BAOFENG MINI 5

Contents

Baofeng MINI 5 Walkie Talkie User Manual

Model: MINI 5

1. Introduction

Thank you for purchasing the Baofeng MINI 5 Walkie Talkie. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation of your device.

This manual covers essential information regarding the setup, operation, maintenance, and specifications of your MINI 5 Walkie Talkie.

Video 1.1: Overview of Baofeng MINI 5 Walkie Talkie features and design.

2. Safety Information and Regulations

2.1 General Warnings

WARNING!

European Users should note that operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU.

ATTENTION!

When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. You can use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.

ATTENTION!

Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio, which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.

PMR446, FRS, GMRS, MURS: You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.

2.2 FCC Part 15 / IC Compliance

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

For hand-held operation, the radio should be held 1 inch (2.54 cm) from the user's face to comply with FCC RF exposure requirements.

For body-worn operation, this device has been tested and meets the Industry Canada RF exposure guidelines when used with our company accessories supplied or designated for this product. Use of other accessories may not ensure compliance with Industry Canada RF exposure guidelines.

2.3 Precautions for Portable Terminals

Operating Prohibitions:

  • Do not operate the product in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not operate the product near or in any blasting area.
  • Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

Important Tips:

  • Do not use any unauthorized or damaged accessory.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Do not keep the product receiving at high volume for a long time.
  • For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
  • Keep the product and its accessories out of reach of children and pets.
  • Operate the product within the specified temperature range.
  • Continuous transmission for a long time may lead to heat accumulation. Allow for proper cooling.
  • Handle the product with care.
  • Do not disassemble, modify, or repair the product and its accessories without authorization.

3. Functional Features

  • Multi-Band Frequency: Supports FM: 65-108 MHz (RX), AM: 108-136 MHz (RX), VHF: 136-174 MHz (TX/RX), 350-390 MHz (RX), UHF: 400-480 MHz (TX/RX), 480-520MHz (RX).
  • Transmit Frequency: VHF 144-148MHz; UHF 420-450MHz.
  • RF Output: 5W/2W, dual PTT transmitter.
  • Wireless Programming: Advanced Bluetooth APP programming for easy frequency customization without cables.
  • Wireless Copy Frequency: One-click quick copy function to search and store frequencies and privacy codes from other radios.
  • Display: 1.44" TFT large screen with full keyboard and open menu operation.
  • Channel Memory: 999 channel memory with full keyboard manual frequency input, local channel storage and deletion.
  • Frequency Pairing: One-click frequency pairing for easy grouping.
  • Relay Function Settings: Configurable frequency difference, direction, and relay activation audio settings.
  • Alarm Function: Three types of alarm settings for security.
  • Channel Name Editing: Built-in input method supports local editing of channel name, receiving frequency, and transmitting frequency.
  • DTMF: DTMF encoding and decoding function, supporting 20 DTMF calls.
  • Frequency Hopping: Includes frequency hopping function.
  • Side Button Customization: Assign functions like radio, scan, sweep, voice control, flashlight, or alarm to side buttons.
  • FM Radio: FM radio function (receive frequency 78~108MHz).
  • Keypad Lock: Automatic or manual keypad lock, backlight selection.
  • Charging: Support Type-C charge for convenient charging via car, power bank, or laptop.
  • Battery Capacity: Upgraded 2200mAh battery for extended standby time.
  • Flashlight: LED spotlight for emergency use and night display.

4. Package Contents

The standard package for your Baofeng MINI 5 Walkie Talkie includes the following items:

ItemQuantity (PCS)ItemQuantity (PCS)
Radio1Lanyard1
Battery1Operation Manual1
Antenna1Belt Clip1

Note: Charger and power adapter are subject to the final configuration of the dealer. The charging instructions in this manual may not be appropriate if Type-C charging method is used.

Baofeng MINI 5 Walkie Talkie components including antenna, battery, clip, Type-C charger, and lanyard.
Figure 4.1: Standard package contents of the Baofeng MINI 5 Walkie Talkie.

5. Product Overview

Familiarize yourself with the various parts and controls of your Baofeng MINI 5 Walkie Talkie.

Two Baofeng MINI 5 Walkie Talkies displaying their screens and highlighting features like Bluetooth APP Programming, Wireless Copy Frequency, 999 Channels, Dual PTT, 2200mAh Battery, and AM/FM.
Figure 5.1: Overall view of the Baofeng MINI 5 Walkie Talkie and its main functionalities.
Baofeng MINI 5 Walkie Talkie highlighting various features like APP programming, copy frequency, 999 channels, multi-band, flashlight, CTSS/CDS, VOX, Type-C charger, 1.44 inch large screen, FM radio, and NOAA.
Figure 5.2: Key features of the Baofeng MINI 5 Walkie Talkie.
Baofeng MINI 5 Walkie Talkie demonstrating its small size and portability compared to a smartphone.
Figure 5.3: Compact and lightweight design of the MINI 5 Walkie Talkie.
Baofeng MINI 5 Walkie Talkie showing dual PTT buttons and 1.44 inch screen.
Figure 5.4: Front view of the Baofeng MINI 5 highlighting the dual PTT keys and large screen.
Baofeng MINI 5 Walkie Talkie showing Type-C charging port and charging indicator lights.
Figure 5.5: Type-C charging feature with indicator lights.
Baofeng MINI 5 Walkie Talkie demonstrating one-touch search frequency function.
Figure 5.6: One-touch search frequency steps.
Smartphone screen showing 'OLA Radio' app and 'Device Parameters' for '5R Mini' walkie talkie, indicating APP Programming.
Figure 5.7: APP Programming interface on a mobile phone.

5.1 Component Identification

Refer to the diagram below for a visual guide to the radio's components.

Detailed diagram of Baofeng MINI 5 Walkie Talkie with labeled parts: Antenna, Flashlight, Microphone, Screen, V/M-VFO/MR, OK/Menu button, A/B button, Search/Flashlight button, Up/Down button, Volume/Power Knob, Accessory Port, PTT-A Button, PTT-B Button, Type-C Charging Port, Type-C Charging indicator light, Clip.
Figure 5.8: Detailed component diagram of the Baofeng MINI 5 Walkie Talkie.
  1. Antenna
  2. SK1-Customized Function Keys/Monitor button
  3. PTT-A Button
  4. OK/Menu button
  5. V/M-VFO/MR
  6. PTT-B Button
  7. Numeric Keypad
  8. Flashlight
  9. Volume/Power Knob
  10. Screen
  11. Accessory Port
  12. Cancel/Back button
  13. ▲ Up button/▼Down button
  14. A/B
  15. Microphone
  16. LED Indicator
  17. Battery Latch
  18. Type-C Charging indicator light
  19. Type-C Charging Port
  20. Search/Flashlight button

6. Before Use

6.1 Attaching the Antenna

Turn the antenna clockwise until it is tight. To remove the antenna, turn it counterclockwise.

CAUTION:

Do not hold the radio antenna in your hand, as this will reduce the performance of the radio and the life of the antenna. Do not shake the radio with the top of the antenna in your hand, as this will degrade the performance and life of the radio antenna.

7. Basic Operations

7.1 Turning Your Radio On and Off

  • To turn your radio ON, turn the [Volume/Power] rotary knob clockwise.
  • To turn your radio OFF, turn the [Volume/Power] rotary knob counterclockwise.

7.2 Setting the Volume

  • Increase volume by turning the [Volume/Power] rotary knob clockwise.
  • To decrease volume, turn the [Volume/Power] rotary knob counterclockwise.
  • Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.

7.3 Locking or Unlocking Keypad

To avoid accidentally changing radio settings:

  1. Press and hold the [*] key to lock the keypad until the screen displays the "lock" icon.
  2. In lock mode, you can turn the intercom on and off, adjust the volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
  3. In lock mode, press and hold the [*] key to unlock the keypad until the "lock" icon is no longer displayed.

7.4 Keypad Entry

You can enter radio aliases, channel aliases, numbers, etc. using the radio's numeric keypad.

  1. To switch between input methods, press [# ↑ ] key.
  2. Press 1 to enter a special character (except in numeric input mode, where the number 1 is entered).
  3. Press 0 to enter a space (except in the numeric input mode, in which special characters are entered).

7.5 Select a Channel

  • Press the [V/M] button to toggle between VFO and channel mode.
  • Press the ▲/▼ buttons or the rotary encoder to select the desired channel.
  • Enter the channel number using the keypad (e.g., enter "064" for channel 64).

7.6 Channel Memory

In Frequency and Standby mode, you can store frequencies and parameters.

  1. Press [MENU] [3] [MENU] [1] [5]. The screen will display “MEMCH”.
  2. Press [MENU] to enter the function. Press the ▲/▼ buttons to select the channel, then press [MENU] to store it. A sound tone will confirm success.
  3. Press [EXIT] to return to standby mode.

Note: If you want to set CTCSS tones, DCS codes or the frequency offset, you must do it before storing the channel. Stored channels are displayed as CH-, other channels have no CH- display.

7.7 Delete a Channel (DEL-CH)

In VFO mode and Standby mode:

  1. Press [MENU] [3] [MENU] [1] [6]. The screen will display “DELCH”.
  2. Press [MENU] to enter the function. Press the ▲/▼ buttons or rotate the encoder to select the channel you want to delete, then press [MENU] to confirm.
  3. To return to standby mode, press [EXIT] key.

Note: Channel 1 cannot be deleted.

7.8 Main Band/Sub Band Switch

In standby mode, press the [A/B] key to toggle between the A and B bands to switch between the main/sub bands. The main band is the highlighted band. The darker displayed band is the sub-band.

7.9 VFO/Channel Switch

Press the [V/M] button to switch between VFO and channel display. VFO mode will display the ‘VFO’ icon. MR mode will display the channel serial number.

7.10 Setting the VFO Frequency

Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.

  • Operation 1: Input the VFO frequency directly with the keypad.
  • Operation 2: Press the ▲/▼ button or rotary encoder to adjust the VFO frequency in the set frequency step.

7.11 Call Service

All radios in the group must be set to the same channel and sub-code to communicate. To ensure optimal reception volume, keep the distance between the microphone and your mouth at 2.5 cm to 5 cm when transmitting.

  • Initiate a call: Select a channel, press and hold the [PTT-A] key (transmits on segment A) or [PTT-B] key (transmits on segment B). The red indicator light will be on. Speak into the microphone with normal voice tone.
  • Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light will be on.

8. Advanced Features

8.1 Emergency Alarm

Emergency alarm allows the terminal to initiate an alarm to seek help. In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.

8.2 Flashlight

In standby mode, press the preset search/flashlight key to turn the flashlight on or off.

Baofeng MINI 5 Walkie Talkie with LED flashlight illuminated, showing transparent radio night display.
Figure 8.1: LED Flashlight feature for night display.

8.3 FM Radio Function

Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1. Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. The screen displays the tuning frequency.

  • Press ▲/▼ key to search for radio channels at the preset step frequency.
  • Press the [# ↑ ] key to search for radio channels automatically. The screen displays 'SEEK...'.
  • Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
  • Press SK1 key [FM Radio] to exit radio mode.

8.4 Monitor

Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. This also allows you to adjust the volume. Release the [Monitor] key to exit.

8.5 Frequency Search (Wireless Copy Frequency)

Press the pre-programmed [SEARCH] key or press and hold search/flashlight key. The radio enters frequency search state, displaying "SEARCH...". Press [# ↑ ] key to switch the searching band (VHF/UHF, etc.). The frequency and CTCSS/DCS code will be displayed after searching is completed. Press [MENU] to save the channel.

Baofeng MINI 5 Walkie Talkie demonstrating wireless copy frequency feature between two radios.
Figure 8.2: Wireless Copy Frequency in action.

8.6 Reverse Frequency Function

Short press the [*] key in relay mode to invert the receive and transmit frequencies. The screen shows the 'R' icon. This is useful for repeater channels with frequency differences.

8.7 Talk Around Function

In repeater mode, press [*] to switch between Talkaround Mode and Repeater Mode. The screen displays 'T' and 'R' icons. In Talkaround mode, the receive frequency equals the transmit frequency.

8.8 Repeater Activation Tone

Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.

8.9 Voice-activated Transmit (VOX)

Enable VOX function to transmit automatically by voice without pressing the PTT key. To enable:

  1. In Standby status, press [MENU][2][MENU][4] to enter Vox Switch.
  2. Press [MENU][2][MENU][5] to enter Vox Level, press ▲/▼ to select VOX level (1-9). A smaller value means higher sensitivity. The 'V' icon is displayed.
  3. To turn off VOX, select OFF. The 'V' icon disappears.
  4. Press [MENU] key to save the setting and return to the upper menu.

8.10 Dual Watch

In Dual Watch mode, the radio can receive frequencies for channel A or B.

  1. Press [MENU] [2] to enter Radio Set.
  2. Press [MENU] + ▲/▼ to select "15 Dual Watch".
  3. Press [MENU] to enter Dual Watch Setting, press ▲/▼ key to select “On”.
  4. Press [MENU] to save. The 'D' icon will be displayed.
  5. To turn off, repeat steps and select "Off". The 'D' icon disappears.

8.11 Stopwatch Function

Press and hold the [MENU] key to enable the stopwatch function.

  • Press [MENU] to start.
  • Press [MENU] again to stop.
  • Press [EXIT] to exit.

8.12 Weather Radio / Scan Weather Channel (NOAA)

Your radio has a NOAA Weather Radio function to receive weather reports and scan all 10 NOAA Weather Radio channels.

  1. To turn NOAA Weather Scan on, press and hold the [0] key for 3 seconds. The "cloud" icon appears, and the radio goes to Weather band mode.
  2. Press and hold the [# ↑ ] key for 3 seconds to start automatic scanning of all 10 channels.
  3. After stopping NOAA weather scan, manually select the weather channel by pressing the ▲ or ▼ key.
  4. To exit Weather Radio broadcast mode, press the search/flashlight key or [PTT] key.

Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

10. Wireless Programming

The Baofeng MINI 5 supports wireless programming via a mobile application. This feature allows for easy customization and adjustment of frequencies without the need for physical cables.

10.1 APP Programming

You can program the radio wirelessly by installing the "OLA Radio" APP on your smartphone. Refer to the official PDF manual for QR codes to download the Android or iOS app.

Smartphone screen showing 'OLA Radio' app and 'Device Parameters' for '5R Mini' walkie talkie, indicating APP Programming.
Figure 10.1: APP Programming interface on a mobile phone.

After opening the APP, allow Bluetooth and location services. Select the "5Rmini Series" model, connect the radio, and click "Walkie-talkie". A confirmation message will indicate successful connection.

10.2 Wireless CPS Operations

To enter Wireless CPS, press [MENU] + [4]. Then, press [MENU] + ▲/▼ to select "On". The "Bluetooth" icon will be displayed on the screen.

  • Read the radio data: After reading the frequency, click to enter program details. You can program channel information, frequency mode, and optional functions.
  • Save Profile: Save the programmed profile as a new profile.
  • Write data to radio: Click home page, select program, click 'Write' to enter write frequency. The radio will restart automatically after writing.

11. Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care. Following these suggestions will help you maintain your product for many years:

  • Do not attempt to open the radio for any reason. Precision mechanics and electronics require specialized equipment. Unauthorized opening voids the warranty.
  • Do not store the radio under direct sunlight or in hot areas. High temperatures can shorten the life of electronic devices and warp plastics.
  • Do not store the radio in dusty and dirty areas.
  • Keep the radio dry. Rainwater or dampness will corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
  • Do not transmit without an antenna.

11.1 Battery Maintenance

Charging Precautions:

  • Do not charge or replace your battery in locations with fuels, chemicals, or explosive materials.
  • Do not charge a wet battery. Dry it with a soft, clean cloth first.
  • Do not charge a battery that is deformed, leaking, or overheated.
  • Do not charge your battery with an unauthorized charger.
  • Do not charge your battery in areas with strong radiation.
  • Avoid overcharging, as it may shorten battery life.

Charging Instructions:

When using the terminal for the first time, a low battery warning may occur. It is recommended to turn off the radio during charging. The battery's LEDs indicate the charging status:

Indicator LightCharging Status
Red light is always onCharging
Green light is always onCharging complete
  • It is recommended to charge the battery between 5°C~40°C.
  • To charge a battery attached to the product, turn it off for a full charge.
  • Do not remove the battery or unplug the power cord during charging to ensure a smooth process.

12. Troubleshooting

This section provides guidance on common issues you might encounter with your Baofeng MINI 5 Walkie Talkie.

  • Programming Errors: If errors occur during programming, ensure you read the factory software data first, then rewrite with your desired frequencies. Verify your programming complies with FCC (or EU) licensing.
  • Unusual Smell or Smoke: If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery. Do not attempt to use it again and seek professional assistance.
  • Reduced Performance/Antenna Issues: Do not hold the radio antenna in your hand or shake the radio by the antenna, as this can reduce performance and damage the antenna. Ensure the antenna is securely attached.
  • Battery Not Charging: Check if the battery is wet (dry it first). Ensure the charger is authorized and the charging environment is within 5°C~40°C.
  • Keypad Locked: If the keypad is locked, press and hold the [*] key to unlock it.

13. Technical Specifications

General
Receiver FrequencyFM 76-108 MHz; VHF 136-174MHz, UHF 400-520MHz, 350-390MHz
Transmission FrequencyVHF 144-148MHz, UHF 420-450MHz
Channel Spacing25.0KHz(Wide)/12.5KHz(Narr)
Memory Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Dimensions108mm×52mm×37mm (No antenna)
Weight200g (Battery pack included)
Transmission current≤1600mA
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna impedance50 Ohm

Note: All specifications may be modified without prior notice or liability.

14. User Tips

  • Battery Life: The upgraded 2200mAh battery provides extended standby time. To maximize battery life, consider enabling the Power Save feature in the Radio Settings menu.
  • Easy Programming: Utilize the Bluetooth APP Programming feature for convenient frequency customization. This eliminates the need for complex software and cables.
  • Quick Frequency Copy: For quick setup with another radio, use the Wireless Copy Frequency function. This allows you to easily match frequencies and privacy codes.
  • Emergency Preparedness: Familiarize yourself with the Emergency Alarm and NOAA Weather Radio functions for safety in various situations.
  • Portability: The MINI 5 is lightweight (only 200g) and features a portable back clip, making it easy to carry for outdoor activities.

15. Warranty and Support

The accuracy and completeness of the contents of this manual are diligently compiled. However, the manufacturer reserves the right to change the design and specifications of the product without prior notice due to continuous technological development.

Unauthorized opening or modification of the transceiver will void the warranty.

For any questions, technical support, or warranty claims, please contact your original point of purchase or the manufacturer's customer service.

A PDF version of the user manual is available for download: User manual (PDF)

Print version: 5R Mini_V1.0

Manufacturer: BAOFENG

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.