Godox SK400II

Contents

Godox SK400II Compact Studio Flash Instruction Manual

Model: SK400II

Brand: Godox

1. Introduction

Thank you for purchasing the Godox SKIIIV series compact studio flash. This series is specifically designed for portrait and e-commerce product photography in shooting studios and photography workshops. It features power adjustment, photocell triggering, modeling lamp, and more. It can also provide high light, background light, or hair light in large studios.

2. Important Safety Instructions

This product is professional photographic equipment, to be operated by professional personnel only. All transport protective materials and packaging on the product must be removed before use.

The following basic safety precautions must be followed when using this product:

  1. Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in death, serious injury, damage to the product, or other property damage.
  2. This device must be connected to a grounded outlet.
  3. High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after power off.
  4. This product is a professional lighting fixture, children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.
  5. This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
  6. This fixture emits high-intensity, high-frequency stroboscopic light. Individuals with a history of photosensitive epilepsy or sensitivity to intense light must not use or approach it.
  7. Extreme caution must be exercised when using it, do not touch high-temperature parts such as flash tubes and surrounding metal components to avoid burns.
  8. Do not point the flash directly at the eyes (especially baby's eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
  9. If the flash tube or LED Modeling Lamp is damaged or thermally deformed, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents.
  10. Do not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
  11. Disconnect power source or remove batteries (if it has one) before replacing flash tube, protective glass, or fuses. Allowing 10 minutes to cool before replacing flash tube, and wear insulated or heat resistant gloves when operating.
  12. Turn off power before connecting or disconnecting plugs from outlets. Ensure plugs are fully inserted when connecting.
  13. Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.
  14. If an extension cord is needed, use the original extension cord or choose one with a rated current equal to or greater than the device. Using an extension cord with a smaller rated current may overheat and catch fire.
  15. The products have long power cords, please place them properly to avoid contact with heat sources or tripping others. It is recommended to use the original power cord. Damage caused by non-original cords is not covered by the warranty.
  16. The power plug of the studio flash can serve as a power-off switch, it should always be easily operable. Please disconnect the power when not in use.
  17. Unplug the equipment power plug from the power socket before cleaning or maintenance. Do not pull the power cord forcibly, use both hands to hold the plug end and pull it out.
  18. This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. It should be installed in a ventilated and dry location and avoid using in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.
  19. Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.
  20. Before storing the device, ensure it has completely cooled down and the power cord is unplugged, then put it in the protective case or a ventilated dry location.
  21. Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
  22. Do not use or store this device in potentially explosive environments.
  23. Maintain at least 1 meter distance between the lamp head and the user, other people, and heat-sensitive or flammable items during and after use.
  24. Do not cover the heat dissipation port!
  25. Do not use accessories not been approved by our company, as this may cause fire, electric shock or personal injury.
  26. Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
  27. This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check official website for latest instruction manual and product updates.
  28. The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty.
  29. Unauthorized repairs will void the warranty and will incur charges.
  30. Failures from improper operation is not covered under warranty.

3. What's Inside

The package includes the following items:

  • Flash Body ×1
  • Protective Cover ×1
  • Power Cord ×1
  • Instruction Manual ×1
Contents of the Godox SK400II package including flash body, protective cover, power cord, and instruction manual.
Figure 3.1: What's in the Box

Separately Sold Accessories:

  • Power Supply: Power inverter.
  • Trigger: 2.4GHz Trigger (X1, X2, X3, X3Pro, XT16), 433MHz Trigger (FT-16).
  • Optical Accessories: Softbox, photographic umbrella, beauty dish, snoot, honeycomb, light stand etc.
Various Bowens Mount accessories like softbox, soft ball, snoot, honeycomb grid, beauty reflector, and standard reflector.
Figure 3.2: Compatible Bowens Mount Accessories (Sold Separately)

4. Names of Parts

Flash Body Overview:

Diagram of the Godox SK400II Flash Body with dimensions: 203*118*200mm, weight 1.4kg.
Figure 4.1: Flash Body Dimensions

Control Panel and Rear View:

Detailed view of the Godox SK400II control panel showing 2.4G Wireless, Godox USB Port, and 3.5 Sync Cord Jack connections.
Figure 4.2: Control Panel and Ports
No.Part Name
1Photocell Sensor
2LCD Display
3BUZZ Button (Beep)
4S1/S2 Button (Photocell)
5GR / CH Button (Channel/Group)
6External Wireless Control Socket
7Sync Cord Jack
8Select Dial + SET Button
9MOD / OFF Button (Modeling Lamp)
10TEST Button
11Fuse Holder
12Power Switch Button
13Power Outlet
14Flash Tube
15LED Modeling Lamp
16Accessory Mount
17Accessory Detaching Rod
18Bracket Locking Knob
19Direction Adjusting Handle

5. Setup

5.1 Flash Tube Installation/Replacement

Always disconnect the power and wear insulating gloves before operation to ensure safety.

  1. Loosen the wire securing the flash tube spring clip.
    Step 1: Loosening the wire securing the flash tube.
    Figure 5.1: Loosen Wire
  2. Grip between the two pins of the flash tube, and pull out the old flash tube vertically.
    Step 2: Pulling out the old flash tube.
    Figure 5.2: Remove Old Flash Tube
  3. Remove the sleeve from the pins of the old flash tube and install it onto the pins of the new flash tube.
    Step 3: Transferring the sleeve to the new flash tube.
    Figure 5.3: Transfer Sleeve
  4. Grip between the two pins of the new flash tube, align with the two copper posts on the flash head, and insert vertically.
    Step 4: Inserting the new flash tube into the flash head.
    Figure 5.4: Insert New Flash Tube
  5. Wrap the wire around the flash tube spring clip and tighten it to secure.
    Step 5: Securing the flash tube with the wire.
    Figure 5.5: Secure Flash Tube

5.2 Mounting and Angle Adjustment

  1. Mounting: Attach the flash unit onto an appropriate light stand. Adjust the mounting bracket for a good angle and make sure it is tightened and fixed.
  2. Angle Adjustment: Turn the adjustment handle counter-clockwise to loosen. Adjust to the desired angle. Turn the handle clockwise to tighten.
    Diagram showing vertical and horizontal rotation angle adjustment of the flash unit.
    Figure 5.6: Angle Adjustment

6. Operating Instructions

6.1 Power Switch

Connect the power supply using the included power cord. Turn on the Power Switch. Power off and disconnect the power source when not in use.

Note: Press and hold the SET button and turn on the flash to view its version.

6.2 Power Output Adjustment

Turn the Select Dial to adjust the flash output.

  • Range: 1/32 - 1/1 (or 5.0 - 10.0)
  • Step: 0.1

Notes:

  1. When adjusting from high to low power, press the TEST Button to discharge excess energy for accurate output.
  2. Press the TEST Button to fire a test flash and adjust the lighting effect.
  3. "--" indicates that the flash function is turned off.
Image showing a hand adjusting the Select Dial and pressing the SET button on the flash unit's control panel to change power output.
Figure 6.1: Adjusting Power Output
Video 6.1: Demonstration of flash operation and settings adjustment, including power and mode changes.

6.3 2.4G Wireless Settings

To perform 2.4G wireless flash shooting, a flash trigger (sold separately) is required. Ensure the Group and Channel of the trigger and flash are set to the same values.

  • Wireless ON/OFF: Synchronously press and hold the GR / CH button and S1 / S2 button to turn on/off the wireless function. The ((())) icon displayed on the panel indicates that the wireless is on. The channel and group can be adjusted when the wireless is on.
  • Channel (CH) Settings: Set the Channel to prevent signal interference.
    1. Press and hold the GR / CH Button until the Channel icon blinks.
    2. Turn the Select Dial to switch channels.
    3. Press the SET Button to confirm.
  • Group (GR) Settings:
    1. Press the GR / CH Button. The Group icon blinks.
    2. Press the GR / CH Button or turn the Select Dial to switch groups.
    3. Press the SET Button to confirm.
Diagram showing the Godox SK400II flash unit with built-in 2.4G wireless transmission, compatible with X1 and XT16 flash triggers.
Figure 6.2: Wireless Control Function with X1 and XT16 Triggers
Features section highlighting the wireless control function of the Godox SK400II flash unit, showing compatibility with X1 and XT16 triggers.
Figure 6.3: Wireless Control Function Overview

6.4 Wireless Control Port

Take the FT-16 flash trigger (sold separately) as an example:

  • Triggering via Flash Trigger: Insert the FT-16 receiver into the Wireless Control Port on the flash. You can adjust the power output and trigger the flash using the FT-16 transmitter.
  • Triggering via Camera Shutter: Insert the FT-16 transmitter into the camera hot shoe. The flash can be triggered by pressing the camera shutter.

6.5 Photocell Triggering

Press the S1/S2 button to switch among modes.

  • OFF: Photocell function is turned off.
  • S1 Photocell: With this function, the flash will fire synchronously when the main flash fires.
  • S2 Photocell (pre-flash): This is useful when cameras have pre-flash function. With this function, the flash will ignore a single "pre-flash" from the main flash and will only fire in response to the second, actual flash from the main unit.
Image showing S1/S2 Slave Trigger Mode and BUZZ Recycling Prompt buttons on the flash unit.
Figure 6.4: S1/S2 Slave Trigger Mode

6.6 Modeling Lamp

Press the MOD / OFF Button to cycle through OFF, Percentage, and PROP.

  • OFF: Modeling lamp is turned off.
  • Percentage: Adjust the brightness manually. Press the SET Button and turn the Select Dial to adjust.
  • PROP: Brightness follows flash power.

Modeling Lamp Auto Off: The modeling lamp turns off automatically when the flash fires. When the modeling lamp is on, press and hold the MOD / OFF Button to enable or disable this function. The 💡 appears on the screen when the function is enabled.

Protection Function: Modeling lamp will be off automatically after lighting for 4 hours, avoiding overheat due to long-time lighting when the user is not nearby.

Image demonstrating how to adjust the modeling lamp's light brightness manually from 5% to 100%.
Figure 6.5: Modeling Lamp Adjustment

6.7 Beep

Press the BUZZ button to turn on/off the beep. The ◄))) icon will be displayed on the display. Turn on the beep function, a “BI” sound will be heard at each setting operation and when it's fully charged.

6.8 Memory Function

The device is equipped with memory function for the panel setting. It will help remember the panel setting 3 seconds after you set it. When starting up the flash next time, the panel setting will be the same as that before powering it off.

6.9 Sync Triggering

The Sync Cord Jack is a Φ3.5 mm plug. Insert a sync cord or trigger plug here and the flash will be fired synchronously with the camera shutter.

7. Troubleshooting: Alarm Display

To ensure safe operation, the system continuously performs preventive protection. If an issue occurs, an alarm will be displayed:

DisplayWarning
E0The temperature sensor is not connected.
E1When charging, the capacitance and voltage are not rising within 1 second.
E2The fastest heating-up component is over the extra temperature.
E3Discharged capacitance and voltage > rating +10%

Alarm sounds, BIBI, ringing per 0.5 second. Press SET button to stop alarming.

8. Specifications

The technical specifications for the Godox SK400II (and SK300IIIV for comparison) are as follows:

Product Information table detailing Model, Max Power, Guide Number, Color Temperature, Operating Voltage, Power Output Control, Modeling Lamp, Recycle Time, Triggering Method, Flash Duration, Fuse, Dimension, and Weight.
Figure 8.1: Product Information Table
ModelSK300IIIVSK400IIIV
Flash Power300 Ws400 Ws
Guide Number (m ISO 100)5865
Output Power ControlOFF, 1/32 ~ 1/1 (or 5.0 ~ 10.0)
Recycle Time0.1 - 1.5s
Flash Duration (t0.1)1/200s ~ 1/380s1/260s ~ 1/170s
Triggering MethodsSync cord, photocell triggering, test button, wireless control port, 2.4G wireless
CCT5700 ± 200K
Modeling Lamp Power10W
Modeling Lamp Level5% - 100%
Power Source VoltageAC 100V-120V ~ 50/60Hz or AC 200V-240V ~ 50/60Hz
Parameters output from the sync cord jack5V
Parameters output from the USB port5V/200mA (only for Godox receiver)
FuseAC 200V-240V~50Hz: 5A
AC 100V-120V~60Hz: 8A
DimensionFlash diameter: Φ12.8 cm
Height with handle: 23.5 cm
Length with protective cover: 31.8 cm (SK300IIIV)/34.5cm (SK400IIIV)
Net WeightApprox. 2.1 kgApprox. 2.3 kg

Specifications and data may subject to changes without notice.

9. Maintenance

  • Impact Protection: The device may malfunction if subjected to strong shocks or vibration.
  • Keep Dry: This product is not waterproof. Do not operate with wet hands or use in the rain, bathrooms, or other humid environments.
  • Temperature Precautions: Avoid sudden temperature changes, such as moving from a cold environment to a warm one, which may cause internal condensation. To prevent this, place the device in a protective bag beforehand to allow it to adjust to the temperature change.
  • Magnetic Interference: Keep away from strong electromagnetic field sources, such as radio transmitters, to prevent electromagnetic interference from affecting device performance.
Diagram showing the built-in fan outlet for overheating protection and extending flash life.
Figure 9.1: Fan Outlet for Heat Dissipation

10. User Tips

While no specific user tips were provided in the reviews or Q&A, here are some general recommendations for optimal use:

  • Always ensure the flash is securely mounted on a light stand to prevent accidental falls.
  • When using the modeling lamp for extended periods, monitor its temperature and allow for cooling breaks to prevent overheating.
  • Familiarize yourself with the wireless triggering system (X1/XT16) for seamless remote control and creative lighting setups.
  • Regularly check the flash tube for any signs of damage or wear, and replace it as needed to maintain optimal performance.

11. Warranty and Support

Dear customers, this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Applicable Products:

The document applies to the products listed on the Product Maintenance Information. Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period:

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day (purchase date) when the product is bought for the first time. And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service:

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases:

The guarantee and service offered by this document are not applicable in the following cases:

  1. The product or accessory has expired its warranty period;
  2. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;
  3. Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;
  4. The original identifying information of product or accessory is modified, alternated, or removed;
  5. No valid warranty card;
  6. Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
  7. Breakage or damage caused by force majeure or accident;
  8. Breakage or damage that could not be attributed to the product itself.

Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information:

PartsMaintenance Period (month)Warranty Service Type
Internal circuit board12Customer sends the product to designated site
Others (flash tube, optical accessories, cables, packages, etc.)NoWithout warranty

Godox After-sale Service Call: +86-755-29609320-8062

For more information, you can also visit the official Godox website: www.godox.com

12. Regulatory Information

Declaration of Conformity

GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states. For more information of DoC, Please click this web link: https://www.godox.com/eu-declaration-of-conformity/. The device complies with RF specifications when the device used at 0 mm from your body.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

IC Warning

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.