ETENWOLF S1

Contents

ETENWOLF S1 Portable Tire Inflator

User Manual

Model: S1

Introduction

The ETENWOLF S1 is a compact, lithium-powered portable tire inflator designed for passenger cars, SUVs, crossovers, motorcycles, bicycles, and sports balls. It features a powerful built-in 5200mAh (2600mAh*2) lithium battery, delivering high-speed inflation of 20L/M at 0 PSI (0.65 CFM at 0 PSI) and reaching a maximum pressure of 160 PSI (11.0 bar). With a 100% duty cycle, this inflator can operate continuously without requiring cool-down breaks. It recharges conveniently via a universal USB-C port, supporting 10W PD fast charging. The integrated air hose storage ensures a truly portable, all-in-one design, eliminating the need to carry a separate hose. An additional built-in work light enhances usability in low-light conditions.

Video: Demonstrating the ETENWOLF S1 Portable Tire Inflator's compact size, ease of use, and versatility for various inflation needs.

Package Contents

Ensure all the following items are included in your package:

  • S1 Multi-Function Tire Inflator x1
  • A-C charging cable x1
  • T-shaped quick connector x1
  • French copper adapter x1
  • Ball needle x1
  • Storage Bag x1
  • Instruction manual x1
Contents of the ETENWOLF S1 package including the inflator, charging cable, various adapters, storage bag, and manual.
Image: All items included in the ETENWOLF S1 Portable Tire Inflator package.

Product Overview

Familiarize yourself with the components and controls of your ETENWOLF S1 Portable Tire Inflator:

Front view of the ETENWOLF S1 tire inflator showing the digital display and control buttons.
Image: Front view of the inflator with digital display and control panel.
Side view of the ETENWOLF S1 tire inflator showing the integrated high-pressure hose storage.
Image: Side view illustrating the integrated high-pressure hose storage.

Controls and Display

  • '+' Button (Pressure Increase): Increases target pressure.
  • '-' Button (Pressure Decrease): Decreases target pressure.
  • Start/Pause Power Button: Long press to turn on/off, short press to start/pause inflation.
  • Light Button: Activates and cycles through LED light modes.
  • Mode Button: Short press to switch between inflation modes (Manual, Car, Bicycle, Ball). Long press to switch pressure units (PSI, KPA, Bar).
  • Digital Display: Shows target pressure (smaller numbers at top) and actual pressure (larger numbers at bottom).
  • Pressure Unit Indicator: Displays current unit (PSI, KPA, Bar).
  • Battery Level Indicator: Shows remaining battery capacity.
  • Safety Warning Icon: Alerts to abnormal conditions.
  • Progress Bar: Indicates inflation progress.
  • High-Pressure Hose: Connects to the tire valve.
  • Type-C Port: For charging the device.
  • LED Light: Provides illumination.

Setup and Basic Operation

Follow these steps for quick and efficient tire inflation:

  1. Connect & Power On: Press the power button for 0.5 seconds to turn on the device. Take out the high-pressure hose from its storage compartment. Attach the hose nozzle clockwise into the object to be inflated.
  2. Set Mode & Unit: Short press the Mode button to switch between the four preset modes: Manual Mode, Car Mode, Bicycle Mode, and Ball Mode. Long press the Mode button to switch the pressure unit between PSI, KPA, and Bar.
  3. Set Target Pressure: Use the '+' and '-' buttons to adjust your desired target pressure. The smaller numbers on the display indicate the target value, while the larger numbers show the actual pressure.
  4. Start Inflating: Press the power button again to start the inflation process.
  5. Auto Stop: The inflator will automatically stop once the preset target pressure is reached.
Four-step visual guide for using the ETENWOLF S1: Connect & Power On, Set Mode & Unit, Start Inflating, Auto Stop.
Image: Visual guide for the 4-step inflation process.

Inflation Modes and Ranges

ModeAdjustable Pressure Range
Manual Mode3.0-160.0 PSI
Car Mode8.0-130.0 PSI
Bicycle Mode10.0-145.0 PSI
Ball Mode3.0-16.0 PSI
Diagram showing four inflation modes: Bicycle, Ball, Car, and Custom, with default PSI values and typical inflation times.
Image: Overview of the four inflation modes with default settings and typical inflation times.

Memory Pressure Setting

The ETENWOLF inflator remembers your last target pressure value and unit option. This allows you to change the default pressure at any time, and the device will retain your preferred settings for convenience.

Automatic Shut-off Conditions

The inflator will automatically shut off in the following cases:

  • When the charging cable is disconnected during charging.
  • When the battery is depleted.
  • 5 minutes after being fully charged.
  • 3 minutes after standby.
  • If inflation exceeds 5 minutes and the actual pressure value is still below 5 PSI or above 150 PSI.

LED Light Operation

The LED light is located at the top of the inflator. After powering on, short press the light button to turn it on.

Lighting Modes

The LED light offers three different modes:

  • High Beam: Standard bright illumination.
  • Flashing Mode: For signaling or increased visibility.
  • SOS Signal: For emergency situations.
Image showing the ETENWOLF S1 inflator's LED light illuminating an engine bay, with text indicating Illumination Light, Slow-Speed Strobe Light, and SOS Light modes.
Image: Demonstrating the LED Strong Lighting feature with Illumination, Strobe, and SOS modes.

Note on Auto Shut-off

After working for one hour, the light will flash as a reminder. At this time, press the light button to cancel the auto shut-off, and the light will stay on until the power runs out or it is turned off manually. If no operation is performed, it will flash and then turn off.

Battery Management

Charging

For optimal charging performance and stability, please use a certified PD charger and the supplied charging cable to charge the built-in battery. It takes approximately 2–3 hours to fully charge the inflator from 0% to 100%.

Before first use, fully charge the inflator completely. Use the charging cable to connect it to a certified PD charger.

Battery Level Indicator

The battery level indicator on the display is divided into four bars, each representing 25% capacity:

  • [----]: 0-25%
  • [■---]: 25%-50%
  • [■■--]: 50%-75%
  • [■■■-]: 75%-100%

Note: When the battery level drops below 10%, the battery indicator will flash.

Remark: The inflator will automatically shut off if inactive for 5 minutes after being fully charged. The inflator cannot be used while charging.

Pressure Calibration

Different altitudes may cause a pressure variation of 1-3 PSI. When in high-altitude areas (especially above 5000 ft / 1524 m), users can recalibrate the pump's pressure sensor.

Calibration Steps

  1. Press the power button to turn on.
  2. Press and hold the light button ('*') and the mode button ('C') simultaneously for 10 seconds.
  3. The screen will restart, and the pump will be successfully recalibrated.

Important Notes for Calibration

  • Turn on the device before starting calibration.
  • The high-pressure hose must not be connected to anything. Any pressure applied to the hose will invalidate the recalibration process.
  • Battery power or another power source is required for recalibration.
  • There is no memory for new calibration settings. Once the power is turned off, it will reset to sea-level calibration (0 ft / m).
  • In high-altitude areas above 5000 ft / 1524 m, manual calibration is required each time the pump is turned on.

Maintenance

  • Store the product within -4°F~140°F / -20°C~60°C. Extreme heat or cold may damage the battery and shorten its lifespan.
  • Charge the inflator at least once every three months to maintain good performance.
  • Keep the product away from heat sources and do not leave it inside a hot car for long periods, as overheating may cause it to explode.
  • Use this product in a dry and clean environment. Dust and sand intrusion may damage the product. Do not clean the product with water.

Troubleshooting

ProblemSolution
Inflation speed is slowCheck if the inflation hose is damaged and ensure the battery is sufficiently charged.
Pump turns on but does not inflateCheck if the pressure of the object exceeds the preset pressure.
Battery indicator does not appear after chargingUse a certified PD charger and cable, then try charging again.
Pump stops working due to extreme temperature conditionsDuring charging, ensure the pump operates within 0°C / 32°F ~ 45°C / 113°F. During inflation or deflation, ensure the pump operates within -20°C / -4°F ~ 74°C / 165°F.
Safety warning icon lights up when abnormal pressure or motor response is detectedTurn off the machine, wait 10 minutes, then restart.
Pump is inflating but the display shows zero pressureIf the air pressure is below 3 PSI, the display will show zero due to the pump's minimum detection range.
Battery level indicator differs during inflation compared to standbyThe lithium battery voltage drops significantly during discharge, causing the battery indicator to display differently during inflation than in standby. This is normal.
Safety warning icon shows E08If the issue persists after turning off and restarting, send the device to the factory for repair.
Display E10 Error CodeThis indicates a motor fault warning, and the motor stops working. After flashing for 30 seconds, it should recover. If the problem persists after restarting, send the device to repair.
Display E11 Error CodeLow-temperature charging protection icon indicates the temperature is too low during charging. Before continuing, restore the temperature to above 0°C.
Display E12 Error CodeHigh-temperature charging protection icon indicates the temperature is too high during charging. Before continuing, restore the temperature to below 45°C.
Display E13 Error CodeLow-temperature discharge protection icon indicates the temperature is too low during inflation. Before continuing, restore the temperature to above -20°C.
Display E14 Error CodeHigh-temperature discharge protection icon indicates the temperature is too high during inflation. Before continuing, restore the temperature to below 58°C.
Display E15 Error CodePump has exceeded working time. The warning icon will flash for 30 seconds before returning to normal. Check the object for leaks.
Display E16 Error CodeOverpressure protection icon. Normal operation resumes after pressure release.
Display E17 Error CodeHigh-pressure operation exceeded working time. The warning icon will flash for 30 seconds before returning to normal. Check if the inflated component is functioning abnormally.
Display E18 Error CodeBattery damage warning icon and battery indicator light. After flashing for 30 seconds, the device will shut down. The device must be sent to the factory.
Display E22 Error CodePreset value is lower than the actual air pressure value.

Specifications

AttributeValue
NamePortable Tire Inflator
ModelS1
Dimensions169.2 x 53.4 × 67 mm (6.66 x 2.10 x 2.64 inches)
Inflation Pressure Range3.0-160.0 PSI / 0.20-11.00 bar
Operating Temperature (Charging)32°F–113°F / 0°C-45°C
Operating Temperature (Discharging)-4°F~165°F / -20°C~74°C
Storage Temperature-4°F~140°F / -20°C~60°C
High-Pressure Hose Length355 mm
Battery Capacity5200 mAh (19.2 Wh)
Operating NoiseBelow 85 dB within 1 meter
InputType-C: 5V 2A
Working TimeApproximately 20 minutes at 25°C ambient temperature, within 20–50 PSI inflation pressure range
Charging Time2-3 hours
Sensor Accuracy±1 PSI
Item Weight0.61kg
Item Height6.97inch
Item Width2.4inch
Item Length3.74inch

Safety Instructions

Please read all safety warnings and instructions carefully to reduce the risk of electric shock, fire, and/or serious injury.

  • This product is not a toy and should not be used by children. Users must be at least 16 years old. Keep children at a safe distance during inflation.
  • The product contains a built-in lithium battery. Do not throw the battery or place the product in fire.
  • Overheating or water damage may increase the risk of fire or explosion. Keep the product away from heat sources and do not leave it inside a hot car for long periods. If the pump becomes very hot, it may explode.
  • This product contains a DC motor that may generate sparks during use. Do not use it in dusty or explosive gas environments.
  • If unusual noise occurs or the pump becomes excessively hot during inflation, turn it off immediately.
  • Ensure the correct pressure unit is selected before setting the inflation pressure. Mixing PSI and bar may cause overinflation and explosion. (Conversion: 1 bar = 14.5 PSI, 1 bar = 100 kPa).
  • Do not leave the pump unattended while it is operating.
  • Always use a certified PD charger and the supplied charging cable to charge this product.
  • To reduce the risk of electric shock, do not expose the product to rain and store it indoors.
Diagram illustrating the Multi-Shield Protection System of the ETENWOLF S1, including Motor Protection, Low/High-Temp Charging/Discharge Protection, Overvoltage Protection, Cell Protection, and High-Voltage Protection.
Image: Multi-Shield Protection System for safe operation.

User Tips

  • The rotating hose and its integrated storage compartment are a clever design feature, making the device very portable and convenient.
  • The bright display and useful presets simplify operation, allowing for quick setup and inflation.
  • The built-in LED light is a valuable addition, especially for night repairs or in low-light conditions.
  • The altitude adjustment feature ensures accurate pressure readings regardless of your location.
  • The device is rechargeable, allowing you to set the desired pressure and inflate tires without external power sources.
  • It can inflate a bike tire from 35 to 55.2 PSI in approximately 60 seconds, demonstrating its efficiency.

Warranty and Support

Within two years of purchase, ETENWOLF provides prompt and effective online after-sales service. We will repair or replace any defective product (caused by manufacturing faults) within the warranty period.

Malfunctions caused by failure to comply with the instructions and safety warnings in this manual are not covered by the warranty.

Contact Information

If you have questions or comments, please contact us:

Manufacturer Details

Manufacturer: Guangdong Bestek Technology Co., Ltd
Address: No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R.China

Brand Owner: Mozhen Technology (Shenzhen) Co., LTD
Address: CN-503, Floor 5, Building 4, Tianan Yungu Industrial Park Phase II, Gangtou Community, Bantian Street, Longgang District, Shenzhen, Guangdong, CN

Made in P.R.C

© 2024 ETENWOLF. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.