Seauto SAT 40

Contents

Seauto SAT 40 Robotic Pool Vacuum User Manual

Model: SAT 40

Brand: Seauto

Seauto SAT 40 Robotic Pool Vacuum

The Seauto SAT 40 Robotic Pool Vacuum is designed for efficient and autonomous pool cleaning, featuring AI sonar navigation and multiple cleaning modes.

1. Product Introduction

Warnings and Precautions

PLEASE READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE USE.

Please adhere to the following warnings and cautions before you use the Pool Cleaner. Use the device only according to these safety instructions. The manufacturer is not liable for any loss or injury caused by improper use of the device.

  • Use only the original battery and battery charger provided.
  • Keep the device out of the reach of children, vulnerable persons (with reduced physical, sensory, or mental abilities), and persons who lack the requisite knowledge and experience. Users must receive appropriate instruction and supervision before using the device. Do not allow children to perform cleaning or maintenance tasks.
  • Be careful when handling the battery casing to avoid the risk of fire and/or burns. Do not open it or crush it and do not place it near a source of heat.
  • Do not insert hands and/or fingers into the impeller motor area.
  • Remove the pool cleaner from the pool before allowing people to enter the pool.
  • Always switch OFF the device before cleaning the filters and/or examining the robot.
  • Be careful when lifting the device to avoid bodily injury.
  • Do not use the device and/or its battery in case of any mechanical damage.
  • Do not use an extension cord to connect the battery charger to electric socket. Use only an appropriately located power outlet.
  • In case of power cord is damaged the entire charger must be replaced with original.
  • Place the battery charger at least 3.5 m / 12 ft from the pool edge during operation.
  • Place the battery charger at least 11 cm / 4 in above the ground to protect users against electric shock.
  • Use a Residual Current Device (RCD) with a rated residual operating current not exceeding 30mA to power up the battery charger.
  • The Lithium-Ion battery should be recycled at a certified battery electronics recycler. Batteries should NOT be discarded as waste or placed in municipal recycling bins. Do not disassemble the battery.
  • Read the instructions carefully before use.
  • Only for use in swimming pool water.
  • Do not use out of water.
  • Do not use when people or animals are in the pool.
  • Do not let children play with the device.
  • Keep out of reach of children.
  • Unplug the device from the power supply before any cleaning or maintenance operation.
  • Only use the provided charger.
  • Do not charge the product immediately after use and ensure that the charging port is completely dry.
  • Do not expose the battery to a heat source or fire.
  • Do not immerse or expose the charger to rain.
  • When using the product, always make sure to insert the battery correctly to ensure its water tightness.

PLEASE SAVE THESE INSTRUCTIONS.

2. Setup

Packaging List

The Seauto SAT 40 Robotic Pool Vacuum package includes the following items:

  • Robot x 1
  • Filter Basket x 1
  • Cartridge x 1
  • Foam x 1
  • Hook x 1
  • Charger x 1
  • User Manual x 1
Seauto SAT 40 Packaging List

Image showing the contents of the Seauto SAT 40 package, including the robot, filter basket, cartridge, foam, hook, charger, and user manual.

Charging the Robot

Before first use, or if the battery is low, charge the robot fully.

  1. Connect the charger to the robot and a power source. The LED indicator will show a solid red light, indicating charging is in progress.
  2. When fully charged, the LED indicator will turn solid green. The device will automatically shut down after 10 minutes to protect the battery.
Robot charging with red LED

Robot connected to charger, showing solid red LED during charging.

Robot fully charged with green LED

Robot fully charged, showing solid green LED. It will power off after 10 minutes.

Placing in Pool

To ensure optimal performance, especially for wall and waterline cleaning, follow these steps:

  1. Before turning on the device, remove the Cartridge to ensure the machine has sufficient power to climb walls and achieve optimal waterline cleaning performance.
  2. Reassemble the filter basket into the device.
  3. Press the power button to turn on the robot. It will display a flashing blue light and announce: "Hello, I'm ready to work, Now it's All-cover Mode."
  4. Place the device into the pool, ensuring the water level is above the top of the machine for normal operation. Once it begins cleaning, the LED will change to a solid blue light.
Removing cartridge before placing in pool

Diagram showing the removal of the cartridge before initial use for optimal wall climbing.

Pressing the power button on the robot

Press the button to power on the robot. A flashing blue light indicates it's ready.

Placing the robot into the pool

Gently place the robot into the pool, ensuring it is fully submerged for operation.

Device Connection (SEAUTO IOT Mobile Application)

The Seauto SAT 40 can be controlled and monitored via the SEAUTO IOT Mobile Application. Download the app from Google Play (for Android) or the App Store (for iOS).

Before connecting, ensure the following:

  • The "Location" function on your phone is turned on, and the app is allowed to access the location.
  • Bluetooth on your phone is enabled.
  • Keep your phone close to the machine (within 16.4 feet / 5 meters) for a stable connection.
App requesting location permission

Screenshot of the app requesting location access on a mobile device.

App requesting Bluetooth permission

Screenshot of the app requesting Bluetooth access to connect to the robot.

App displaying available devices for connection

Screenshot showing the app discovering nearby Seauto devices for connection.

3. Operation

Cleaning Modes

The Seauto SAT 40 offers four cleaning modes, which can be selected via the app or by pressing the device button:

Mode Coverage Area Voice Reminder Runtime
All-cover Mode Covers all areas (floor, walls, waterline) All-cover Mode 2.5-3 hours
Wall Mode Cleans walls only Wall Only 2.5-3 hours
Floor Mode Cleans floor only Floor Only 3-3.5 hours
Waterline Mode Cleans waterline only Waterline Only 2-2.5 hours

Note: The default mode upon startup is All-cover Mode. For Floor-Only Mode, you can insert the foam into the debris bin for enhanced cleaning of fine particles (smaller than 180 microns). Do not use foam in All-cover, Waterline, or Wall modes as it may reduce wall climbing power.

Mode selection button on robot

Press the mode-switch button to cycle through cleaning modes.

Diagram of cleaning modes

Diagram illustrating the four available cleaning modes: All-cover, Wall, Floor, and Waterline.

Video demonstrating the Seauto SAT 40 Robotic Pool Vacuum in action, showcasing its various cleaning modes and features.

Removing from Pool

To remove the robot from the pool:

  1. Before cleaning the filter basket, press and hold the button to turn off the pool cleaner.
  2. Attach the provided hook (included in your package) to a compatible pole (pole not included).
  3. Use the pole to hook and lift the machine out of the pool.
Retrieving robot from pool with hook

Image showing how to use the hook and a pole to safely retrieve the Seauto SAT 40 from the pool.

4. Maintenance

Cleaning the Filter Basket

Clean the filter basket after each use, before it dries out. Ensure the machine is turned off.

  1. Press the switch to ensure the machine is turned off.
  2. Open the cover and remove the filter screen.
  3. Open the lid of the filter basket.
  4. Clean the filter basket thoroughly, then reassemble and place it back into the device.
Opening robot cover to access filter

Step 1: Opening the robot's top cover to access the filter basket.

Removing filter screen

Step 2: Removing the filter screen from the robot.

Opening filter basket lid

Step 3: Opening the lid of the filter basket for cleaning.

Reassembling filter basket

Step 4: Reassembling the cleaned filter basket and placing it back into the robot.

Cleaning the Debris Bin

If you use foam for enhanced cleaning in Floor-Only Mode, clean the foam before it dries. Keep the foam away from direct sunlight.

  1. Remove the debris bin from the filter basket.
  2. Release the buckle and remove the fastener from the debris bin.
  3. Remove and clean the foam.
  4. Reassemble the foam and the fastener into the debris bin.
Removing debris bin from filter basket

Step 1: Removing the debris bin from the filter basket.

Releasing buckle and removing fastener

Step 2: Releasing the buckle and removing the fastener from the debris bin.

Cleaning the foam filter

Step 3: Removing and cleaning the foam filter from the debris bin.

Reassembling foam and fastener

Step 4: Reassembling the cleaned foam and fastener into the debris bin.

Replacing the Battery

To maintain optimal cleaning performance, replace the battery as needed. If a new battery's performance is affected, let the machine sit for 2 days before replacement to ensure complete evaporation of moisture.

  1. Remove the six screws securing the device and take out the old battery.
  2. Insert the new battery following the corresponding position of the old battery.
  3. Install, secure, and tighten the screws.

Note: Before placing the new battery, clean away any foreign objects such as water droplets, sand, etc., from the contact points.

Removing screws for battery replacement

Step 1: Unscrewing the cover to access the battery compartment.

Inserting new battery

Step 2: Carefully inserting the new battery into its designated position.

Off-Season Storage

If the pool cleaner will not be used for an extended period, follow these storage steps:

  1. Ensure there is no water inside the pool cleaner.
  2. Thoroughly clean the filter basket and debris bin, then reassemble them back in place.
  3. Store the pool cleaning robot in a protected location with a temperature between 5°C-45°C / 41°F-113°F. Avoid direct sunlight, rain, or frost.
  4. Charge the pool cleaner once a month to protect the battery.

5. Troubleshooting

If the suggested solutions do not resolve the issue, please feel free to contact us.

Q: Why does the pool cleaning robot not respond after being turned on?
A: The battery may be depleted after prolonged transportation or storage. Please charge the device. The indicator light will remain solid red during charging.
Q: Why can't it climb the wall?
A1: It may be set to Floor-Only Mode. Connect it to the app and select the correct mode.
A2: The debris bin may be inside the filter basket. Remove it to ensure sufficient power for wall climbing.
A3: There may be debris or obstructions inside the filter basket. Remove and clean the filter basket.
Q: Why does the pool cleaning robot fall when cleaning the waterline instead of moving down along the wall?
A: In an infinity pool or a pool with raised edges near the waterline, the robot may fall more easily as it cannot perfectly adhere to the wall.
Q: Why does the cleaner remain stationary or move slowly at the bottom of the pool?
A1: It may be stuck on a floor drain. It will attempt to float autonomously to free itself. If still stuck after a few minutes, assist it using the pole.
A2: If placed in a dirty pool, it may quickly collect a large amount of debris. Check and clean the filter basket if necessary.
Q: Why does the front float while the rear remains on the floor?
A: This is an intelligent function of our pool cleaner designed to help it escape from being stuck.
Q: Why can't my phone connect to the robot?
A: Follow these steps to connect to the pool cleaning robot: a) Keep the machine powered on. b) Check and/or enable Bluetooth on your phone. c) Ensure your phone is close enough to the pool cleaning robot (within 16.4 ft / 5 m).
Q: Why doesn't the cleaner clean the walls or waterline All-cover Mode?
A1: The filter basket may have collected too much debris, reducing its mobility.
A2: The debris bin may be inside the basket. Remove it to ensure sufficient power for wall climbing.
Q: How many smartphones can be connected to one pool cleaning robot?
A: The pool cleaning robot can only be connected to one smartphone at a time. It cannot be connected to other smartphones. If you wish to connect a different smartphone, reset the pool cleaning robot or remove it from the app.
Q: Why are there water droplets inside a newly purchased machine?
A: Each machine undergoes rigorous pre-shipment testing, including underwater tests, which may leave a small amount of water inside. This is normal and safe for use.
Q: Why does the pool cleaning robot automatically shut off after charging for several hours?
A: It is designed to shut down automatically 10 minutes after a full charge to protect the battery and ensure its lifespan. You can leave it charging without safety concerns.

6. Specifications

Feature Specification
Supported Water Depth 1.6-9.8 ft (0.5-3 m)
Charger Input 100-240 VAC, 50-60 Hz
Lithium Battery Capacity 10400 mAh
Battery Runtime (Default Mode) 2-3 hours
Charging Time 5-5.5 hours
Filtration System 294µm Filter Basket + Ultra-fine Foam
Movement Speed 40-80 ft/min (12-24 m/min)
Smartphone Application Android / iOS
Connection Protocol Bluetooth®
Dimensions (L x W x H) 17.32 x 14.88 x 8.82 in / 44 x 37.8 x 22.4 cm
Net Weight 19.8 lbs / 9 kg
Waterproof Rating IP68
Storage Temperature 32 to 104°F (0 to 40°C)
Applicable Pool Size (Max) Up to 3200 sq ft (300 m²)
PH Value Supported 7.0-7.8
Debris Type Leaves; Algae; Stones; Pollen; Soil, etc.
Removable Battery Yes
Suction Motor Quantity 4
Power of Motor 320W
Flow Rate 120 GPM

7. User Tips

  • The Seauto SAT 40 is ideal for in-ground and above-ground pools with flat bottoms, up to 3200 sq ft.
  • For quick operation, simply click the Start button, select your desired cleaning mode, and place the robot in the water.
  • To ensure optimal wall climbing and waterline cleaning, always remove the cartridge before turning on the device and reassemble the filter basket correctly.
  • Regularly clean the filter basket and debris bin, ideally every three to four days, alternating between floor and wall cleaning cycles, to prevent debris accumulation and maintain mobility.
  • If connecting to a new smartphone, remember that the robot can only be connected to one device at a time. You will need to reset the robot or remove it from the previous app connection.
  • It is recommended to film the unboxing process. This can be helpful if any minor cosmetic damage is observed upon arrival, even if the packaging appears intact.

8. Warranty and Support

Warranty Information

This product has passed all quality control and safety tests conducted by the technical department of the factory.

  • 1-year warranty on the machine and 1-year on the battery from the date of purchase.
  • There is no extension warranty for consumables (filter net).
  • This warranty will be void if the product has been altered, misused, or repaired by unauthorized personnel.
  • The warranty extends only to manufacturing defects. It does not cover any damage resulting from mishandling of the product by the owner.
  • The order number or record must be presented for any claim or repair during the warranty period.

Warranty Exclusion Terms - Pool Cleaner Robot

In accordance with French consumer and civil law, legal warranties apply in case of non-compliance or hidden defects. Additionally, any offered commercial warranty shall not cover the following situations:

  • Improper or Inappropriate Use: Use in public, commercial, or collective swimming pools; use in saltwater pools or pools treated with inappropriate or overdosed chemicals; use with water that has unsuitable pH, temperature, or chlorine levels, outside the manufacturer's recommended ranges; use of the robot out of the water, or in an empty or partially filled pool.
  • Improper Maintenance and Storage: Lack of regular maintenance (e.g., filter cleaning, rinsing after use); storage in improper environments such as freezing temperatures, excessive humidity, extreme heat, or prolonged sun exposure; damage caused by foreign objects left in the pool (e.g., toys, rocks, debris).
  • Physical or Cosmetic Damage: Damage due to impacts, drops, or mishandling; scratches, cracks, or other aesthetic issues that do not affect the functionality; water infiltration caused by misaligned or non-original seals.
  • Unauthorized Repairs or Modifications: Repairs or tampering performed by unauthorized or unqualified personnel; disassembly or opening of the device without authorization; use of non-original or non-certified spare parts.
  • Electrical or Environmental Issues: Use with an unsuitable electrical supply (voltage, frequency, or unprotected outlets); damage caused by power surges, lightning, short circuits, or faulty installation; immersion of non-waterproof components (e.g., transformer, control unit) in water.
  • Normal Wear and Tear: Wear of consumable parts such as brushes, filters, belts, wheels, etc.; gradual performance loss due to intensive use or the product's normal lifespan.
  • Failure to Follow User Manual: Failure to follow usage, safety, or installation instructions provided in the user manual; failure to register the product when required for warranty activation.
  • Force Majeure or Accidental Events: Damage resulting from fire, flooding, earthquakes, vandalism, theft, or any other unforeseeable external events.

Notice: Any warranty claim must be accompanied by proof of purchase, full compliance with the user manual, and may be subject to technical inspection.

Declaration of Conformity (CE)

Seauto declares that this product meets all the requirements of the applicable European directives 2014/35/EU (LVD); 2014/30/EU(EMC); 2011/65/EU (RoHS). N°1907/2006 (REACH). You can request the full text of the declaration of conformity by emailing to support@seautorobots.com.

Contact Information

  • Built by: Seauto
  • Manufacture Model: SAT 40
  • Phone: +1 800-618-8968
  • Email: support@seautorobots.com
  • Operating Hours: Mon-Fri, 09:00-18:00 (EST)
  • Made in: China

A detailed user manual (PDF) is available for download here.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.