensures the accuracy of your tester. The device is factory-calibrated, but recalibration is recommended for optimal performance, especially for pH.
8.1 pH Calibration
- Prepare pH buffer solutions (pH4.01, pH6.86, pH9.18). The device prioritizes pH6.86 for calibration.
- Turn on the tester and switch to pH mode.
- Immerse the electrode into the pH6.86 buffer solution.
- Long-press the "MODE/CAL" button for 3 seconds until the calibration mode is activated. The display will show "CAL" and then automatically recognize the buffer solution.
- Wait for the reading to stabilize and the calibration to complete (usually indicated by a stable reading or a "PASS" message).
- Rinse the electrode with distilled water and repeat the process for pH4.01 and pH9.18 solutions if higher accuracy is required across the full range.
8.2 TDS/EC/Salinity Calibration
- The TDS, EC, and Salinity functions are factory-calibrated with specific points (1413μS/cm EC, 1382ppm TDS, 35ppt Salinity).
- If recalibration is needed for these parameters, refer to the detailed instructions in the full user manual or contact customer support.
9. Maintenance
9.1 Electrode Cleaning and Storage
- Always rinse the electrode with distilled water before and after each use.
- Do not use tap water or deionized water for long-term storage, as this can damage the electrode.
- For long-term storage, keep the electrode moist by storing it in a small amount of pH storage solution or 3M KCl solution. If unavailable, use pH7 buffer solution.
- Replace the protective cap when not in use.
9.2 Electrode Replacement
The glass electrode is replaceable, extending the life of your tester. Refer to Video 1 for a visual guide.
- Ensure the device is powered off.
- Using a small screwdriver, carefully unscrew the four screws holding the electrode assembly in place.
- Remove the screw sleeve.
- Gently unplug the old electrode from the main unit.
- Align and plug in the new electrode.
- Reattach the screw sleeve and secure it with the four screws.
10. Troubleshooting
- Inaccurate Readings:
- Ensure the electrode is clean and free from debris.
- Perform a pH calibration as described in Section 8.1.
- Check battery level; replace if low.
- Ensure the electrode is fully submerged in the sample.
- No Display/Device Not Turning On:
- Check battery installation and polarity.
- Replace batteries if necessary.
- Slow Response Time:
- Clean the electrode thoroughly.
- Allow sufficient time for the reading to stabilize.
11. User Tips
- For Hydroponics and Pools: This tester is ideal for monitoring water quality in hydroponic systems to optimize plant growth and in swimming pools to maintain ideal pH (7.2-7.8) and salinity (2700-3400ppm) levels.
- Electrode Longevity: Proper cleaning and storage of the electrode are crucial for its lifespan and accuracy. Never let the electrode dry out.
- Calibration Powders: The device comes with pH calibration powders (pH4.00, pH6.86, pH9.18). Always use fresh distilled water to dissolve these powders for calibration.
12. Applications
The YG-9909 water quality tester is suitable for a wide range of applications, including but not limited to:
- Drinking water analysis
- Sewage treatment monitoring
- Water purification systems
- Fish tanks and aquariums
- Aquaculture
- Swimming pools and spas
- Hydroponic systems
- Medical care and laboratory use
13. Warranty & Support
The Yieryi YG-9909 Water Quality Tester typically comes with a 6-month warranty for non-human damage. For detailed warranty information, technical support, or service inquiries, please refer to the official Yieryi website or contact your retailer.