Allsome BG-518801

Contents

ALLSOME BG-518801 Mini Bench Drill Press

Instruction Manual

Please read this instruction manual carefully before use.

1. Introduction

Dear Valued Customer,

Thank you for choosing the ALLSOME BG-518801 Mini Bench Drill Press. This high-precision micro drilling and milling tool is designed for use with various industrial and civilian materials, offering convenience and efficiency for your projects.

The BG-518801 series integrates intelligent CNC technologies, featuring an enlarged cast aluminum base, thickened column steel tube, a high-power motor, and a large working range. It utilizes a mechanical two-stage gear transmission for direct output with greater torque. Key features include speed regulation, speed display, depth display, laser focusing, and an integrated work light.

Its powerful numerical control functions make it an ideal choice for DIY enthusiasts and various workshops.

Before operating the machine, please read this manual thoroughly and adhere to all safety operating requirements.

2. Safety Warnings

  • Read Manual: Before operating, read the manual thoroughly and master basic operational skills.
  • Clean Workspace: Keep the floor around the machine clean, free of debris, oil, etc. Cluttered and dark areas can lead to accidents.
  • Appropriate Clothing: Wear appropriate clothing. Avoid loose clothing, jewelry, long hair, or gloves near moving parts.
  • Authorized Users: Do not allow unfamiliar or inexperienced individuals to operate the machine. Keep children away from the machine.
  • Maintain Distance: Keep bystanders and children at a safe distance when using the machine.
  • Power Supply: Ensure the power supply matches the machine's requirements (220V~50Hz) and is equipped with effective leakage protection and a circuit breaker.
  • Prevent Unintentional Start: Ensure the power switch is in the "OFF" position before connecting to the power supply.
  • Remove Tools: Before starting, ensure all keys, wrenches, and other tools have been removed from the machine.
  • Correct Use: Do not misuse the machine. Use appropriate speed and feed force for the intended purpose.
  • Environment: Do not use electrical equipment in damp environments. Protect against rain and water ingress.
  • Laser Safety: Strictly prohibit looking directly at the laser source with your eyes to avoid damage.

3. Product Components

Familiarize yourself with the main components of your drill press:

Labeled diagram of ALLSOME BG-518801 Drill Press components

Figure 1: Main Components of the Drill Press

  1. Depth Stop Rod
  2. Main Unit
  3. Power Switch (Safety Emergency Stop)
  4. Display Screen (LCD)
  5. Digital Control Button
  6. Speed Controller (Speed Control Knob)
  7. Chuck
  8. Base
  9. Operating Lever
  10. Fixed Clamp
  11. Adjustment Screw
  12. Rack
  13. Column
  14. Laser
  15. Lighting
  16. Shift Knob

4. Setup and Installation

Before installation, unpack the product and check if all items are present. Refer to the included items list below.

4.1 Included Items

Item Description Quantity
Main Unit with Column Assembly (incl. Chuck) 1 set
Base 1 pc
Operating Handles 3 pcs
Spare Carbon Brushes 1 pair
Hex Keys (4mm, 6mm) 1 each
Chuck Key (13mm) 1 pc
Open-End Wrench (16mm) 1 pc
Cone Point Set Screw (M8) 1 pc

4.2 Installing the Base

  1. Place the base (8) on a flat, stable workbench.
  2. Hold the main unit with both hands, align the steel tube (13) with the mounting hole on the base (8), and insert it. Visually ensure the drill chuck (7) is roughly aligned with the center hole of the base.
  3. Tighten the screw (part 94 in parts list, likely a set screw for the column) using the attached 4mm hex key.

4.3 Installing the Operating Handle

  1. Screw the bakelite ball (part 117 in parts list) onto the operating handle (9).
  2. Then screw the operating handle into the threaded hole on the aluminum head (part 119 in parts list) until tight. Note that the threaded hole has a certain tilt angle.

4.4 Installing or Removing the Drill Chuck

Ensure the chuck connecting parts are free of oil, dust, and other foreign matter. The three jaws must be retracted below the chuck nose line.

Installing the Chuck:
  1. The output shaft (part 87 in parts list) uses a thread to connect to the drill chuck (7).
  2. Use the open-end wrench (16mm) to hold the output shaft. Tighten the chuck onto the output shaft.
  3. Insert the bar of the chuck key (13mm) into the side hole of the chuck and tighten further.
Removing the Chuck:
  1. Use the open-end wrench (16mm) to hold the output shaft.
  2. Insert the bar of the chuck key (13mm) into the side hole of the chuck.
  3. Tap the key's bar with a wooden mallet to loosen the chuck.

4.5 Installing Drill Bits (or Milling Cutters)

  1. Insert the chuck key into the chuck adjustment hole and turn counterclockwise to loosen the chuck.
  2. Insert the drill bit (or milling cutter) into the chuck.
  3. Insert the key into the three keyholes of the chuck in sequence, turning clockwise to tighten the chuck.

Note: If only one keyhole is used for tightening, the chuck may loosen easily.

5. Operating Instructions

WARNING: Before making any adjustments or plugging in the machine, ensure the power switch is in the OFF "O" position and the plug is disconnected from the power outlet.

5.1 Using the Power Switch

  1. When the switch knob (3) is turned to position "0", the machine's power is off.
  2. When the switch knob is turned to position "I" (or similar power-on indicator), the display screen activates.
  3. When the switch knob is turned further to activate the motor, the display screen and motor are active. Turning back to the "I" position or "0" turns off the motor.
  4. Emergency Power-Off: During motor operation, if a dangerous situation occurs, press the switch knob directly to achieve emergency power-off and locking. Turn the knob to position "0" to release the power-off lock.

5.2 Using the Display Screen (LCD)

Close-up of the control panel with LCD display

Figure 2: Control Panel and LCD Display

  1. Use the left button (often labeled "rpm/mm") to select display mode: "Output Speed" (rpm) or "Head Height" (mm).
    • In speed display mode, "Speed" appears at the bottom left, and the output speed value is displayed in the center.
    • In head height display mode, "Depth" appears at the bottom left, and the screen center displays the height change value (positive or negative) relative to the "0" position.
  2. In "Head Height" mode, the middle "0" button performs a "Zero Reset" of the height value.
  3. The button labeled with a laser icon turns the laser on/off.
  4. The button labeled with a light bulb icon turns the work light on/off.

5.3 Using the Speed Control Knob

Rotating the "Speed Control Knob" (6) adjusts the machine's output speed. The specific speed value is displayed on the screen (ensure display is in speed mode). Clockwise rotation increases speed; counterclockwise rotation decreases speed.

5.4 Using the Gear Shift Knob

Rotating the "Gear Shift Knob" switches between "High Speed" and "Low Speed" gears:

  • Gear "1" (Low Speed): Speed range 200 - 850 rpm.
  • Gear "2" (High Speed): Speed range 600 - 2500 rpm.

Note: Reduce the machine speed to the minimum before shifting gears to reduce impact and extend service life.

5.5 Selecting Drill Bit Speed

A recommended speed table is affixed to the machine's housing for reference. Actual drilling conditions may vary.

Speed compatibility chart for Steel and Aluminium

Figure 3: Material-Work Compatibility Chart (RPM vs. Material)

  • Drill bits need to be sharpened regularly.
  • Apply cutting fluid if necessary to avoid drill bit burning or discoloration.
  • For harder steel (hardness exceeding 20HRC), consider reducing the speed further.

5.6 Using the Laser

Turning on the laser assists in aligning the drill bit with the intended drilling position on the workpiece. The intersection point of the laser indicates the vertical position of the drill bit.

Laser Adjustment:
  1. Peel off the label covering the laser adjustment screw.
  2. Loosen the hex set screw securing the laser through the round hole in the casing.
  3. Use a flathead screwdriver to turn the groove on the front of the laser head to adjust the cross beam to the center of the drill bit.
  4. Tighten the set screw.

5.7 Adjusting Spindle Travel (Depth Stop)

  1. Loosen the plastic screw (part 74 in parts list) on the depth stop rod.
  2. Press down the operating lever (9) to lower the drill bit to the required position.
  3. Let the depth stop rod (1) descend onto the fixed clamp (10).
  4. Tighten the plastic screw. This will stop the drilling at the set depth.

5.8 Adjusting the Head Height

  1. Hold the operating lever (9) by hand, then loosen the clamping handle (part 132 in parts list).
  2. Move the operating lever to raise or lower the main unit together with the fixed clamp (10) to the desired position.
  3. Re-tighten the clamping handle.

5.9 Adjusting the Clamp's Flexibility

Firmly hold the operating lever (9), then loosen the clamping handle (part 132 in parts list). Use the 4mm hex key to adjust the set screw (part 123 in parts list) so that the friction between the main unit and the steel tube is moderate.

  • If friction is too low when loosened, the main unit may fall easily.
  • If friction is too high, moving the operating lever and raising/lowering the main unit will be laborious.

5.10 Adjusting the Gap Between the Steel Tube and Main Unit

After long-term use or use as a milling machine, check the gap between the main unit and the steel tube (13). If the gap is too large or too small, adjust the set screw (part 78 in parts list).

  • Do not overtighten the adjustment screw; too small a gap makes it difficult to press down or return the main unit. Too loose a gap causes swaying and affects precision.
  • Regularly add lubricating grease to the steel tube.

5.11 Adjusting the Main Unit Return Force

After long-term use, check the force required to press down and return the main unit. It should allow the unit to reset easily with a slight upward push on the operating lever. If too tight, operation will be laborious. If too loose, the return force may damage precision. Use the 6mm hex key to adjust the set screw (part 106 in parts list).

5.12 Milling Machine Function

Adjust the head height to position the milling cutter correctly. Then tighten the hex screw (part 78 in parts list) and the set screw (part 106 in parts list) to restrict the up and down movement of the main unit. It can then be used as a milling machine.

Note: It can only be used as a milling machine after equipping with a work table (sold separately).

6. Maintenance

After each use, maintain and service the machine:

  • Remove dust and water stains from the machine.
  • Add lubricating grease to rotating parts as needed.
  • If not used for a long time, unplug the power cord and store the machine properly in a dry, safe place.
  • Regularly check and sharpen drill bits for optimal performance and to prevent damage.

7. Troubleshooting

This section provides solutions to common issues. For problems not listed, please contact customer support.

Problem Possible Cause Solution
Machine does not power on No power supply; Power switch off; Loose connection Check power outlet and cable; Turn power switch on; Secure all connections
Motor runs but drill bit does not rotate Chuck not tightened; Drill bit loose Tighten chuck with chuck key; Re-insert and tighten drill bit
Excessive vibration or noise Loose components; Unstable workpiece; Worn drill bit Check all screws and tighten; Secure workpiece firmly; Replace or sharpen drill bit
Inaccurate drilling Loose column/main unit; Unstable base; Worn drill bit Adjust gap between steel tube and main unit; Ensure base is stable; Replace or sharpen drill bit
Laser not visible or misaligned Laser off; Misaligned laser Turn laser on via control panel; Adjust laser alignment as per instructions

8. Specifications

Parameter Value
Model Number BG-518801
Rated Voltage / Frequency 220V~50Hz
Rated Input Power 800W
No-Load Speed 200-2500 r/min
Chuck Capacity 1.5-13mm
Max. Spindle Travel 90mm
Working Radius 147mm
Weight 11.82KG
Certification CE
Power Source AC
Motor Type Brushed

8.1 Dimensions

Technical drawing with overall dimensions of the drill press

Figure 4: Overall Dimensions (Height: 645mm, Max Chuck to Base: 205mm)

9. User Tips

  • Ensure Stability: Always place the drill press on a firm, level, and stable workbench to minimize vibration and improve drilling accuracy.
  • Secure Workpiece: Use clamps or a vise to firmly secure your workpiece to the base. This is crucial for safety and precision, especially when dealing with harder materials or larger drill bits.
  • Check Calibration: If experiencing accuracy issues, double-check the alignment of the column, main unit, and laser. Adjust as per the manual's instructions.
  • Proper Speed Selection: Refer to the material compatibility chart and adjust the speed (both gear and knob) according to the material and drill bit size to prevent overheating and ensure clean holes.
  • Regular Lubrication: Keep the column and moving parts lightly lubricated to ensure smooth operation and prevent wear.

10. Warranty and Support

For warranty information, please refer to the documentation provided at the time of purchase or contact your seller directly. This manual does not include specific warranty details.

For technical support or service inquiries, please contact the authorized dealer or manufacturer's customer service.

11. Product Demonstration Video

Watch this video for a visual guide on the drill press's features and operation:

Product demonstration showing drilling, chuck changes, speed adjustments, and use with accessories.

© 2023 Allsome. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.