Varstrom DPC080.C

Contents

BAFANG DPC080 Ebike Display Instruction Manual

Model: DPC080.C | Brand: Varstrom

1. Introduction

The Varstrom BAFANG DPC080 Ebike Display is a compact and intelligent CAN Bus display designed to provide essential riding data and advanced customization options for your e-bike. This manual will guide you through the installation, operation, and maintenance of your DPC080 display to ensure optimal performance and an enhanced riding experience. The DPC080 is co-engineered by Varstrom and Bafang, integrating core riding data, deep customization, and smart connectivity into a compact form, offering professional control for urban commuting and leisure riding.

BAFANG DPC080 Ebike Display showing speed, battery, trip, and range.
Figure 1: BAFANG DPC080 Ebike Display overview.

2. Setup and Installation

2.1 Unpacking and Inspection

Carefully unpack the DPC080 display and inspect for any signs of damage. Ensure all components are present.

2.2 Handlebar Installation

The DPC080 display features a one-piece design that fits standard 22.2mm handlebars. Position the display on your handlebar for optimal visibility and access to buttons. Secure it firmly using the integrated mount.

BAFANG DPC080 display mounted on a bicycle handlebar, showing its compact size and 22.2mm holder.
Figure 2: DPC080 display mounted on a handlebar (22.2mm holder size).

2.3 Wiring Connection

The DPC080 display uses a Male 5-PIN CAN protocol connector. Ensure your e-bike's wiring harness is compatible. Refer to the wiring diagram below for correct connections.

Wiring diagram for BAFANG DPC080 display showing female 5 pins (EB1T4 Connector) and male 5 pins (Display Connector) with color-coded wires: Green CAN H, Black GND, Brown P+, Orange Key Signal, White CAN L.
Figure 3: Cable Parameters and Wiring Diagram. The diagram shows the female 5-pin EB1T4 connector and the male 5-pin display connector. Wires are color-coded: Green for CAN H, Black for GND, Brown for P+, Orange for Key Signal, and White for CAN L. Confirm your motor's wiring diagram matches to ensure proper function.

Important:

If the wiring diagram of your motor is different, the display will not work. Please confirm compatibility with your motor's seller.

2.4 Initial Power On

Once installed and connected, power on your e-bike. The display should light up and show initial information. If not, check all connections and the e-bike's battery status.

3. Operating Instructions

3.1 Display Overview

The 1.9-inch TFT color screen provides real-time information at a glance. Key indicators include:

  • Battery level graphic
  • Headlight display
  • Real-time speed (km/h or mph)
  • Power indication bar
  • Single trip distance
  • Gear display (PAS level)
  • Range (estimated remaining distance)
  • Total mileage
Detailed view of the DPC080.C Digital Display showing various indicators like battery level, headlight, real-time speed, power, single trip, gear, range, and total mileage. Also shows the Type-C charger port and BAFANG GO+ app integration.
Figure 4: DPC080.C Digital Display interface and features.

3.2 Button Functions

The display features intuitive buttons for control:

  • Power Button: Turns the display on/off.
  • '+' Button: Increases assist level.
  • '-' Button: Decreases assist level.
  • Long Press '+' Button: Toggles the headlight on/off.
  • Long Press '-' Button: Activates Walk Assist mode (6 km/h boost).
  • Press and Hold '+' and '-' Buttons Simultaneously: Enters the settings menu.

3.3 BAFANG GO+ App Integration

The DPC080 display supports Bluetooth connectivity for integration with the BAFANG GO+ app. This app allows for advanced customization and data analysis.

Smartphone screen showing the BAFANG GO+ app interface with settings for support level, vehicle information, and system settings. The app also displays real-time speed, battery, trip, and average speed.
Figure 5: BAFANG GO+ App interface for customizing motor settings and viewing ride data.

App Features:

  • Motor Settings Customization: Adjust acceleration, start-up angle, and speed/current limits per assist level.
  • Ride Analytics: View detailed ride data, including speed, distance, and calories burned.
  • Navigation Integration: The app can provide map navigation directly on the display (for compatible models/features).
  • OTA Wireless Updates: Keep your display, controller, and sensors updated with the latest firmware.

Search for "BAFANG GO+" in your app store (Apple App Store or Google Play Store) to download and install the application.

3.4 Advanced Settings

To access advanced settings, press and hold the '+' and '-' buttons simultaneously. An advanced settings password (default: 1919) may be required. Within these settings, you can configure:

  • Speed Limits: Set desired maximum speed (1-99 km/h).
  • PAS Levels: Choose between 0-3 or 0-5 assist levels.
  • Wheel Size: Configure the correct wheel size for accurate speed and distance readings.
  • Display & Power:
    • Dual UI themes.
    • Backlight brightness (25%-100%).
    • Auto-off timer (1-10 minutes).
    • Ambient light sensing for automatic backlight adjustment.
  • Language: Select from English, German, Dutch, French, Italian, and Czech.

4. Maintenance and Care

4.1 Cleaning

Wipe the display screen and body with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the screen or housing.

4.2 Waterproofing

The display is IPX7 waterproof, meaning it can withstand temporary immersion. However, avoid prolonged submersion or high-pressure water jets directly on the display to prevent potential damage.

4.3 Software Updates

Regularly check for and install software updates via the BAFANG GO+ app to ensure optimal performance and access to new features.

4.4 Storage

When not in use for extended periods, store the e-bike and display in a dry, cool place. The recommended storage humidity is 30%-70%.

5. Troubleshooting

This section addresses common issues you might encounter with your DPC080 display.

  • Display does not power on:
    • Check all cable connections, especially the main power cable to the display.
    • Ensure the e-bike battery is charged and powered on.
    • Verify the display is compatible with your e-bike's voltage (36V/48V/52V).
  • Incorrect speed or distance readings:
    • Check the wheel size setting in the advanced settings menu via the display or BAFANG GO+ app.
    • Ensure the speed sensor is correctly installed and functioning.
  • Bluetooth connectivity issues:
    • Ensure Bluetooth is enabled on your smartphone and the display.
    • Make sure the BAFANG GO+ app is installed and updated.
    • Try restarting both the display and your smartphone.
  • Display shows an error code:
    • Consult the BAFANG GO+ app or your e-bike's main controller manual for specific error code interpretations.
    • If the issue persists, contact customer support.

6. Specifications

FeatureSpecification
ModelDP C080.C
TypeDisplay
ConnectorMale 5 PIN (CAN Protocol)
Screen1.9" TFT IPS Screen
Voltage Compatibility36V/48V/52V
PAS Levels5 (Configurable 0-3 or 0-5)
Speed Limit1km/h ~ 99km/h (Adjustable)
Brightness25% 50% 75% 100% (with ambient light sensing)
Button Holder DiameterØ22.2mm
Charge PortType-C
Waterproof RatingIPX7
Storage Humidity30%-70%
Operating Temperature-20°C ~ 45°C
Storage Temperature-20°C ~ 60°C
Auto OFFOFF, 1~10min Optional
Advanced Setting Password1919 (Customizable)
Bluetooth FunctionYes
Languages Supported6 (English, German, Dutch, French, Italian, Czech)
Dimensions (approx.)74.4mm (L) x 46.7mm (W) x 50.7mm (H)
Cable Length300mm (11.8")
Product specification diagram showing dimensions of the DPC080 display: 74.4mm (2.94 inches) length, 46.7mm (1.84 inches) width, 50.7mm (2 inches) height, 22.2mm (0.87 inches) handlebar diameter, and 300mm (11.8 inches) cable length. A table below lists detailed specifications.
Figure 6: Detailed product dimensions and specifications.

7. Warranty and Support

7.1 Warranty Information

Varstrom provides the following warranty for the DPC080 Ebike Display:

  • Display Unit: 1 Year Warranty.
  • Motor & Battery: 12 months quality warranty.
  • Accessories & Parts: 30-day warranty for quality assurance.

Under Warranty:

  • If a quality problem occurs within 6 months (based on Delivery Date), all warranty costs (repair cost, material cost, shipping cost, etc.) are covered by the seller.
  • If a quality problem occurs more than 6 months but not more than 12 months, the repair cost and material cost are covered by the seller, but the shipping cost is the buyer's responsibility.

Out of Warranty:

If the warranty period is exceeded, after-sales service can still be provided, but the cost will be the buyer's responsibility. The exact cost depends on the specific issue.

Warranty Service table showing warranty periods: E-Bike Frame 24 Months, Motor & Battery 12 Months, Parts & Accessories 1 Month. Details on 'Under Warranty' and 'Out of Warranty' conditions are provided.
Figure 7: Warranty Service details.

7.2 Support

For any questions or issues, please contact Varstrom E-Bike Global Store customer service. They offer local expertise with certified service centers in the USA, UK, and Poland.

8. User Tips

  • App Customization: Take advantage of the BAFANG GO+ app to fine-tune your motor settings (acceleration, speed limits) to match your riding style and local regulations.
  • Password Protection: Utilize the advanced settings password (default 1919) to prevent unauthorized changes to your display settings. Remember to change it to a unique password for better security.
  • Regular Checks: Periodically check cable connections for tightness and wear, especially after riding on rough terrain, to ensure consistent performance.
  • Type-C Charging: The integrated Type-C port can be used for charging small devices, adding convenience during your rides.
  • Automatic Backlight: The display features automatic backlight adjustment based on ambient light, ensuring readability in various conditions.

9. Video Demonstration

Watch this video for a visual guide on customizing motor settings and map navigation integration with BAFANG displays, including the DPC080.

Video 1: BAFANG DPC080 Display - Customizing Motor Settings and Map Navigation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.