RADIOMASTER TX16S MK3

Contents

RadioMaster TX16S MK3 ELRS Transmitter User Manual

Model: TX16S MK3 | Brand: RadioMaster

1. Introduction

Thank you for choosing the RadioMaster TX16S MK3, a versatile remote control system featuring dual-band capabilities with 2.4GHz and Sub-G Gemini-Xrossband technology. Whether you're a beginner or a seasoned professional, the TX16S MK3 is designed to meet your needs, offering precision, flexibility, and reliability.

The TX16S MK3 is compatible with a wide range of applications. Powered by the robust EdgeTX platform, the TX16S MK3 is ready for seamless integration with your projects.

This manual provides essential information for safe and optimal use. Please read it carefully before operating your new remote.

2. Safety Information

WARNING: Radio control models often feature powerful motors and sharp spinning propellers. Always exercise extreme caution when working with models. Ensure power is disconnected from your models and remove propellers when performing maintenance.

Do not operate the TX16S MK3 remote control system under the following conditions:

  • In severe weather or strong windy conditions, such as rain, hail, snow, storms, or electromagnetic environments.
  • In any situation where visibility is limited.
  • In areas where people, property, high-voltage power lines, public roads, vehicles, or animals may be present.
  • If you feel tired or unwell, or under the influence of drugs or alcohol.
  • If the remote control or model appears damaged or is not working properly.
  • In areas with high 2.4GHz and Sub-G interference or where these radio frequencies are prohibited.
  • When the radio's battery voltage is too low to be used.
  • In areas where local regulations prohibit the use of aviation models.

3. Package Contents

The TX16S MK3 package includes the following items:

  • 1 * TX16S MK3 Radio Controller
  • 1 * TX16S MK3 Signature Carry Case
  • 1 * 18650 Battery Tray
  • 2 * Replacement Shoulder Panels
  • 1 * Type-C Cable
  • 1 * Screen Protector
  • 1 * 1.5mm Hex Wrench
  • 4 * Low Tension Gimbals Springs
  • 2 * Gimbal Stick Set Screws
  • 1 * Nylon Neck Strap (Lanyard)
  • 1 * RadioMaster Sticker Set
  • 1 * TX16S MK3 Manual
  • 1 * Inventory Card
Diagram showing all items included in the RadioMaster TX16S MK3 package.
Figure 3.1: Package Contents. Includes the TX16S MK3 radio, carry case, battery tray, shoulder panels, cables, screen protector, tools, springs, stick screws, lanyard, stickers, manual, and inventory card.

4. Product Overview

The RadioMaster TX16S MK3 features a comprehensive control layout and advanced components for precise operation.

4.1 Control Layout

Detailed diagram of the TX16S MK3 control layout, front and rear views, labeling all switches, gimbals, buttons, and ports.
Figure 4.1: TX16S MK3 Control Layout. This diagram illustrates the placement and labeling of all controls including dials (S1, S2), 3-position switches (SB, SA, SE, SC, SD, SG), momentary switch (SH), 2-position switch (SF), sliders (RS, LS), gimbals (Left, Right), buttons (SYS, RTN, PAGE>, PAGE<, TELE, Power, MDL, 6 Pos), trim buttons (T1-T6), scroll wheel, microphone, and various ports (DSC Trainer, USBC, Headphone Jack, SMA).

Key controls include:

  • Gimbals: V6 CNC Hall Gimbals with quad precision bearings for unparalleled stick feel. Customizable RGB lighting and external adjustments for travel, centering, and tension.
  • Switches: Multiple 2-position, 3-position, and momentary switches (SA, SB, SC, SD, SE, SF, SG, SH) for various functions.
  • Dials & Sliders: S1, S2 dials and RS, LS sliders for fine adjustments.
  • Buttons: SYS, RTN, PAGE>, PAGE<, TELE, Power, MDL, and 6-position buttons for navigation and control.
  • Ports: DSC Trainer Port, USB-C Port, Headphone Jack, SMA Port, External JR Bay, SD Card Slot.

4.2 Key Features

  • High-Performance MCU: Powered by the STM32 H7 chip for maximum processing power.
  • Touchscreen Display: 5-inch, 800 x 480 IPS touchscreen with vivid colors and sharp detail.
  • Internal RF Module: Dual-band Gemini 2.4GHz and Sub-G 900MHz ExpressLRS system with dual LR1121 transceivers.
  • Smart Balance Battery Circuit: Maximizes battery efficiency and longevity.
  • Powerful Cooling System: Low-noise, high-output fans and an aluminum heat sink.
  • Dual Foldable Antennas: Compact and easy to store without compromising signal strength.
  • Built-in Motion Sensor: Allows triggering switches, pan/tilt cameras, or telemetry callouts by tilting the radio.
  • Single USB Type-C Port: Used for data transmission, simulator connection, and charging.
Close-up of V6 CNC Hall Gimbals with RGB lighting and adjustment points.
Figure 4.2: V6 CNC Hall Gimbals. Features quad precision bearings, customizable RGB lighting, and external adjustments for travel, centering, and tension.
Side view highlighting modular features like shoulder switch panels, neck strap, external module support, anti-slip grip, and microphone.
Figure 4.3: Modular Design. Shows replaceable shoulder switch panels, neck strap attachment, external module support, anti-slip back grip, and built-in microphone.
Diagram illustrating the twin high-performance dual-band antennas.
Figure 4.4: Dual-Band Antennas. Illustrates the twin high-performance dual-band antennas for exceptional signal quality.
Diagram showing the built-in motion sensor's X-tilt and Y-tilt axes.
Figure 4.5: Built-in Motion Sensor. Depicts the X-tilt and Y-tilt axes for motion-activated controls.
Diagram showing the versatility of the single USB Type-C port for data, simulator, and charging.
Figure 4.6: Single USB Type-C Port. Used for data transmission, simulator connection, and charging.
Diagram illustrating the powerful and efficient cooling system with airflow.
Figure 4.7: Efficient Cooling System. Shows low-noise, high-output fans and an aluminum heat sink to keep the radio cool.

5. Setup

5.1 Battery Installation and Charging

The TX16S MK3 has a built-in USB-C smart balance charging function designed specifically for 3.7V lithium batteries. The charging circuit is designed to charge 2x 3.7V Li-ion 18650 or 2x 3.7V Li-Poly batteries (2s 7.4V Lipo battery pack). The nominal battery voltage is 3.7V, and the charged voltage is 4.2V/Cell.

Approved Battery Types:

  • 2x 3.7V Li-ION 18650 (7.4V using supplied tray)
  • 2x 3.7V Li-ION 21700 (Assembled as 7.4V 2s Battery pack)
  • 2x 3.7V Lithium-polymere (Assembled as 7.4V 2s Battery pack)

DO NOT USE:

  • 2s 6.6V LiFE battery pack
  • 18650 lithium-ion cells with a nominal voltage of 3.6V or LiFEP04 18650 Round cells.

Using the built-in USB charger with incorrect battery types and voltage may cause damage to the remote control or fire.

If using Li-ion cells, ensure they are not protected and are button-top cells. Regularly check the health and condition of your batteries. DO NOT use damaged cells. Never charge your device unattended. Always charge in a safe area away from flammable materials. If the remote control gets wet or damaged in any way, DO NOT charge it.

Illustration of smart active balance charging for 18650 batteries.
Figure 5.1: Smart Active Balance Charging. Prevents overcharging and extends battery life for 18650 Lithium-Ion cells.

6. Operating Instructions

6.1 Binding to a Receiver (ExpressLRS)

  1. TURN OFF the transmitter.
  2. Cycle power to the receiver 3 times. The receiver LED will flash twice, indicating bind mode.
  3. TURN ON the transmitter. Long press the SYS button and choose ExpressLRS LUA under the TOOLS menu. Scroll to [Bind] and press enter.
  4. The LED on the receiver should now be solid, indicating a successful bind.

The TX16S MK3 ELRS units are equipped with an internal ELRS module, transmitting power at a default of 100mW. For non-extreme circumstances, 100mW output at 500Hz update rate is recommended, as higher RF output and update rates may significantly reduce battery life and generate excessive heat.

6.2 Touchscreen Operation

The 5-inch IPS touchscreen (800 x 480 resolution) provides a clear interface for navigation and programming. Use the touchscreen for easy setup and to view telemetry data and widgets.

User interacting with the 5-inch high-visibility color touchscreen.
Figure 6.1: 5-inch High-Visibility Color Touchscreen. Provides ample screen space for widgets, telemetry, and easy setup.

7. Firmware Update

IMPORTANT: The TX16S MK3 is pre-installed with the most stable firmware at the factory. Only attempt to update the firmware if you are confident in the process. Incorrect firmware updates may cause the remote control to become inoperable.

7.1 Updating EdgeTX (UF2) Firmware

Ensure batteries are installed, as USB power alone is insufficient for firmware flashing.

  1. Go to buddy.edgetx.org and download the TX16MK3 UF2 firmware.
  2. Enter Bootloader Mode: Hold T1 and T4 trims inward, then press the Power button.
  3. Connect USB: Two drives will appear (one named UF2).
  4. Copy the downloaded UF2 file to the UF2 drive. The screen will show progress.
  5. When complete, EJECT the drive, DISCONNECT the USB cable, and then REBOOT.

Your EdgeTX firmware is now updated.

7.2 Updating Built-in ELRS Module

  1. Go to expresslrs.github.io/web-flasher.
  2. Select Hardware: RadioMaster TX16S MK3.
  3. Set Flash Method: EdgeTX Passthrough.
  4. Connect the USB to the top port, and choose USB VCP mode.
  5. Install the STM32 VCP driver if connecting for the first time.
  6. Check Full Chip Erase, then CLICK Flash Firmware.

The ELRS module is now updated.

8. Maintenance

  • Battery Care: Regularly check the health and condition of your batteries. Do not use damaged cells. Always charge in a safe area away from flammable materials.
  • Cleaning: Keep the transmitter clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Storage: Store the transmitter in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Gimbal Adjustments: The V6 Hall Gimbals allow for external adjustments of travel, centering, and tension. Refer to the control layout diagram (Figure 4.1) for adjustment points.
  • Shoulder Switch Panels: The modular design allows for replacement of shoulder switch panels to customize your setup.

9. Troubleshooting

  • Transmitter not powering on: Check battery charge level and ensure batteries are correctly installed. Verify battery type is approved.
  • Binding issues: Ensure the receiver is in bind mode (LED flashing twice) and follow the binding instructions carefully. Check that the transmitter's internal RF module is enabled and set to the correct protocol (ExpressLRS).
  • Interference: Avoid operating in areas with high 2.4GHz and Sub-G interference. Ensure antennas are properly positioned.
  • Firmware update failure: Double-check all steps in the firmware update section. Ensure batteries are installed and fully charged before attempting an update. Verify the correct UF2 file is used.
  • Screen unresponsive: Try restarting the transmitter. If the issue persists, a firmware re-flash might be necessary.

10. Specifications

Feature Detail
ItemTX16S MK3 Radio Controller
Size200*178*88mm
Weight813g (without battery)
ColorBlack / Transparent Charcoal
MaterialPlastic
FrequencyISM 2.4GHz and Sub-G 900MHz
Internal RF OptionsELRS 2.4GHz/Sub-G (ExpressLRS 2 x LR1121)
Number of ChannelsUp to 16ch
GimbalsV6 Hall sensor gimbals (AG02 compatible)
Gimbal SticksM4
Display5-inch IPS touchscreen (800 X 480 resolution)
Radio FirmwareEdgeTX (requires 3.0.0 or higher)
Voltage Range6.6 - 8.4V DC
Working Current1.10A (at max RF output power)
Control DistanceMax 2Km
BatteryTwo 3.7V 18650 Lithium-Ion cells / 21700 Li-ion 5000mAh Battery / 2S 7.4V 6200mAh Lipo (batteries not included)
MicroSD Card SlotYes (card not included)
Internal StorageIntegrated 512MB of onboard flash memory
External Module BayJR-compatible module bay
Upgrade MethodUSB / EdgeTX Companion PC software
Recommended Age14+ years
OriginMainland China

11. User Tips

  • For optimal battery life and signal quality, consider using the recommended 100mW output at 500Hz update rate for the internal ELRS module in non-extreme conditions.
  • Regularly check the official RadioMaster website and EdgeTX/ExpressLRS communities for the latest firmware updates and guides.
  • Utilize the modular shoulder switch panels to customize your control layout for your specific flying style or model.
  • Take advantage of the external gimbal adjustments to fine-tune the stick feel to your personal preference.

12. Warranty & Support

If you encounter any problems with your remote control hardware, please retain your proof of purchase and contact the retailer where you purchased the TX16S MK3.

For additional support and resources, you may visit the official RadioMaster website: www.radiomasterrc.com/pages/contact.

A detailed user manual in PDF format is also available for download: View User Manual (PDF).

RadioMaster does not assume any responsibility for any adverse consequences caused by the use or misuse of this product.

13. Compliance Information

13.1 Disclaimer

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

13.2 EU Simple Declaration of Conformity

RadioMaster declares the radio equipment TX16S MK3 is in compliance with EU directives Directive 2014/53/EU.

Manufacturer: ShenZhen RadioMaster Co., Ltd, 3th Floor, Yangtian Building, No. 18 Yangtian Road, Xin'an Street, Baoan District, Shenzhen, Guangdong.

Full text of the declaration of conformity is available at: www.radiomasterrc.com.

13.3 FCC Information

FCC ID: 2BUHG-TX16SM3

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

14. Frequently Asked Questions (FAQ)

No specific FAQs were provided for this product. Please refer to the troubleshooting section or contact support for assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.