Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the tool, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- Do not place the device on any unstable surface.
- Never leave the device unattended during charging process. The device must be placed on a non-flammable surface during charging.
- Handle the device with care. If the device is dropped, check for breakage and any other conditions that may affect its operation.
- Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
- Keep the tool dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the device when necessary.
- People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
- Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
- This tool contains an internal Lithium Polymer battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, pierce or dispose of the battery in fire or water.
- This product is not a toy. Do not allow children to play with or near this item.
- Do not expose the device to rain or wet conditions.
1. Introduction
1.1 Vehicle Coverage
This tool is specially designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN). It is required by EPA that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant and this includes all American, Asian and European vehicles.
A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label. It is located under the hood or by the radiator of most vehicles. If the vehicle is OBD II compliant, the label will designate "OBD II Certified".
Government regulations mandate that all OBD II compliant vehicles must have a "common" 16-pin Data Link Connector (DLC).
1.2 On-Board Diagnostics (OBD) II
The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions, which will offer three pieces of such valuable information:
- Whether the Malfunction Indicator Light (MIL) is commanded “on” or “off”;
- Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
- Readiness Monitor status.
1.3 OBD II Definitions
The following terms and their definitions are related to OBD II systems. Read and reference this list as needed to aid in the understanding of OBD II systems.
- EOBD:
- European On-Board Diagnostics. Essentially the same as OBD II, with the same Data Link Connector and Communication Protocols.
- Communication Protocols:
- Allows different systems and sensors in a vehicle to communicate. There are currently five protocols: CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
- PCM (Powertrain Control Module):
- The OBD II accepted term for the vehicle's "on-board computer." In addition to controlling the engine management and emissions systems, the PCM also participates in controlling the powertrain (transmission) operation. Most PCMs also have the ability to communicate with other computers on the vehicle (ABS, ride control, body, etc.).
- DLC (Data Link Connector):
- The 16-cavity connector on the vehicle that allows communication between the computer system and the diagnostic tool.
- MIL (Malfunction Indicator Light):
- The vehicle's “Check Engine” warning light that activates when a DTC is stored.
- DTC (Diagnostic Trouble Code):
- A code stored in the computer system's memory, which helps to identify the fault condition that is causing the MIL to activate.
- Freeze Frame Data:
- Operating conditions that are stored when a DTC is stored.
- PID (Parameter Identification Data):
- Data returned by the vehicle's control modules to the diagnostic tool.
- Monitors:
- “Diagnostic routines” programmed into the PCM to run diagnostic tests and monitor emissions-related components.
- Enabling Criteria:
- Vehicle-specific events or conditions that must occur within the engine before various monitors will set or run.
- Trip:
- For a particular Monitor, requires that the vehicle is being driven in such a way that all the required “Enabling Criteria” for the Monitor to run and complete its diagnostic testing are met.
- Drive Cycle:
- A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the "ready" condition.
- Warm-up Cycle:
- Vehicle operation after an engine off period where engine temperature rises at least 40°F (22°C) from its temperature before starting, and reaches at least 160°F (70°C).
- Fuel Trim (FT):
- Feedback adjustments to the base fuel schedule. Short-term FT refers to dynamic adjustments, Long-term FT to gradual adjustments.
1.4 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are stored by the on-board computer diagnostic system in response to a problem. These codes identify a particular problem area and provide a guide as to where a fault might be occurring. DTCs consist of a five-digit alphanumeric code. The first character (a letter) identifies the control system, the second character (a number 0-3) and the remaining three characters (a hex character 0-9 or A-F) provide additional information on the DTC origin and operating conditions.
1.5 Location of the Data Link Connector (DLC)
The DLC is typically a 16-pin connector where diagnostic code readers interface with the vehicle's on-board computer. It is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary. If the DLC cannot be found, refer to the vehicle's service manual for the location.

2. Product Description
2.1 Components & Controls

- Charging LED: Red indicates charging, Green indicates fully charged.
- LCD: Displays test results and interface.
- Charging port: For charging the tool via charging cable.
- DB-15 diagnostic connector: Connects the tool to the vehicle’s DLC.
- Power button: Turns the tool on/off.
- HOME button: Press to return to the home (Job menu) screen.
- Selection buttons: Move cursor up/down/left/right for selection or page navigation.
- OK button: Confirms a selection or action.
- Return button: Exits the current program or returns to the previous screen.
2.2 Technical Specifications
- Screen: 5" touch screen (1280*720P)
- Battery: 3.7V/6000mAh (Built-in Lithium Polymer)
- Operating System: Android 8.1
- RAM: 2G
- ROM: 32GB (system displays 25.9GB)
- OBDII input voltage range: 9V~18V
- Charging via: DC 5V charging cable or diagnostic cable through vehicle's DLC
- Diagnostic cable Length: 1.2M
- Dimension: 250*175*75 mm
- Working temperature: -10 to 50℃ (14 to 122℉)
- Storage temperature: -20 to 70℃ (-4 to 158℉)
- Communication Interface: OBD-II
- Wireless Support: Wifi
- Software Update: Yes, Lifetime Free Update Via Wifi
- Hardware Version: 2026 Version
- Software Version: 2026 Version
- Certification: CE
- Warranty: 2 Year Warranty
2.3 Accessories Checklist
For detailed accessory items, please consult from the seller.
- Diagnostic scanner (main unit)
- OBD II diagnostic cable
- Charging cable
- User manual
- Carrying bag

3. Setup (Initial Use)
3.1 Charging
There are two charging methods available:
- Via Charging Cable: Plug one end of the included charging cable into the charging port of the tool, and the other end to an external charger or an AC outlet with USB ports.
- Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle's DLC.
Once the charging LED illuminates solid green, it indicates that the battery is fully charged.
3.2 Getting Started
If it is the first time you have used this tool, you need to make some system settings:
- Press the [Power] button to power it on.
- The screen displays a welcome page. Tap “Start” to go to next step.
- Choose the desired system language, and tap "Next".
- Choose the desired time zone, and tap “Next” to enter the WLAN setup page.
- Slide the switch to ON, the system starts searching for all available wireless LANs. Choose the desired WLAN access point / network.
- If the network you chose is open, you can connect directly. If the selected network is encrypted, you have to enter the right security key (network password).
- After the network connection is done, tap “Next Step" to configure email address. Input the email address, and tap "Next Step” to go to next step. (Note: It is strongly recommended to fill in a valid email address. Once configured, the system will automatically send the diagnostic report to your email box every time a complete Auto-Detect process is successfully finished.)
- Carefully read all terms and conditions of the user agreement, check the box before the "Agree to all the above terms”, and tap “OK” to finish the sign-up process and navigate to the Job Menu.
4. Operating Instructions
4.1 Connection
- Turn the ignition off.
- Locate the vehicle's 16-pin Data Link Connector (DLC).
- Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end to the DB-15 diagnostic connector of the tool, then tighten the captive screws.
- Turn the ignition on. Engine can be off or running.
Notes:
- A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the diagnostic cable.
- The cable connector is keyed and will only fit one way. If you have problems connecting the cable connector to the DLC, rotate the connector 180° and try again.
4.2 System Diagnosis
This function is specially designed to diagnose electronic control systems of single vehicle model. For CRP123i V2.0/129i V2.0, only four vehicle systems with basic diagnostic functions are supported. For CRP123E PLUS/129E PLUS, all vehicle systems with basic diagnostic functions are supported.
4.2.1 Smart Diagnosis (Auto-Detect)
This function allows you to quickly access the electronic control systems of the vehicle via decoding the VIN, without manual step-by-step menu selection. After connection, turn the ignition key on and the system enters auto-detect mode.
Notes:
- Please make sure the “Automatic detection on connect” in “Settings" is set as ON.
- A highly stable and solid network connection is recommended for successful VIN access.
A. Successful VIN Access: Once the system successfully obtains the VIN (Vehicle Identification Number) information of the currently identified vehicle, it will continue scanning the vehicle systems. After the scanning is complete, a diagnostic report will be automatically generated and sent to your email box (if bound).
B. Failed VIN Access: If the tool fails to access the VIN information, the screen will display an input prompt. Input the VIN, and tap “OK”, the system will decode the VIN data automatically, and continue the Smart Diagnosis procedure if successful. Otherwise the system will enter the Manual Diagnosis mode.
4.2.2 Manual Diagnosis
If the tool cannot obtain the VIN information, you can also perform vehicle diagnosis manually. In this mode, you need to execute the menu-driven command and then follow the on-screen instruction to proceed.
Notes:
- Before diagnosing, please make sure the diagnostic program corresponding to the specific vehicle model has been installed on your tool.
- The diagnostic menu may vary by the vehicle's make, model and year.
To diagnose a vehicle manually:
- Select "Diagnose" from the Job Menu.
- Select Vehicle Manufacturer.
- Select Vehicle Model.
- Select Scan Mode (Automatic System Detection or Manual System Detection).
- Select Test Function (Read Version Information, Read Fault Code, Clear Fault Code, Read Data Stream).
4.2.2.1 Health Report (Quick Test)
This function enables you to quickly access all the electronic control units of the vehicle and generate a detailed report about vehicle health. Tap "Health Report" on the test item selection screen, the system starts scanning the ECUs. Once the scanning is complete, a report will appear showing fault codes (red cross) or OK status (green tick) for each system.
4.2.2.2 System Scan
This option allows you to quickly scan which systems are installed on the vehicle.
4.2.2.3 System Selection
This option allows you to manually select the test system and function step by step. Tap "System Selection” on the test item selection screen, and tap the desired system (e.g., "Engine”) to enter the test function selection screen.
A. Read Fault Code: Displays detailed information of DTC records retrieved from the vehicle's control system. Tap "Read Fault Code” on the test function selection screen to view the diagnostic result.
B. Clear Fault Code: Erases codes from the vehicle after retrieving codes and performing repairs. Ensure the vehicle's ignition key is in the ON position with the engine off before operation. Clearing DTCs does not fix the underlying problem.
C. Read Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU. Tap "Read Data Stream" on the test function selection screen. You can select specific items, combine up to 4 live data streams for graphing, and record/review data.
4.3 OBDII Diagnosis (Full 10 Modes)
This option provides a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related. After connecting the tool to the vehicle's DLC and tapping "OBD II" on the Job menu, the tool will automatically detect the communication protocol and display the Monitor Status.

- Read Codes: Shows detailed descriptions of Diagnostic Trouble Codes (DTCs).
- Erase Codes & Reset: Turns off Check Engine Light (MIL), clears codes, and resets monitors.
- Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and storing freeze frame data.
- I/M Readiness Status: Shows whether emissions-related systems are operating properly and are ready for inspection and maintenance testing.
- Read Live Data Stream: Displays continuous data stream from a vehicle in live graphic (waveform) display.
- View Freeze Frame Data: Checks vehicle conditions recorded by the on-board computer when an emission-related fault occurs.
- O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results.
- On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems that are not continuously monitored.
- Read Vehicle Information: Displays VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).
- Component Test: Certain vehicle components can be actuated by commands from the scanner to test their operability.
4.4 History
The tool records every detail of a diagnostic session. The History function provides direct access to previously tested vehicles, allowing users to resume from the last operation without starting from scratch. Diagnostic records are listed in date sequence.
- Tap a vehicle model to view details of the last diagnostic report.
- To delete specific diagnostic history, select it and tap "Delete". To delete all records, tap “Select All” then “Delete".
- Tap "Quick access" to directly navigate to the function selection page of the last diagnostic operation.
4.5 Reset Functions (7 Hot Reset Services)
The tool offers coding, reset, relearn, and other service functions to help vehicles return to functional status after repair or replacement. Available service functions are subject to change without prior written notice. Check for updates regularly.

There are two methods to reset service lamp: Manual reset or Auto reset. Auto reset sends commands from the tool to the vehicle's ECU. Manual reset requires users to follow on-screen instructions to select appropriate execution options, enter correct data, and perform necessary actions.
To perform resetting:
- Select "Reset" from the Job Menu.
- Choose the desired service function.
- Select the desired car brand.
- Select the reset mode (varies by vehicle).
- Follow the on-screen instructions to proceed.
Oil Lamp Reset
Resets the Oil Life Reminder and switches off the Oil Light after engine oil replacement, ensuring driving safety.
EPB Reset (Electronic Parking Brake)
Used when brake pads or wear sensors are replaced, the brake pad indicator lamp is on, or the servo motor is replaced. Simplifies the braking process.
Steering Angle Calibration (SAS Reset)
After replacing the steering angle position sensor, performs SAS calibration to clear fault memories, set the steering angle to zero, and turn off the steering wheel warning light.
Battery Matching (BMS Reset)
Required when the main battery or battery monitoring sensor is replaced. Clears original low battery fault information and performs battery matching.
ABS Bleeding
Performs brake operation to remove air from the brake fluid pipeline when changing brake fluid, allowing one person to complete the task.
DPF Regeneration (Diesel Particulate Filter)
Clears PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode to stabilize the filter.
Throttle Relearn (ELEC.THROTTLE RLR)
Makes initial settings to throttle actuators for smooth driving after the throttle body has been replaced or cleaned.
5. Maintenance & Data Management
5.1 Update
If new software or APK can be updated, a numeric indicator will display on the "Upgrade" module on the Job menu. Use this option to keep the tool synchronized with the latest version.
Notes:
- To enjoy more functions and better service, it is strongly suggested to update on a regular basis.
- This function requires a stable network connection.
Update Diagnostic Software
Tap "Upgrade" on the Job menu to enter the update center. By default, all diagnostic software is selected. To deselect certain software, tap “Unselect" and check the box next to the vehicle model. Tap "Update" to start downloading. It may take several minutes. To pause, tap “Stop”; to resume, tap “Continue”. If network connection fails, tap “Retry”. Once download is finished, software packages will be installed automatically.
Renew Software Subscription
For Creader Professional 123E PLUS/129E PLUS, the preset diagnostic software can be free to use and update for two years. After it expires, it will become disabled. In this case, renew your subscription to unlock it. (Note: Before performing this operation, users need to purchase a Subscription Renewal Card from the seller.) When the software is due, a "Renew” button will appear at the bottom of the screen. Tap it and follow the onscreen instructions to proceed.
5.2 Data Management
The "Data" module includes several functions for managing diagnostic information:
- Diagnostic Report: Stores running parameters or waveform graphs recorded by the user.
- Diagnostic Record: Stores all diagnostic reports generated during vehicle diagnosis.
- DTC Library: Helps to get details of DTCs, simplifying the diagnostic process.
- DLC (Data Link Connector) Location: Helps to find the location of the vehicle's DLC.
- Feedback: Allows sending feedback on diagnostic problems for further analysis and troubleshooting.
- Image: Allows viewing and managing all screenshots created during vehicle diagnostic work.
- Firmware Fix: Used to upgrade and fix diagnostic firmware. Do not cut power or switch interfaces during fixing.
6. Troubleshooting & FAQs
6.1 Frequently Asked Questions (FAQ)
The "FAQ" module provides a list of frequently asked questions for easier retrieval.
If you encounter issues, please refer to the following common questions:
- Q: The tool does not power on.
A: Ensure the battery is charged. Connect the tool to a power source using the charging cable or to the vehicle's DLC. - Q: The tool cannot connect to the vehicle.
A: Verify the DLC cable is securely connected to both the tool and the vehicle's DLC port. Ensure the ignition is on. Check if the vehicle is OBD II compliant. - Q: Diagnostic report is not sent to email.
A: Check your network connection in "Settings". Ensure a valid email address is configured in the initial setup. - Q: The tool does not support my vehicle.
A: The tool supports 57+ car brands and 10000+ vehicle models (1996 and newer OBD2/CAN cars). For specific compatibility, check the vehicle's VECI label for "OBD II Certified". If you have a Mahindra 2018, please ensure it is OBD II compliant. - Q: How to clear fault codes?
A: After performing necessary repairs, navigate to the "Clear Fault Code" function within the System Diagnosis or OBDII Diagnosis menu. Ensure the ignition is on and the engine is off.
7. Specifications
| Attribute | Value |
|---|---|
| Screen | 5" Touch Screen (1280*720P) |
| Battery | 3.7V/6000mAh |
| Operating System | Android 8.1 |
| RAM | 2G |
| Memory (ROM) | 32GB (system displays 25.9GB) |
| OBD II Input Voltage Range | 9V~18V |
| Charging via | DC 5V charging cable |
| Diagnostic Cable Length | 1.2M |
| Dimension | 250*175*75 mm |
| Working Temperature | -10 to 50℃ (14 to 122℉) |
| Storage Temperature | -20 to 70℃ (-4 to 158℉) |
| Communication Interface | OBD-II |
| Wireless Support | Wifi |
| Software Update | Lifetime Free Update Via Wifi |
| Hardware Version | 2026 Version |
| Software Version | 2026 Version |
| Certification | CE |
| Warranty | 2 Year Warranty |
| Supported Protocols | EOBD/OBDII / KOBD/JOBD, DOIP, CANFD |
| Supported Systems | Engine, Transmission, ABS, SRS (4 System Diagnostic) |
| Reset Services | OIL/SAS/BRAKE/DPF/INJEC/BMS/ETS RESET (7 Reset Service) |
| Special Features | Wifi, Auto VIN Scan, Battery Test, Health Report Record, Playback and Print |
| Supported Car Brands | 57+ Car Brands, 10000+ Vehicles Models (Asia, Europe, USA) |
| Supported Languages | English, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Spanish, Traditional Chinese |
| Tips | Only supports 12V Car, not 24V Truck |
8. Warranty & Support
8.1 Warranty
This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.
LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
8.2 Customer Service
If you have any questions on the operation of the unit, please contact the seller, or contact LAUNCH TECH CO., LTD:
- Website: www.x431.com, www.cnlaunch.com
- Phone: +86 755 2593 8674
- Email: DOD@cnlaunch.com
Statement: LAUNCH reserves the rights to make any change to this manual without notice. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable. If you have any question, please contact local dealer or LAUNCH TECH CO., LTD., LAUNCH does not bear any responsibility arising from misunderstandings.
9. User Tips
- Vehicle Compatibility: Always verify your vehicle's OBD II compliance, especially for older models (pre-1996) or specific brands like Mahindra. Check the Vehicle Emissions Control Information (VECI) Label under the hood for "OBD II Certified" status.
- Network Connection for Updates: Ensure a stable Wi-Fi connection when performing software updates or renewing subscriptions to avoid interruptions.
- Email for Reports: Configure a valid email address during initial setup to automatically receive diagnostic reports, which can be very helpful for record-keeping and sharing with mechanics.
- Troubleshooting Fault Codes: Remember that clearing fault codes does not fix the underlying problem. Always diagnose and repair the cause of the fault before clearing codes to prevent them from reappearing.
- Battery Voltage Monitoring: Utilize the real-time battery voltage display to monitor your vehicle's battery health, which can help prevent unexpected breakdowns.