1. Safety Information
Important Safety Instructions
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Remove hazards such as power cords, small items, or loose objects from the floor before cleaning.
- Fold carpet tassels under the rug and lift hanging curtains or tablecloths off the floor.
- For staircases or elevated areas, test whether the robot detects edges. Use barriers if necessary.
- Use only manufacturer-recommended accessories and original rechargeable battery and charging dock.
- Ensure the voltage matches the specifications on the charging dock.
- This device is for indoor home use only. Do not use outdoors or in commercial environments.
- Do not use water to rinse the device or wipe it with a wet cloth.
- Do not operate the robot on wet or flooded surfaces.
- Do not use near open flames or fragile items.
- Keep hair, fingers, and loose clothing away from moving parts and openings.
- Do not vacuum hard, sharp, flammable, or burning objects.
- Do not use a damaged charging dock or power cord.
- Keep the power cord away from heat sources and do not allow the robot to run over it.
- Ensure the dustbin and filter are installed correctly before use.
- Do not operate in a room where an infant is sleeping.
- Stop using the device if it has been dropped, damaged, exposed to water, or used outdoors. Contact customer service.
- Not suitable for high-pile carpets or certain dark-colored carpets.
Danger – Critical Safety Warnings
- Disconnect the product from power if not used for a long period. Always unplug the charging adapter before maintenance.
- WARNING: Non-rechargeable batteries must not be recharged.
- WARNING: For the purposes of recharging the battery, only use the detachable supply unit (model: K12V190060G) provided with this appliance.
- This product is equipped with a rechargeable battery with a capacity of 2900mAh.
- This appliance contains batteries that are only replaceable by skilled persons.
- If any battery leakage is found, stop using the product immediately and contact the after-sales service center for assistance.
- Do not power the device via external switches or circuits controlled by utility services.
- If the power cord is damaged, it must be replaced by the manufacturer or authorized agent.
- Maintain at least 20 cm distance between the antenna and your body during operation.
- Frequency bands: Bluetooth 2402–2480 MHz; Wi-Fi 2412–2472 MHz.
- Maximum RF transmission power: Bluetooth <10 dBm (EIRP), Wi-Fi <20 dBm (EIRP).
- Before discarding the product, power it off and remove the battery. Dispose of batteries according to local regulations.
- Do not incinerate the product or battery even if damaged.
- Use the product only as described in this manual. ILIFE is not responsible for loss or injury from misuse.
CLASS 1 CONSUMER LASER PRODUCT
The ILIFE V30 Robotic Vacuum Cleaner contains Class 1 laser products. Ensure proper handling and operation as per safety guidelines.
Laser Model: VP100L
- Invisible laser radiation
- Exposure near aperture may cause burns
- Wavelength: 905nm
- Output power: 1.5w
- Frequency: 1MHz
- Pulse duration: 1.5ns
- Complies with EN 50689:2021 & EN 60825-1:2014+A11:2021
Laser Model: D3A3
- Invisible laser radiation
- Exposure near aperture may cause burns
- Wavelength: 940nm
- Output power: 6mW
- Frequency: Steady on
- Complies with EN 50689:2021 & EN 60825-1:2014+A11:2021
Network Interface
- Bluetooth (Bluetooth LE) Interface: Used for near-field device discovery and initial connection, allowing your mobile phone and other smart devices to quickly find and establish communication.
- Wi-Fi Interface: Operates in an unconnected, configurable listening mode, continuously listening for Wi-Fi signals. Supports 2.4GHz Wi-Fi band for stable connections.
- P2P Interface: When powered on, the robot broadcasts its location to the local network, enabling direct communication with the mobile app for real-time control and data transmission.
Service
- Device Broadcast Service: The device continuously broadcasts its own information via Bluetooth, including device name, type, and unique identifier, allowing nearby smart devices to identify and connect.
- Network Service: Facilitates initial connection and subsequent Wi-Fi configuration. Transfers router's Wi-Fi network name and password from the app to the device.
- P2P Service: Enables automatic network configuration and remote control, allowing real-time commands and data synchronization (e.g., cleaning maps and progress).
2. About Your V30
2.1 What's in the Box
The ILIFE V30 Robot Vacuum Cleaner comes with the following components:
Video: Unboxing and overview of included accessories for the ILIFE V30.
- Robot Vacuum
- Charging Dock
- Power Adapter
- Mop Bracket
- Mop Cloth (×2)
- Remote Control
- Cleaning Brush
- High Performance Filter
- User Manual (PDF available separately)
- Side Brush
- 2-in-1 Roller Brush
- AAA Battery (×2)
2.2 Technical Specifications
| Specification | Details |
|---|---|
| Model | V30 |
| Dimensions | 330x330x95 mm |
| Battery Type | Li-ion |
| Charging Type | Auto Charging / Manual Charging |
| Charging Time | < 360 minutes |
| Dustbin Capacity | 0.2 L |
| Water Tank Capacity | 200 ml |
| Net Weight | 2.7 kg |
| Cleaning Modes | Auto, Spot, Edge, Daily Schedule |
| Main Body Button Type | Mechanical Button |
| Weight | 3 - 6 KG |
| Number of operating modes | 3-4 |
| Filter Type | HEPA |
| LCD | No |
| Cleaning Route | Planned Type |
| Bag Or Bagless | Bagless |
| Cord Length (m) | WireLess |
| Handle Material | Others |
| Timing Reservation | Yes |
| Dust Storage Type | Dust Box |
| Installation | Robot |
| Certification | ce |
| Power (W) | 40w |
| Function | Sweep Suction |
| Voltage | 100-240V |
| Remote Control | Yes |
| Origin | Mainland China |
| Warranty | 2 years |
2.3 Product Overview
Robot Components
The ILIFE V30 features a sleek design with intuitive controls and advanced sensors for efficient cleaning.

Image: Top view of the ILIFE V30 Robot Vacuum Cleaner, showing the Obstacle Sensor, Start/Pause Button, and LiDAR Sensor.

Image: Bottom view of the ILIFE V30 Robot Vacuum Cleaner, showing Cliff Sensors, Charging Pins, Side Brush, Side Wheels, Nose Wheel, Battery Compartment, Roller Brush, 2-in-1 Dustbin & Water Tank, and Water Tank Release Button.
Water Tank Assembly

Image: Exploded view of the Water Tank Assembly, including Primary Filter, Sponge Filter, High Performance Filter, Water Inlet Plug, Dust Outlet, Mop Bracket, and Mop Cloth.
Charging Dock
The charging dock features a Power Supply Socket, Signal Light, Power Adapter connection, and Charging Pins.
2.4 Buttons and Indicator Lights Instruction
Robot Button Instruction
| Button | Operation | Function |
|---|---|---|
| Power (Main Button) | Press and hold 2 seconds | Power on |
| Power (Main Button) | Short press | Start/Pause cleaning |
| Power (Main Button) | Press and hold 3 seconds | Power off |
| Power (Main Button) | Quick double presses | Return to charging dock |
| Power (Main Button) | Press and hold 25 seconds | System reset |
Robot Indicator Lights Instruction
| Light Color | Status | Description |
|---|---|---|
| Green | Solid | Sufficient battery |
| Green | Blinking | Standby mode |
| Orange | Blinking | Low battery |
| Orange | Blinking slowly | Charging |
| Red | Flashing | Error |
2.5 Remote Control Guide
Before using the remote, insert two AAA/R03 batteries. Remove the batteries if not used for a long time.
| Button | Function |
|---|---|
| Power | Wake the robot from sleep / Start or pause cleaning |
| Direction Arrows | In standby mode: Forward, Left, Right (Not functional during running) |
| Suction | Switch Suction Level by Each Press: Standard → Strong → Max → Silent → Standard |
| Path Mode | Starts standard zigzag cleaning across the entire area |
| Edge Mode | Cleans along walls and furniture edges |
| Spot Mode | Deeply cleans a 1.5m × 1.5m area in a spiral pattern |
| Home | Send the robot back to the charging dock manually |
3. Getting Started
3.1 Important Pre-Cleaning Notes
Daily Use Encouraged: Frequent use helps the robot learn your home layout for more efficient path planning and reduced missed spots.
- A. Remove loose items from the floor: Clear cables, clothing, or small objects that could get tangled in the wheels or brushes.
- B. Fold the rug's tassel trim underneath: Prevent tangling during cleaning. Avoid using on high-pile or thick rugs (>18mm or 0.71").
- C. Block off dangerous zones: For areas like fireplaces, vents, or staircases, place physical barriers or set "No-Go Zones" in the app.
- D. Avoid use on floor with excessive water: Avoid vacuuming large amounts of water as it will potentially damage the robot.
- E. Obstacle height limit: The robot can climb over thresholds up to 20mm (0.79").
- F. Cliff sensor limitations: Although the robot includes anti-drop sensors, performance may decrease on dark carpets or reflective surfaces, or in situations where the floor is stained. Use physical barriers as needed.
3.2 Installing and Using the Charging Dock
Placement Guidelines
- Place the charging dock on a hard, flat surface against a wall.
- Ensure there are no obstacles within 2 meters in front and 1 meter on both sides.
- Avoid placing it in areas with strong sunlight or reflective surfaces.
- Keep it away from places where pets sleep to avoid noise disturbance.
Power Connection
Connect the adapter with the charging dock. Plug in the power cable. Once powered, the signal light of the dock will light up.
Turn on the robot
Press and hold the AUTO button for 2 seconds to turn on, and press and hold it for 3 seconds to turn off.
Note:
- After the robot finishes its work, please do not turn it off, and fully recharge it for the next run.
- If the robot pauses working for more than ten minutes, it will enter sleeping mode. If you need to wake up the robot again, you need to press the AUTO button once.
3.3 Charging the Robot
Charging Steps
- Proper Placement: Align the robot with the charging pins on the charging dock. When connected properly, the robot's orange charging light will blink slowly, indicating it is charging.
- Charging Completes: When all indicator lights turn off, the battery is fully charged.
Tip:
- Recharge the robot after each use to extend battery life.
Important Notes
- In Daily Use:
- Make sure the charging pins on the robot and charging dock remain clean to avoid poor contact.
- Store the robot on the charging dock with the charging dock powered on.
- Charge for 6 hours for the first time.
- When Not in Use: For long-term storage, fully charge the robot, turn it off (press and hold power for 3 seconds), and store it in a dry, ventilated place.
3.4 Installing and Using the Water Tank & Mop
Installation Steps
- Remove the Water Tank: Press the water tank's release button and pull the tank backward to remove it.
- Fill the Water Tank: Open the rubber plug on the tank and fill with clean water. Tip: Use purified water to reduce limescale buildup. Reseal the plug tightly to prevent leakage.
- Attach the Mop Cloth: Smooth the mop cloth onto the bracket and use velcro to secure it. Align the bracket with the bottom of the tank and slide it in until it clicks into place.
- Start Mopping: Reinstall the tank into the robot. The robot will automatically detect the mop and switch to mop mode.
Important Notes
- Where Not to Use Mopping Mode:
- Do not use the mop on carpets. For best practice, zone out the carpet on app while mopping.
- Do not use hot water or cleaning agents (it may damage or clog the tank).
- Maintenance Tips: Monitor water levels during mopping; refill when low. After mopping, remove the mop and wash/dry it to avoid mildew or odors.
4. Using the ILIFE Clean App
4.1 Download the App
To access all features, it's recommended to control the robot through the ILIFE Clean App.
Network Compatibility
Supports 2.4GHz or dual-band 2.4GHz/5GHz networks. Does not support 5GHz-only networks.
Step-by-Step Setup
- Download the App: Scan the QR code (refer to user manual PDF page 19) or search for “ILIFE Clean” in your app store.
- Register/Login: Open the app and sign up or log in with your credentials.
- Enable Pairing Mode: Press and hold the AUTO button on the robot for 5 seconds. You'll hear "WiFi pairing started" and the WiFi light will start blinking slowly.
- Add Device: Tap "Add Device” or the “+” icon in the top right corner to begin connecting.
4.2 Wi-Fi Pairing Modes
Bluetooth Pairing Mode
Enable Bluetooth on Your Phone.
Pairing Steps
- Go to your phone's settings, turn on Bluetooth and enable Bluetooth permission for ILIFE Clean app.
- Return to the ILIFE Clean app — the device will appear automatically and tap "Add" to begin.
- Select your 2.4GHz Wi-Fi network and enter the password to go next.
- The device starts downloading.
- Device is added successfully and done.
4.3 Map Management
How to Access
Open the ILIFE Clean app → Tap “Settings" → Select "Manage Map"
Available Functions
- Create/Switch Maps: Perfect for multi-floor homes (up to 5 maps supported).
- Reset/Delete Maps: Delete or reset a saved map.
4.4 Setting No-Go & No-Mop Zones
It's recommended to complete a full-home mapping before setting restricted zones.
Zone Types
- No-Go Zone: Robot avoids both vacuuming and mopping in this area.
- No-Mop Zone: Robot vacuums but does not mop in this area.
- Virtual Wall: Acts as an invisible barrier the robot won't cross.
How to Set Zones
- Go to "forbidden edit" in the app.
- Tap Set Restricted Areas.
- Draw your desired zone and select the type.
- Save "Settings".
Note:
These features are for convenience and do not replace physical barriers in high-risk areas like staircases.
4.5 Scheduled Cleaning
Before You Start
Ensure the charging dock remains powered on. The robot should have sufficient battery charge.
How to Schedule
- Open the ILIFE Clean app.
- Go to Scheduled Cleaning.
- Set the desired time and recurrence (e.g., daily or weekly).
- Choose your preferred cleaning mode.
- Confirm your settings.
After Scheduling
- The robot will start cleaning automatically at the scheduled time.
- After cleaning, it will return to the charging dock.
4.6 Selecting Cleaning Modes
Start / Pause Cleaning
- In the App: Tap the “Start/Pause” button.
- On the Robot: Press the power button once to start or pause cleaning.
Tip:
It's recommended to create a full-house map before using room-by-room or zone cleaning.
Smart Cleaning Mode
- Tap “Start” in the app.
- The robot will leave the charging dock and automatically plan a cleaning route.
- It will return to the charging dock when cleaning is complete.
Room Cleaning Mode
Select specific room in the app for targeted cleaning.
Note:
Please refer to 4.7, you can customize suction power, water volume, and cleaning sequence per room.
Zone Cleaning Mode
- Draw a rectangular zone on the map in the app.
- Set the size and number of cleaning passes (e.g., clean 2x).
- The robot will clean that area and return to the charging dock.
Spot Cleaning Mode
- For localized messes like pet food or snack spills.
- Tap the target spot on the map.
- The robot will deep-clean a 1.5m × 1.5m area in a spiral pattern, then return to base.
Do Not Disturb Mode
- Ideal for nighttime or rest hours. In the app: Go to "Settings” → “Robot Settings" → Do Not Disturb.
- Once enabled, the robot will:
- Pause auto-charge and auto-resume cleaning.
- Shut down voice prompts.
4.7 Cleaning Plan Customization
Suction & Water Level Adjustment
In the app via: “Cleaning Plan” → Adjust suction power (Silent / Standard / Strong / Max) and water flow (Low / Medium / High)
Per-Room Customization
In the app via: “Cleaning Plan” → "Plan 1 / Plan 2” Set specific suction, water flow, number of passes, and cleaning sequence for each room.
5. Voice Assistant Setup (Alexa/Google Assistant)
Before setting up, please make sure:
- V30 is fully charged and connected to ILIFE Clean app.
- You own a supported voice assistant device (e.g., Amazon Echo, Google Nest). These devices are sold separately.
- Alexa or Google Home app is installed on your mobile device.
- You have an active account for your voice assistant.
Alexa Setup
- Connect your robot to the ILIFE Clean app.
- Open the Alexa app → Tap Skills & Games → Search SmartLife.
- Tap "Enable to Use”.
- Enter your ILIFE Clean account credentials and authorize access.
- Tap "Authorize".
- Alexa will search and link your robot automatically.
6. Cleaning & Maintenance
6.1 Recommended Maintenance Frequency
Always turn off the robot and unplug the power adapter before performing maintenance.
| Component | Clean Frequency | Replace Frequency |
|---|---|---|
| Mop Cloth | As needed | Every 3-6 months |
| Dustbin | Weekly | N/A |
| Filter | N/A | Every 1-1.5 months |
| Side Brush | Weekly | Every 3-6 months (or if damaged) |
| Roller Brush | Weekly | Every 6 months |
| Side Wheels | Monthly | N/A |
| Cliff Sensors | Monthly | N/A |
| Charging Contacts | Monthly | N/A |
6.2 Cleaning the Dustbin & Filter
- Press the release button to remove the 2-in-1 dustbin.
- Open the dustbin lid.
- Empty the dustbin.
- Remove the filters and rinse the dustbin with water.
- Dry thoroughly with a clean cloth.
- Replace the filter if necessary and reinsert the dustbin.
Note:
The filter is unwashable.
6.3 Cleaning the Water Tank and Mop Cloth
Mop Cloth
- Remove the mop bracket and peel off the cloth.
- Rinse with clean water and let it air-dry completely.
2-in-1 Water Tank
- Open the rubber plug and drain any leftover water.
- Wipe the tank clean and let it dry thoroughly.
6.4 Cleaning the Roller Brush
- Unlock and lift the brush cover.
- Remove the roller brush by pulling it upward.
- Use the provided tool to cut away tangled hair or debris.
- Rinse the roller brush and cover with water.
- Air-dry those components.
- Reinstall the roller brush and snap the cover back into place.
6.5 Cleaning the Side Brushes and Side Wheels
Side Brushes
Unscrew and remove the brushes. Clear hair or debris wrapped around them.
Side Wheels
Check and remove any obstructions caught in the wheels.
6.6 Cleaning the Sensors and Charging Pins
Cliff Sensors
Use a soft brush to gently clean the sensors on the underside of the robot.
Charging Pins
Wipe both the robot's and the charging dock's charging pins with a dry cloth to maintain charging efficiency.
6.7 Battery Care and Activation
For Long-Term Storage
- Charge the robot fully.
- Power it off (hold the power button for 3 seconds).
- Store in a dry, ventilated place. Recharge every 3 months to avoid battery degradation.
Battery Activation (After Deep Discharge or Long Inactivity)
- Align the robot on the charging dock.
- Charge it for 3 minutes and then remove it away. Repeat this process 3 times.
- Then charge continuously for 5-6 hours until it is fully charged when the indicator turns off.
7. Troubleshooting
7.1 Voice Alerts & Error Codes
When a malfunction occurs, the robot's indicator light will flash red and a voice alert will play. Use the table below to identify and resolve the issue.
| Voice Alert | Possible Cause | Solution |
|---|---|---|
| Side wheel/Side brush blocked | Hair or debris is caught | Check and clean side wheels/brushes |
| Please check the cliff sensor/Bumper is stuck | Bumper gets caught or stained/cliff sensors get stained | Clear and clean those components |
| Robot is stuck | Trapped by cords or obstacles | Remove the obstruction |
| Gyroscope initialization failed | Gyroscope failed to position due to robot skidding | Remove and relocate the robot |
7.2 Water Tank / Mopping Issues
| Issue | Possible Cause | Solution |
|---|---|---|
| Water tank leaking | Rubber plug not sealed | Reseal the plug |
| No water output while mopping | The water tank not installed properly or empty | Reinstall or refill the tank |
| Mop cloth falling off | Velcro not attached well or worn out | Secure the mop cloth or replace it |
7.3 App Issues
| Issue | Possible Cause | Solution |
|---|---|---|
| Can't connect to the app |
|
|
| Map not generated |
|
|
7.4 Robot Issues
| Issue | Possible Cause | Solution |
|---|---|---|
| Robot returns before finishing |
|
|
| Can't charge |
|
|
| Loud noise during operation |
|
|
| Frequently gets stuck |
|
|
| Skipped or repeated cleaning areas |
|
|
*If the issue persists:
- Press and hold the power button for 3 seconds to turn off, then press for 2 seconds to restart.
- If still unresolved, please contact customer support.
8. User Tips
- The anti-tangle roller is highly effective at preventing hair and pet fur from getting tangled.
- The mobile application and mapping features generally work well for efficient cleaning.
- Ensure the dustbin filter is not blocked for optimal dirt collection. High-efficiency filters have a service life of about six months.
- Regularly clean the wheels to prevent the robot from moving in circles or getting stuck.
- If the robot cleans in small areas or changes direction frequently, check and clean the nose wheel for obstructions.
- For loud noise during operation, check the main brush, side brush, and dust box filter for entangled foreign matter or blockages.
- Tidy up the environment by removing cables, slippers, and other objects to prevent the robot from getting stuck.
9. Warranty & Support
Warranty Information
The ILIFE V30 Robot Vacuum Cleaner comes with a 2-year warranty.
Customer Service
If you encounter any issues with your robot, feel free to contact our customer service or visit our website for further assistance.
- Customer Service Email (Europe): warranty_repair_EU@iliferobot.com
- Website: www.iliferobot.com
For more detailed information, please refer to the full user manual PDF available on the manufacturer's website.