skydroid TR01

Contents

SKYDROID TR01 Dual Band Repeater

User Manual

Model: TR01 | Brand: SKYDROID

Safety Warnings and Disclaimer

Please read this entire manual carefully before operating the product. Failure to follow instructions may result in property damage, serious accidents, or personal injury.

  • Note: Failure to follow instructions may result in property damage and minor injuries.
  • Warning: Operate the product only after reading the entire user manual and becoming familiar with its functions. Improper operation may cause serious harm to yourself or others, as well as product damage and property loss.
  • This product is complex and requires familiarization for safe use. Basic common sense is also required.
  • This product is not suitable for children.
  • Do not use parts not provided or recommended by Skydroid. Strictly follow Skydroid's guidelines.

Operating Environment Requirements:

  • Ambient Temperature: -10°C to 60°C
  • Storage Temperature: -25°C to 60°C
  • Atmospheric Pressure: 86kPa to 106kPa
  • The place of use shall not have explosive hazardous media.
  • The surrounding media shall not contain gases or conductive media that corrode metals and damage insulation, and shall not be filled with water vapor or have severe mold growth.
  • The place of use shall be equipped with facilities to protect against rain, snow, wind, sand, and dust.

Disclaimer: The TR01 has completed debugging before leaving the factory. Do not disassemble or modify the TR01 yourself. Any unsafe or irresponsible operation may cause product damage, economic losses, or personal injury. The repeater can only be used for G-series links. Our company is not liable for direct or indirect losses or injuries caused by the use of this product.

1. Product Overview

The SKYDROID TR01 is a new generation dual-mode repeater for Unmanned Aerial Vehicles (UAVs), designed to meet increasing communication demands in complex environments. It leverages multi-protocol fusion technology to redefine UAV communication possibilities.

The system supports simultaneous coordination of 2.4GHz and 5.8GHz dual-frequency bands, ensuring Beyond-Visual-Line-Of-Sight (BVLOS) transmission. The TR01 can operate in either receiver mode or repeater mode for aerial relaying, allowing seamless switching in the air. This design effectively addresses coverage blind spots and anti-interference issues common in traditional single-mode repeaters.

Key Features:

  • Dual-band 2.4GHz/5.8GHz: Supports coordinated operation of both bands for signal stability and transmission efficiency, enhancing anti-interference capabilities.
  • Receiver/Repeater Dual Modes: Can function independently as a repeater or as a receiver to control unmanned devices. Simple, fast, and flexible mode switching adapts to various scenarios.
  • Strong Signal and Wide Coverage: Boasts strong anti-interference capability and wide-area signal coverage. In repeater mode, it can control unmanned devices at a distance of 10-20 km with stable connection and high-definition image transmission, overcoming large obstacles.
  • Easy to Operate: Works with the SKYDROID FLY GCS APP for quick switching of connection modes, eliminating tedious settings and making operation convenient and efficient.
  • Abundant Interfaces: Equipped with Ethernet ports, PWM output, data transmission interface, and SBUS output, adapting well to various unmanned devices.
SKYDROID TR01 Repeater with key features highlighted
Figure 1: SKYDROID TR01 Repeater highlighting its 2.4GHz/5.8GHz dual-band, receiver/repeater modes, strong signal, easy operation, and abundant interfaces.
Diagram showing receiver/repeater dual modes
Figure 2: Illustration of the TR01's Receiver/Repeater Dual Modes, showing its ability to connect a remote controller to a drone or act as a repeater for another device.
Diagram showing strong signal and wide coverage
Figure 3: Visual representation of the TR01's strong signal and wide coverage, demonstrating its capability to extend control range for drones.
Remote controller with SKYDROID FLY GCS APP interface
Figure 4: Remote controller displaying the SKYDROID FLY GCS APP interface, illustrating the ease of operation.
Diagram showing dual-band 2.4GHz/5.8GHz operation
Figure 5: Diagram illustrating the dual-band 2.4GHz/5.8GHz operation of the TR01, showing radio wave propagation.

2. Component Names and Interface Definition

The TR01 repeater features various components and interfaces for its operation. Familiarize yourself with the layout below.

Front view of SKYDROID TR01 Repeater with antennas
Figure 6: Front view of the SKYDROID TR01 Repeater with antennas.
Top view of SKYDROID TR01 Repeater with antennas
Figure 7: Top view of the SKYDROID TR01 Repeater with antennas.
Front view of SKYDROID TR01 Repeater without antennas
Figure 8: Front view of the SKYDROID TR01 Repeater without antennas, showing the TR01 logo and ventilation.
Back view of SKYDROID TR01 Repeater with antennas
Figure 9: Back view of the SKYDROID TR01 Repeater with antennas.
Bottom view of SKYDROID TR01 Repeater
Figure 10: Bottom view of the SKYDROID TR01 Repeater.
Side view of SKYDROID TR01 Repeater with ports
Figure 11: Side view of the SKYDROID TR01 Repeater, showing various ports.

Interface Definition:

Diagram of TR01 interfaces and pinouts
Figure 12: Detailed diagram of TR01 interfaces and pinouts.
No.AnnotationNo.Annotation
1Power Input Port (7.2V~72V)7Status Light & Frequency Pairing Expansion Port
2Data Transmission Port + SBUS Output8Ethernet Port 1
3PWM Output9Ethernet Port 2
4SMA Male Thread/Male Pin Antenna Port (2.4G/5.8G Dual-Band Antenna)10Frequency Pairing Button
5Receiver Frequency Pairing Indicator Light11Internal Screw Hole (Imperial Coarse Thread 1/4-20)
6Remote Controller Frequency Pairing Indicator Light

3. Setup and Installation Methods

The TR01 repeater is designed for two primary usage scenarios. Follow the recommended installation methods below.

3.1. Ground Repeater Mode

  1. Antenna Installation: Directly screw all antennas onto the SMA connectors of the repeater.
TR01 with antennas screwed on for ground repeater mode
Figure 13: TR01 with antennas installed for Ground Repeater Mode.
  1. Tripod Fixation: The bottom of the repeater has an Imperial coarse thread 1/4-20 screw hole, allowing it to be fixed to a tripod.
TR01 mounted on a tripod
Figure 14: TR01 mounted on a tripod for stable ground operation.

3.2. Aerial Repeater Mode

Warning: For aerial repeater mode, an extended feeder cable is required. The SMA connector must be fixed to the fuselage shell and the nut tightened to ensure a stable and reliable connection. Attach shock-absorbing foam to the bottom of the repeater for connection to the carrier, and install and tighten the antenna rod on the exterior of the fuselage.

Schematic diagram for Ground Repeater Application
Figure 15: Schematic Diagram for Ground Repeater Application, showing TR01 on a raised platform.
Schematic diagram for Aerial Repeater Application
Figure 16: Schematic Diagram for Aerial Repeater Application, showing TR01 mounted on a drone.

4. Operating the TR01 Repeater

4.1. Software Preparation

Before operating the TR01, ensure the necessary software is installed and updated:

  • Device Tool: Update to the latest version (rctool-3.0.5).
  • Skydroid FLY Software: Install the latest version on your remote controller.

Software download address: http://file.skydroid.xin/SkydroidFly.apk

4.2. Frequency Pairing Operation

  1. If you purchased a complete set of devices (remote controller, repeater, and GR01), they are pre-paired at the factory, and no additional pairing is required.
  2. Frequency Pairing Steps for Remote Controller, Receiver, and Repeater:
    Note: Do not pair multiple devices simultaneously. After successful pairing, if adding new devices, use the "Add Receiver" function for pairing.
    • Power on the repeater and wait 30 seconds. Press and hold the frequency pairing button until the Remote Controller Frequency Pairing Indicator Light (⑥) flashes rapidly, then release the button.
    • On the remote controller, go to [Device Tool] → [Frequency Matching] → click [Start Frequency Matching].
    Remote controller Device Tool Frequency Matching screen
    Figure 17: Remote controller screen showing the 'Device Tool' with 'Start Frequency Matching' button.
    • A pop-up window will appear asking whether to proceed with frequency pairing. Click [OK].
      Note: Frequency binding may cause the machine to stop working; operate under professional guidance.
    Frequency Matching confirmation pop-up
    Figure 18: Confirmation pop-up for Frequency Matching, warning about potential machine stoppage.
    • Wait for successful frequency pairing connection. A prompt indicating "START FREQUENCY MATCHING" will appear, and the pairing status will show "Connected".
    Device Tool screen showing 'Connected' status
    Figure 19: Device Tool screen indicating 'Connected' status after successful frequency pairing.
    • Power on the receiver. After powering on, the green light remains on, the blue light flashes intermittently, and the fan operates intermittently.
    • Press and hold the receiver's frequency pairing button until the blue light flashes rapidly, then release the button.
    • On the remote controller, go to [Device Tool] → [Frequency Matching] → click [Add Receiver].
    Device Tool screen with 'Add Receiver' button
    Figure 20: Device Tool screen with the 'Add Receiver' button highlighted.
    • A pop-up window will appear prompting "Add Receiver". Click [OK].
      Note: Please first put the receiver into the frequency alignment state and then click OK.
    Add Receiver confirmation pop-up
    Figure 21: Confirmation pop-up for 'Add Receiver', reminding to put the receiver in alignment state first.
    • Once the GR01 receiver successfully connects to the remote controller, the receiver's blue light will remain steadily on, and the repeater's Receiver Frequency Pairing Indicator Light (⑤) will also stay steadily blue.
      Note: The remote controller requires an internet connection. If a pop-up prompts you to open the Device Tool, ensure it is updated to the latest version.

    During frequency pairing, keep the remote controller, receiver, and repeater within 50 cm of each other.

4.3. Power-on Sequence for the Repeater and GR01 Receiver

After successful frequency pairing, power on the remote controller and let it enter the system. Then power off both the repeater and the GR01. It is mandatory to first power on the repeater, followed by the GR01. This ensures the remote controller connects to the repeater first, and then the repeater connects to the GR01.

Note: This power-on sequence must be strictly followed.

4.4. Switching Control Functions

When the remote controller is connected to the repeater and the repeater is connected to the GR01 (with the repeater and GR01 mounted on separate aircraft), the remote controller defaults to controlling the terminal aircraft connected to the GR01 (i.e., receiver mode).

  1. You can access [Device Tool] → [Video Viewing] (the page displays the receiver's image transmission feed, and both data transmission and SBUS can control the receiver).
  2. Click the repeater switch button.
Video viewing screen with repeater switch button
Figure 22: Video viewing screen on the remote controller, showing the repeater switch button.
  1. The current mode in use will be read automatically:
    • Repeater Mode: The remote controller connects to and controls the repeater device.
    • Receiver Mode: The remote controller connects to and controls the receiver via the repeater.
  2. Switch to Repeater Mode.
Mode selection screen (Receiver/Repeater)
Figure 23: Mode selection screen, allowing choice between Receiver and Repeater modes.
  1. Click [Save Settings]; a prompt indicating "Saving Successfully!" will appear.
'Saving Successfully!' prompt
Figure 24: 'Saving Successfully!' prompt after saving mode settings.
  1. Return to the video page, where the repeater's image transmission feed will be displayed. Both data transmission and SBUS can control the repeater device.

4.5. Repeater Baud Rate Settings

  1. Open [Device Tool] → [Advanced Options] → enter the password "999" → select [Set The Baud Rate].
Device Tool screen with 'Set The Baud Rate' option
Figure 25: Device Tool screen showing the 'Set The Baud Rate' option within Advanced Options.
  1. Repeater Serial Port: Click [Read Settings], then set the baud rate for the repeater serial port and save.
  2. Receiver Serial Port: Click [Read Settings], then set the baud rate for the receiver serial port and save.
    Note: Modifying the receiver serial port baud rate requires the receiver, repeater, and remote controller to be connected during configuration.
Baud rate selection for Repeater/Receiver serial port
Figure 26: Screen for selecting and saving baud rates for the Relay and Receiver serial ports.

4.6. Switching Between Repeater and Receiver Using FLY Ground Station

If you are using an S2 or S2mini flight controller or APM open-source flight controller, you can use the FLY ground station.

  1. Open Skydroid FLY and click the three horizontal lines in the top-left corner.
FLY Ground Station main menu
Figure 27: SKYDROID FLY Ground Station main menu with the three horizontal lines icon highlighted.
  1. Click [Switch Connection].
FLY Ground Station menu with 'Switch Connection' highlighted
Figure 28: SKYDROID FLY Ground Station menu with 'Switch Connection' option highlighted.
  1. Select the connection mode labeled with the repeater icon for the S2 + GR01 + G12/G20/C10 series, then click to enter.
FLY Ground Station connection method selection
Figure 29: FLY Ground Station screen for selecting the connection method, specifically the S2+GR01+G12/G20/C10 series with repeater icon.
  1. Introduction to the FLY Ground Station Homepage:
FLY Ground Station homepage overview
Figure 30: Overview of the FLY Ground Station homepage with various indicators and controls.
NO.AnnotationNO.Annotation
1Battery Voltage10Video Recording
2Flight Mode11Loudspeaker
3Signal Strength12Repeater Mode Switch Button
4Distance to HOME Point13Map
5Altitude14Attitude Sphere
6GPS Information15Horizontal Centering
7Remote Controller Battery Level16Global Centering
8Parameter Settings17One - key Descent
9Take Photo
  1. On the homepage, open the image transmission page. When the remote controller is connected to the repeater, which is then connected to the GR01 (controlling the aircraft with the terminal GR01), an icon of "repeater → drone" will be displayed on the left side.
Image transmission page with repeater to drone icon
Figure 31: Image transmission page showing the 'repeater to drone' icon on the left side.
  1. Click the repeater icon; options for connection modes will pop up, and a "Loading Successfully" prompt will appear at the bottom.
    • Receiver Mode: The remote controller connects to and controls the receiver via the repeater (default connection).
    • Repeater Mode: The remote controller connects to and controls the repeater device.
  2. Switching between the receiver and the repeater: Click [Connect to Repeater], then click [Confirm].
Connection mode options with 'Connect to Repeater' highlighted
Figure 32: Connection mode options with 'Connect to Repeater' highlighted for switching.
  1. The page will display a "Saving Successfully!" prompt.
  2. The icon on the left will change to the repeater icon, indicating that the switch has been successful and the repeater device is now controllable.
Image transmission page with repeater icon
Figure 33: Image transmission page showing the repeater icon on the left, indicating successful mode switch.

5. Maintenance: Repeater Firmware Update

Regular firmware updates ensure optimal performance and access to new features. Follow these steps to update your TR01 repeater's firmware.

  1. With the remote controller connected to the repeater, open [Device Tool] → [Advanced Options].
Device Tool screen with 'Advanced Options' highlighted
Figure 34: Device Tool screen with 'Advanced Options' highlighted.
  1. Enter the password "999" and confirm to enter the repeater firmware update mode.
Password entry for advanced options
Figure 35: Password entry screen for accessing advanced options, requiring '999'.
  1. Click [Update Device].
Device Tool screen with 'Update Device' highlighted
Figure 36: Device Tool screen with 'Update Device' button highlighted.
  1. Update the following firmware components:
    • Upgrade repeater SOC
    • Upgrade repeater AP side
    • Upgrade repeater DEV side
Firmware update options list
Figure 37: List of firmware components available for update, including repeater SOC, AP side, and DEV side.
  1. Upgrade Steps:
    • Check for updates.
    • Proceed with the update.
Firmware update progress screen
Figure 38: Firmware update screen showing current version and options to check and perform updates.

Note: Do not quit, disconnect, or power off during the update process.

6. Troubleshooting (FAQ)

Here are answers to some frequently asked questions regarding the TR01 Repeater.

  1. Can the repeater be paired with other Skydroid models or third-party remote controllers?
    Answer: The repeater can only be used with the Skydroid G-series links.
  2. Can additional devices (e.g., two receivers) be added to the repeater?
    Answer: No. The current supported configuration for the repeater is: 1 remote controller + 1 repeater + 1 receiver. Adding extra devices is not supported.
  3. Can the repeater double the communication distance?
    Answer: The main function of the repeater is to avoid obstructions. It can be mounted at an elevated position or installed on a drone to fly above obstacles.

7. Product Specifications

FeatureSpecificationFeatureSpecification
Operating Frequency2.4G/5.8GSerial Port Baud Rate57600/115200/921600
Power Supply Voltage7.2-72V(XT30)Operating Current560mA/12V
Data Transmission Port1 channelData RateFactory default: uplink 200kbps. Upload mode (optional) supports up to 1.2Mbps. Downlink: 10Mbps (max. 20Mbps with customization).
(Note: Enabling upload mode may reduce communication range; recommended for short-distance use.)
Ethernet Ports2 channelsDimensions248mm (length) × 140mm (width) × 20mm (height)
SBUS Output1 channelWeight191g
PWM Interfaces3 channelsOperating Temperature-10°C to 60°C
RF Power23dBm@CE/FCCChannel Bandwidth1.25MHz/2.5MHz/5MHz/10MHz/20MHz/40MHz
TR01 Specifications table
Figure 39: Detailed specifications table for the SKYDROID TR01 Repeater.

8. Warranty and Technical Support

8.1. After-Sales Service Terms

These terms apply only to products manufactured by Quanzhou Skydroid Technology Co., Ltd. Products sold by authorized Skydroid distributors are also subject to these terms.

  1. Quality Defects (within 1 week): If a non-human-induced quality defect is verified within one week from the date of purchase, Skydroid will bear the round-trip courier fees for repair.
  2. Quality Defects (1 week to 1 year): If a non-human-induced quality defect is verified between one week and one year from the date of purchase, the user and Skydroid will each bear the courier fee for sending the product for repair.
  3. Repair Documentation: When returning a product for repair, the purchase certificate, warranty card, or online platform transaction record must be provided.
  4. Free Replacement (within 7 days): If a non-human-induced quality defect occurs under normal use within seven days from purchase, and the product's appearance is undamaged, the user may negotiate with the distributor for a free replacement with the same model, provided the warranty card and purchase certificate are presented.
  5. Lifetime After-Sales Service: Skydroid products are provided with lifetime after-sales service. For non-human-induced quality defects, free warranty service is provided within one year from the date of purchase. For damages caused by human factors, modifications, disassembly, or products exceeding the one-year free warranty period, the user shall bear the round-trip courier fees and repair costs.
  6. Protecting Your Rights: To ensure your rights and interests are protected and to receive timely and effective service, fully fill out the warranty card and request a purchase certificate when purchasing a Skydroid product. The user must present the warranty card and purchase certificate to enjoy the benefits.
  7. Repair Turnaround: Repaired products will be sent back to the customer within 15 working days after Skydroid receives the defective product, accompanied by a repair report.
  8. Regional Scope: The above after-sales service terms apply only to Skydroid products sold in Mainland China.

8.2. After-Sales Address & Technical Support

After-Sales or Return/Exchange Address: 2nd Floor, Building A, Incubation Base, Fengze Technology Road, Quanzhou City, Fujian Province

Recipient: Mr. Wang

Contact Number: 18876386351

After-Sales Service Process: When sending the product back for after-sales service, please enclose a note stating your contact details, return address for the repaired product, and reason for sending the product back. No processing will be done if this information is missing.

Return/Exchange Process: When sending the product back for return/exchange, please enclose a note stating your contact details, return address, and reason for return. Retain the outbound order and original packaging. Losses due to unspecified return reasons will be borne by the sender. Cash on delivery is not accepted.

Any updates to this manual will take effect without prior notice. Please continue to follow the official website at www.skydroid.xin for the latest information.

User Manual (PDF) available for download: SKYDROID TR01 User Manual PDF

9. User Tips

No specific user tips were available from provided reviews or Q&A. Always refer to the official documentation and community forums for best practices and additional advice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.