Godox SK400II

Contents

Godox SK400II Professional Studio Flash Strobe

Model: SK400II

400Ws GN65 Studio Flash Light for Sony, Nikon, Canon

1. Introduction

Thank you for purchasing the Godox SK400II Professional Studio Flash Strobe. This compact and powerful studio flash is designed for professional photographers, offering stable output, fast recycling, and a built-in Godox 2.4G Wireless X System for versatile control. It is compatible with various camera systems including Sony, Nikon, and Canon when used with appropriate triggers.

The SK400II features a large capacitance for speedier recycle times, reducing the time to 0.1-1s, significantly faster than its predecessor, the SK400 (0.4-3s).

Godox SK400II Compact Studio Flash with Wireless X System
Figure 1.1: Godox SK400II Compact Studio Flash with Wireless X System.

2. Safety Warnings and Precautions

Please read and understand all safety instructions before using this product.

  • Do not disassemble the product. Should repairs become necessary, this product must be sent to an authorized maintenance center.
  • Always keep this product dry. Do not use in rain or in damp conditions.
  • Keep out of reach of children.
  • Do not use the flash unit in the presence of flammable gas. In certain circumstances, please pay attention to the relevant warnings.
  • Do not leave or store the product if the ambient temperature reads over 50°C.
  • Turn off the flash trigger immediately in the event of malfunction.
  • Observe precautions when handling batteries (if applicable for external triggers):
    • Use only batteries listed in the manual. Do not use old and new batteries or batteries of different types at the same time.
    • Read and follow all warnings and instructions provided by the manufacturer.
    • Batteries cannot be short-circuited or disassembled.
    • Do not put batteries into a fire or apply direct heat to them.
    • Do not attempt to insert batteries upside down or backwards.
    • Batteries are prone to leakage when fully discharged. To avoid damage to the product, be sure to remove batteries when the product is not used for a long time or when batteries run out of charge.
    • Should liquid from the batteries come into contact with skin or clothing, rinse immediately with fresh water.

Note: These warnings are adapted from the Godox XProS TTL Wireless Flash Trigger manual and are provided for general safety guidance.

3. Product Overview

3.1 Physical Features

Godox SK400II studio flash unit
Figure 3.1: Front view of the Godox SK400II studio flash unit.
Dimensions of the Godox SK400II flash unit
Figure 3.2: Dimensions of the Godox SK400II flash unit (approx. 203*118*200mm, Weight: 1.4kg).

3.2 Control Panel

The rear panel of the SK400II features an LCD display and various buttons and dials for controlling the flash functions.

Detailed view of the SK400II control panel and ports
Figure 3.3: Detailed view of the SK400II control panel, showing the LCD display, function buttons, select dial, power switch, USB control port, and 3.5mm sync cord jack.
  • LCD Display: Shows current settings for power output, channel, group, and other modes.
  • Select Dial + SET Button: Used to adjust power output, modeling lamp brightness, and navigate menu options.
  • GR/CH Button: Group/Channel selection.
  • S1/S2 Button: Slave trigger mode selection.
  • BUZZ Button: Recycling prompt on/off.
  • MOD/OFF Button: Modeling lamp on/off.
  • TEST Button: Manual test flash.
  • Power Switch: Turns the unit on/off.
  • USB Control Port: For connecting a Godox USB wireless receiver (e.g., XTR16) or for firmware updates.
  • 3.5 Sync Cord Jack: For wired synchronization with cameras or other triggers.
Select Dial + SET Button for power output adjustment on SK400II
Figure 3.4: Adjusting power output using the Select Dial and SET Button. Power is adjustable from 1/16 to 1/1.

4. Installation and Initial Setup

4.1 Mounting the Flash Unit

The SK400II comes with a mounting bracket that allows for vertical and horizontal rotation. Attach the flash unit to a light stand using the provided bracket.

Angle adjustment for vertical and horizontal rotation of the SK400II
Figure 4.1: Vertical and Horizontal Rotation Angle Adjustment.

4.2 Power Connection

Connect the power cable to the AC input on the rear of the flash unit and then to a suitable power outlet. Ensure the voltage matches the unit's requirements (AC200-240V/50Hz or AC100-120V/60Hz).

4.3 Initial Power On

Flip the power switch to the 'ON' position. The LCD display will light up, indicating the unit is ready for operation.

Video 4.1: Demonstration of powering on the Godox SK400II, adjusting power settings, and performing a test flash.

5. Basic Operation

5.1 Adjusting Flash Power Output

Use the Select Dial and SET button on the control panel to adjust the flash power output. The power is freely adjustable from 1/16 to 1/1, and the selected value will be shown on the LCD display.

5.2 Modeling Lamp Control

The modeling lamp's brightness can be adjusted manually from 5% to 100%. This helps in predicting the light effect before shooting.

Modeling lamp adjustment on SK400II from 5% to 100%
Figure 5.1: Adjusting the modeling lamp brightness from 5% to 100%.

5.3 Slave Trigger Modes (S1/S2)

  • S1 Mode: Synchronously triggers the flash when receiving one external flash.
  • S2 Mode: Anti-preflash function, triggers the flash after the camera's preflash.
SK400II S1/S2 Slave Trigger Mode and BUZZ Recycling Prompt
Figure 5.2: S1/S2 Slave Trigger Mode and BUZZ Recycling Prompt button.

5.4 Recycling Prompt (BUZZ)

Press the BUZZ button to enable or disable the audible recycling prompt, which indicates when the flash is ready for the next shot.

5.5 Umbrella Input

The SK400II features an umbrella input for attaching soft umbrellas, reflector umbrellas, or softboxes, expanding your lighting possibilities.

Umbrella input on SK400II for soft umbrella/reflector
Figure 5.3: Umbrella input for various light modifiers.

6. Wireless Control with Godox XProS Trigger

The Godox SK400II is equipped with a built-in 2.4G wireless transmission system, allowing it to be controlled remotely by compatible Godox X System triggers like the XProS, X1, and XT16. The following instructions are adapted from the XProS trigger manual to explain how to control the SK400II.

Wireless control function of SK400II with X1 and XT16 triggers
Figure 6.1: Wireless control function of SK400II with X1 and XT16 triggers.
Exhibition of compatible triggers for SK400II (2.4G Wireless, Godox USB Port, 3.5 Sync Cord Jack)
Figure 6.2: Compatible trigger connection options: 2.4G Wireless, Godox USB Port, and 3.5 Sync Cord Jack.

6.1 Setting Up the XProS Trigger to Control SK400II

  1. Mounting and Power: Turn off your camera and mount the XProS transmitter onto the camera hotshoe. Power on both the XProS and your camera.
  2. Channel Setting: On the XProS, long press the <Zm/CH> button to select the channel value. Use the select dial to choose the appropriate channel (1-32). Press <SET> to confirm. Ensure the SK400II is set to the same channel.
  3. Group Setting: On the XProS, select the desired group (A-E or 0-F for 16 groups). Ensure the SK400II is assigned to the same group.
  4. Mode Setting: The SK400II primarily operates in Manual (M) mode for wireless control. Set the XProS trigger to M mode for the corresponding group.
  5. Power Output Adjustment: Use the XProS's select dial to adjust the power output for the SK400II. The value will be displayed on the XProS LCD and the SK400II will respond accordingly.
  6. Test Flash: Press the TEST button on the XProS to fire a test flash from the SK400II.

6.2 Wireless ID Settings (XProS)

To avoid interference, you can set a Wireless ID on the XProS trigger. Press the <MENU> button to enter C.Fn ID, then select an ID from 01 to 99. Ensure any receiving units (like a Godox X1R-S receiver connected to another flash) also have the same ID.

6.3 Multi Flash Settings (XProS)

The XProS trigger allows for multi-flash (stroboscopic) settings. In this mode, you can set the output value, number of flashes (Times), and frequency (Hz). Note that the SK400II's capabilities will determine the actual performance.

6.4 Modeling Lamp Control (XProS)

The XProS trigger can control the modeling lamp of the SK400II. When displaying multiple groups, press the <MOD> button on the XProS to turn the modeling lamp ON/OFF for the selected group.

7. Technical Specifications

Product Information table for SK400II
Figure 7.1: Detailed Product Information Table for Godox SK400II.
Godox SK400II Studio Flash Specifications
FeatureSpecification
ModelSK400II
Max Power (Ws)400Ws
Guide Number (m ISO 100)65
Color Temperature5600K ± 200K
Operating VoltageAC200-240V/50Hz or AC100-120V/60Hz
Power Output Control6.0-10.0 (1/16-1/1)
Modeling Lamp (W)150W
Modeling Lamp Level5%~100%
Recycle Time0.1-1.0s
Triggering MethodSync cord, Test button, Slave triggering, Wireless control port
Flash Duration1/2000 to 1/800s
Fuse5A
DimensionFlash diameter Φ12.7cm, height of flash with handle 23.2cm, length of flash with lamp lamp 38cm
WeightApprox. 2.1kg

8. Troubleshooting

If you encounter issues with your Godox SK400II, please refer to the following common troubleshooting steps:

  • Flash not triggering:
    • Ensure the power cable is securely connected and the unit is powered on.
    • Check if the flash is fully recycled (ready indicator light is on).
    • If using a wireless trigger, ensure the trigger and flash are on the same channel and group.
    • Verify that the trigger is compatible and properly connected (hotshoe or sync cord).
  • Overheating Protection: The SK400II has a built-in fan and overheating protection device to protect the flash safely and extend its life. If the unit overheats, it may temporarily stop firing. Allow it to cool down.
  • Fan outlet for overheating protection on SK400II
    Figure 8.1: Fan outlet for overheating protection.
  • Wireless Interference: If you experience inconsistent triggering or interference, try changing the wireless channel on both the flash and your trigger. Avoid environments with strong 2.4G signals (e.g., Wi-Fi routers, Bluetooth devices).
  • Recycle Time Issues: If the recycle time is slower than expected, ensure the power output is not set too high. Lowering the power output will result in faster recycle times.

9. Care and Maintenance

  • Avoid Sudden Drops: If the product receives strong shocks, impacts, or excessive stress, it may malfunction.
  • Keep Dry: This product is not waterproof. Malfunction, rust, and corrosion may occur if soaked in water or exposed to high humidity.
  • Avoid Sudden Temperature Changes: Condensation can occur with sudden temperature changes. To prevent this, place the flash in a handbag or plastic bag before moving it between environments with significant temperature differences.
  • Keep Away from Strong Magnetic Fields: Strong static or magnetic fields produced by devices such as radio transmitters can interfere with the product's normal operation.
  • Cleaning: Use a soft, dry cloth to clean the unit. Do not use harsh chemicals or abrasive cleaners.

10. What's in the Box

What's in the Box product list for SK400II
Figure 10.1: Contents of the SK400II package.

The standard package for the Godox SK400II typically includes:

  1. Modeling Lamp * 1
  2. Standard Reflector * 1
  3. Power Cable (US/UK/EU/AU) * 1
  4. Lamp Cover * 1
  5. SK400II Flash Unit * 1

11. Declaration of Conformity

GODOX Photo Equipment Co., Ltd. hereby declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states. For more information of DoC, please click this web link: https://manuals.plus/m/1c89f243bd223caca5c269cee3f8917f5e9d5162491b3148b033f5a662b2c9cd

The device complies with RF specifications when the device is used at 0mm from your body.

Note: This declaration is adapted from the Godox XProS TTL Wireless Flash Trigger manual and is provided as general regulatory information for Godox products.

12. Manufacturer Information

GODOX Photo Equipment Co., Ltd.

Address: Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China

Tel: +86-755-29609320(8062)

Fax: +86-755-25723423

E-mail: godox@godox.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.