Heimerdinger LB328BODY

Contents

Heimerdinger 18V Strapping Machine User Manual

Model: LB328BODY

Brand: Heimerdinger

1. Introduction

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Heimerdinger 18V Strapping Machine. Please read this manual thoroughly before using the machine and keep it for future reference.

Heimerdinger 18V Strapping Machine

Figure 1: Heimerdinger 18V Strapping Machine (overall view)

2. Safety Instructions

Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.

  • Read all instructions before operating the machine.
  • Keep work area clean and well-lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
  • Use appropriate personal protective equipment (PPE) such as safety glasses, gloves, and hearing protection.
  • Ensure the strapping machine is switched off and the battery is removed before making any adjustments, changing accessories, or storing the tool.
  • Use only the specified strapping materials (PP/PET) and sizes (13-16mm width, 0.4-1.2mm thickness).
  • Do not overreach. Keep proper footing and balance at all times.
  • Do not use the machine if the switch does not turn it on and off.
  • Maintain tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation.
  • Store idle tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

3. Product Overview

3.1 Components and Controls

Labeled components of the strapping machine

Figure 2: Key Components of the Strapping Machine

  • Tightening Button: Engages the tensioning mechanism.
  • Fusion Button: Initiates the friction heat welding process.
  • LED Display Screen: Shows current settings and battery status.
  • Limit Plate: Guides the strapping tape into position.
  • Welding Sheet: Area where the tape ends are fused.
  • Clamping Handle: Used to open the tape path for insertion.
  • Lithium Battery: Provides power to the machine (not included with "No battery" option).
Digital display and control buttons

Figure 3: Digital Display and Control Panel

  • Indicator Light: Shows operational status.
  • Battery Power Indicator: Displays remaining battery charge.
  • LED Display: Numeric display for settings.
  • Function Button (P/SET): Used to enter setting mode and confirm selections.
  • Increment Button (INC): Increases the value of a setting.
  • Decrement Button (DEC): Decreases the value of a setting.

4. Specifications

Specifications for the strapping machine

Figure 4: Key Specifications

FeatureDetail
Model NumberLB328BODY
Voltage18-21V
Sealing MethodFriction Heat Welding
Welding Time0.5 - 5 seconds
Maximum Tightening Force3500N
Power500W
Applicable Packing TapePP/PET
Packing Tape Size (Width)13 - 16mm
Packing Tape Thickness0.4 - 1.2mm

5. Setup

5.1 Battery Installation

This machine is compatible with Makita 18V B series lithium batteries (e.g., BL1850B, BL1840B, BL1830B, BL1430B, BL1820B, BL1850, BL1840, BL1440, BL1415, BL1815N). It is NOT compatible with G Series batteries (e.g., BL1813G) or 18V Ni-CD batteries (e.g., 1822).

  1. Ensure the machine is switched off.
  2. Align the battery with the battery slot on the machine.
  3. Slide the battery into the slot until it clicks securely into place.
  4. To remove, press the battery release button and slide the battery out.
Strapping machine without battery

Figure 5: Strapping Machine (battery not included)

5.2 Loading Strapping Tape

  1. Ensure the machine is switched off and the battery is removed.
  2. Press the clamping handle to open the tape path.
  3. Insert the appropriate PP/PET strapping tape (13-16mm width, 0.4-1.2mm thickness) into the tape path, ensuring it passes under the welding sheet and limit plate.
  4. Release the clamping handle to secure the tape.

6. Operating Instructions

Watch the product demonstration video for a visual guide on operation:

Video 1: Heimerdinger Strapping Machine Demonstration

6.1 Powering On and Adjusting Settings

  1. Insert a charged battery.
  2. Press the power button (if available, otherwise the machine powers on with battery insertion).
  3. Use the P/SET button to cycle through adjustable parameters (e.g., tension force, welding time).
  4. Use the INC and DEC buttons to adjust the values displayed on the LED screen.
  5. Press P/SET again to confirm the setting and move to the next parameter, or to exit setting mode.

6.2 Strapping Process

  1. Place the strapping tape around the item to be bundled.
  2. Overlap the two ends of the tape.
  3. Insert the overlapped tape ends into the machine's tape path, ensuring the bottom tape is under the welding sheet and the top tape is above it, guided by the limit plate.
  4. Press and hold the Tightening Button to tension the strap. Release when desired tension is achieved.
  5. Press the Fusion Button (one-button welding) to initiate the friction heat welding process. The machine will automatically weld and cut the strap.
  6. Once the welding is complete, carefully remove the machine from the strapped item.
Fusion welding with one button

Figure 6: One-Button Fusion Welding in Action

Examples of items strapped with the machine

Figure 7: Applications of the Strapping Machine

7. Maintenance

  • Cleaning: Regularly clean the machine, especially the tape path and welding sheet, to prevent accumulation of dust and debris. Use a dry cloth; do not use solvents.
  • Inspection: Periodically check for any loose screws, damaged parts, or excessive wear. Replace worn parts immediately.
  • Storage: Store the machine in a dry, clean, and secure location, out of reach of children, when not in use. Remove the battery before long-term storage.
  • Battery Care: Follow the manufacturer's instructions for charging and storing batteries.

8. Troubleshooting

ProblemPossible CauseSolution
Machine does not power onBattery not inserted correctly or discharged.Ensure battery is fully charged and properly inserted.
Poor welding qualityIncorrect welding time setting; dirty welding sheet; incorrect tape type/thickness.Adjust welding time (0.5-5s); clean welding sheet; ensure correct PP/PET tape (0.4-1.2mm thickness).
Tape not tensioning properlyIncorrect tension setting; tape not loaded correctly; worn tensioning mechanism.Adjust tension force (max 3500N); re-load tape correctly; inspect for wear.
Tape jamsIncorrect tape size; debris in tape path.Use correct tape width (13-16mm); clean tape path.

9. User Tips

  • For optimal performance, ensure your battery is fully charged before starting a large strapping job.
  • Experiment with different tension and welding time settings on scrap material to find the ideal configuration for your specific strapping tape and package type.
  • Always keep spare strapping tape on hand to avoid interruptions during work.
  • When strapping delicate items, consider using corner protectors to prevent the strap from damaging the edges.

10. Warranty & Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the Heimerdinger Official Store. Keep your purchase receipt as proof of purchase.

© 2023 Heimerdinger. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.