PYM PYM200

Contents

PYM200 Multi-Blade Rip Saw Instruction Manual

Furniture Factory Woodworking Log Wood Cutting Equipment

1. Introduction

This manual provides essential information for the safe and efficient operation, setup, and maintenance of the PYM200 Multi-Blade Rip Saw. Designed for furniture factories and woodworking operations, this circular gang saw equipment is engineered for precise and high-efficiency log cutting. Please read this manual thoroughly before operating the machine to ensure proper usage and to prevent injury or damage.

2. Safety Instructions

WARNING: Failure to follow these safety instructions may result in serious injury or death.

  • Always wear appropriate personal protective equipment (PPE), including safety glasses, hearing protection, and work gloves.
  • Ensure the machine is properly grounded and connected to the correct power supply (380V or 220V as specified).
  • Never operate the machine with guards removed or damaged. The thickened cover is designed for safer use.
  • Keep hands and loose clothing away from moving parts, especially the saw blades and feeding mechanism.
  • Ensure the work area is clear of obstructions and well-lit.
  • Only trained and authorized personnel should operate this equipment.
  • Before performing any maintenance or adjustments, always disconnect the machine from the power source.
  • Utilize the anti-rebound device for wood to prevent kickback during operation.
  • Do not overload the machine; adhere to the specified log diameter and length limits.

3. Product Overview

The PYM200 Multi-Blade Rip Saw is a robust and efficient machine designed for cutting logs into planks. Key features include:

  • Multi-Blade Design: Ensures energy-saving operation and low waste, producing flat and smooth sawing surfaces.
  • Frequency Control Switch: Allows for free control of the feeding speed (0-10m/min) for optimal cutting.
  • Anti-Rebound Device: Enhances safety by preventing wood from rebounding in the opposite direction.
  • V-shaped Feeding Device: Specifically designed for round logs, increasing friction and providing powerful grip for stable feeding. Capable of cutting logs with a small diameter of 60mm.
  • Thickened Cover: Provides enhanced safety during operation.
  • Spindle Water Cooling: Ensures optimal performance and extends the life of the saw blades.
Front view of the PYM200 Multi-Blade Rip Saw
Figure 1: Front view of the PYM200 Multi-Blade Rip Saw.
Labeled diagram of PYM200 saw components
Figure 2: Key components of the PYM200 Multi-Blade Rip Saw, including the switch controller, thickened cover, anti-rebound device, and V-shaped feeding device.
Detailed features of the PYM200 Multi-Blade Rip Saw
Figure 3: Detailed views of the control panel, multi-blade setup, V-shaped conveyor chain, and overall benefits of the machine.

4. Specifications

The following table outlines the technical specifications for the PYM series Multi-Blade Rip Saws:

Feature PYM200 PYM250 PYM-300 PYM-350 PYM-400
Sawing Log Diameter 60mm-200mm 80-250mm 100-300mm 100-350mm 120-400mm
Sawing Log Length 650-4000mm 700-4000mm 750-4000mm 800-4000mm 900-4000mm
Spindle Speed 3300r/min 3300r/min 2500r/min 2300r/min 2300r/min
Main Motor Power 22KW*2 (44KW total) 22KW+30KW 30KW+37KW 37KW*2 45KW*2
Feeding Motor 1.5KW*2 1.5KW*2 1.5KW*2 1.5KW*2 1.5KW*2
Feed Speed (Frequency Control) 0-10m/min 0-10m/min 0-10m/min 0-10m/min 0-10m/min
Saw Blade Diameter 305mm 355mm 405mm 455mm 500mm
Spindle Diameter 50mm 50mm 70mm 70mm 70mm
Cooling Mode Spindle water cooling
Overall Dimension (L*W*H) 3420*1550*1530mm 3500*1550*1530mm 3800*1680*1600mm 3860*1680*1600mm 3900*1680*1600mm
Machine Weight 2100kg 2500kg 2800kg 3200kg 3400kg
Certification CE
DIY Supplies Electrical
Key Selling Points Easy To Operate
Machinery Test Report Provided
Video Outgoing-Inspection Provided
Core Components Motor
Remarks Optional Accept customization

5. Setup

5.1 Unpacking and Placement

  • Carefully unpack the machine, ensuring all components are present and undamaged.
  • Place the saw on a stable, level surface capable of supporting its weight (2100kg for PYM200).
  • Ensure adequate clearance around the machine for safe operation, log feeding, and sawdust removal.

5.2 Electrical Connection

  • Connect the machine to a suitable electrical supply (380V or 220V, 44KW total power for PYM200) as indicated on the machine's rating plate.
  • Ensure all electrical connections are secure and comply with local electrical codes.
  • Verify proper grounding to prevent electrical shock.

5.3 Blade Installation (if not pre-installed)

  • With the power disconnected, open the thickened cover.
  • Carefully install the saw blades (305mm diameter for PYM200) onto the spindle (50mm diameter for PYM200), ensuring they are correctly oriented and securely fastened.
  • Close and secure the cover before restoring power.

5.4 Water Cooling System

  • Connect the spindle water cooling system as per the manufacturer's instructions to ensure continuous cooling during operation.
  • Verify that the water flow is adequate and free of leaks.

6. Operation

6.1 Pre-Operation Checks

  • Ensure all safety guards are in place and functioning correctly.
  • Check that the saw blades are sharp, clean, and properly installed.
  • Verify the water cooling system is active and supplying water to the spindles.
  • Confirm the work area is clear and logs are ready for processing.

6.2 Starting the Machine

  • Turn on the main power switch.
  • Engage the main motor(s) using the control panel. Allow the blades to reach full operating speed before feeding logs.

6.3 Feeding Logs

  • Place logs onto the V-shaped feeding device, ensuring they are within the specified diameter (60mm-200mm for PYM200) and length (650mm-4000mm for PYM200) limits.
  • Use the frequency control switch to adjust the feeding speed (0-10m/min) according to the log type and desired cut quality. Start with a slower speed and gradually increase as needed.
  • Ensure logs are fed straight and consistently to prevent jamming or uneven cuts. The anti-rebound device will help maintain control.

6.4 Stopping the Machine

  • Once cutting is complete, stop the log feeding mechanism.
  • Allow the saw blades to come to a complete stop before turning off the main motor(s).
  • Turn off the main power switch and disconnect from the power source for extended periods of inactivity or maintenance.

7. Maintenance

Regular maintenance is crucial for the longevity and safe operation of your PYM Multi-Blade Rip Saw.

7.1 Daily Maintenance

  • Clean sawdust and debris from the machine, especially around the blades and feeding mechanism.
  • Check saw blades for sharpness and damage. Replace or sharpen as needed.
  • Inspect the water cooling system for proper flow and leaks.
  • Verify all safety guards are securely in place.

7.2 Weekly/Monthly Maintenance

  • Lubricate all moving parts, bearings, and chains according to the lubrication schedule (refer to specific lubrication points on the machine).
  • Inspect electrical connections for wear or damage.
  • Check the tension of the V-shaped conveyor chain.
  • Ensure all bolts and fasteners are tight.

7.3 Long-Term Storage

  • Thoroughly clean the entire machine.
  • Apply a rust preventative to all exposed metal surfaces.
  • Store in a dry, protected environment.

8. Troubleshooting

This section provides solutions to common issues you might encounter.

Problem Possible Cause & Solution
Machine does not start
  • No power supply: Check main power connection and circuit breaker.
  • Emergency stop engaged: Reset the emergency stop button.
  • Safety guards open: Ensure all covers and guards are properly closed.
Logs not feeding smoothly
  • V-shaped conveyor chain dirty or worn: Clean or replace the chain.
  • Feeding speed too low: Increase feeding speed using the frequency control.
  • Log diameter outside specified range: Ensure logs meet specifications.
Poor cutting quality (uneven, rough surface)
  • Dull or damaged saw blades: Replace or sharpen blades.
  • Incorrect feeding speed: Adjust speed for optimal cutting.
  • Log not stable during feeding: Ensure logs are securely placed and the anti-rebound device is functioning.
Overheating of spindles/blades
  • Water cooling system malfunction: Check water supply, pump, and lines for blockages or leaks.
  • Blades are dull: Sharpen or replace blades to reduce friction.

If the problem persists after attempting these solutions, please contact customer support.

9. User Tips

No specific user tips from reviews or Q&A were available at the time of this manual's creation. However, general best practices for woodworking machinery include:

  • Always perform a quick visual inspection of the machine before each use.
  • Keep spare saw blades on hand to minimize downtime.
  • Regularly clear sawdust accumulation to prevent fire hazards and maintain machine performance.
  • Familiarize yourself with the emergency stop procedure.

10. Warranty and Support

The PYM200 Multi-Blade Rip Saw comes with a 1-Year Warranty from the date of purchase, covering manufacturing defects and malfunctions under normal operating conditions.

For technical support, spare parts, or warranty claims, please contact your supplier or the manufacturer directly.

Contact Information:

  • WhatsApp: +86 16686596252
  • Email: plxxlyx01@163.com

Please have your model number (PYM200) and purchase date ready when contacting support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.