COOSPO S10

Contents

COOSPO S10 Spider Bike Power Meter User Manual

High-Precision Power Meter for Road Bicycles

1. Product Introduction

The COOSPO S10 spider power meter is specially designed for road bike training, featuring automatic calibration and temperature compensation to ensure accurate and reliable power measurement. It supports dual ANT+/Bluetooth wireless transmission, compatible with major bike computers and training apps, helping cyclists scientifically evaluate performance and improve training efficiency.

Thank you for purchasing. Please read this user manual carefully before use and keep it for future reference.

COOSPO S10 Spider Power Meter front view

COOSPO S10 Spider Power Meter

2. In the Box

The package includes the following items:

  • 1 x COOSPO S10 Spider Power Meter
  • 1 x Magnetic Charging Cable
  • 1 x User Manual (this document)
  • 1 x DIY Sticker

Video: Unboxing and initial contents of the COOSPO S10 Spider Power Meter.

3. First Use & Charging

The power meter is in shipping mode by default. Before the first use, please charge it to exit this mode:

  1. Use the original magnetic charging cable for charging.
  2. When connected to power, the LED indicator will turn on, meaning the power meter is activated. If the LED does not light up, please check the cable connection or try another power adapter.
  3. It is recommended to fully charge the power meter before first use.

Note: The power meter cannot be activated or paired until it exits shipping mode through charging.

LED Indicator Status

OperationLED Indicator
Wake UpGreen LED flashes for 30s if battery is sufficient; Red LED flashes for 30s if battery is below 15%.
Bluetooth ConnectionBlue LED flashes quickly when a connection request is detected. After successful connection, blue LED stays on for 15s. If it turns off within 15s, the connection failed or was disconnected.
ChargingRed LED stays on during charging; green LED stays on when fully charged.
Firmware UpgradeBlue LED stays on during upgrade; automatically turns off when upgrade is complete.

Note: During normal riding, the LED indicators will automatically turn off to save power.

4. Installation

This product should be installed by a person with relevant experience or professional knowledge. If you are not familiar with the installation, please contact a professional mechanic or bike shop for assistance.

Tools Needed

  • Torque Wrench: Ensures all bolts are tightened to the correct specification, critical for accuracy and safety. Used for crank and chainring bolts.
  • Crankset Removal Tool: Specific to your crankset (e.g., Shimano or SRAM).

Installation Precautions

  • The S10 with Easton interface only works with Easton cranks.
  • Chainrings must be 110 BCD; the brand does not matter.
  • Make sure the Easton crankset you purchased is compatible with your bike frame (Bottom Bracket).
  • During installation, ensure the power meter does not interfere or collide with the crank, frame, chain, or cassette.
  • After installation, we recommend 1-2 test rides. If you notice any looseness, unusual noise, or abnormal readings, stop using the power meter immediately and check the installation.

Installation Steps

  1. Remove the crankset from your bike.
  2. Use the crankset removal tool according to your system.
  3. Remove the crank from your crankset.
  4. Prepare an Easton crankset.
  5. Install the power meter with the Easton crankset.
  6. Use the torque wrench to fix the power meter to your crank. It is recommended to use a torque wrench and apply the specific torque.
  7. Install the chainrings. Make sure the chainring is installed in the right direction.
  8. Please use the recommended torque tightening screws. Read the manufacturer's manual for torque specifications and check the specific torque on the bike part.
  9. Tighten chainring bolts in a cross pattern. Follow manufacturer torque values (do not guess).
  10. Power meter installation completed.
  11. Install the crankset with power meter to your bike.
Seamless Compatibility with Easton 110 BCD 4-bolt

Image: Seamless Compatibility with Easton 110 BCD 4-bolt cranksets.

5. Operating the Power Meter

Wake-up

The power meter has a motion-sensing automatic wake-up function and does not require manual operation. Simply rotate the crank or pedal 1-2 turns, and the device will wake up automatically. The LED will flash continuously to indicate the current battery level (refer to the 'LED Indicator' table above).

Sleep Mode

When the power meter detects no movement for more than 5 minutes, it will automatically enter sleep mode. During sleep mode, connection information will be retained, and the device will automatically reconnect when awakened.

Connection

Preparation before connecting:

  • Make sure the power meter is awake.
  • Turn on ANT+ or Bluetooth on your device and keep it within 3 meters of the power meter.
  • If connected to another power meter, disconnect it first to avoid interference.

Connect to Bike Computer (Using COOSPO CS600 as an Example):

  1. Turn on the CS600 bike computer, go to the Settings page, and select Sensors to enter the device management page.
  2. Choose Add Sensor, then select the S10 power meter from the list and connect via Bluetooth or ANT+ ID (ANT+ is recommended).
  3. After connecting, the power meter's blue LED will flash quickly and then stay on for 15 seconds. If the connection fails or is interrupted, the LED will turn off. (When connected via ANT+, the LED does not change; for details, please refer to the LED Indicator section.)

Connect to Coospo Tools App:

  1. Turn on your phone's Bluetooth and open the Coospo Tools App.
  2. Go to the Sensor Management page and tap Connect Device.
  3. From the list of detected devices, connect to the S10 power meter by its Bluetooth ID.
  4. After connecting, the power meter's blue LED will flash quickly and then stay on for 15 seconds. If the connection fails or is interrupted, the LED will turn off. (For details, please refer to the LED Indicator section.)
Instant Connectivity with ANT+ and Bluetooth, showing connection to bike computers and apps

Image: Instant Connectivity with various cycling devices and apps.

6. Calibration

The S10 spider power meter features automatic calibration. However, manual calibration is recommended in the following situations:

  • After first installation or reinstallation.
  • When there is a significant change in temperature (e.g., moving from indoors to outdoors).
  • Before each formal training session or race.

Manual Calibration Steps:

  1. Open the official app or bike computer and connect to the power meter.
  2. Go to the "Sensor Management" or "Power Meter Setting" page.
  3. Ensure the bike is stationary, with no external force applied to the pedals or crankarm (do not pedal or rotate).
  4. Tap the "Calibrate" button.
  5. Wait until the device displays "Calibration Complete," then you can start riding.

7. Specifications

FeatureSpecification
Power Accuracy±1%
Weight102 g
Battery Life300 h
Battery TypeRechargeable lithium battery
Wireless ProtocolsANT+, Bluetooth
Waterproof RatingIPX7
Operating Temperature-20 °C to 60 °C
Storage Temperature-30 °C to 60 °C
Power Range0-2800 W
Cadence Range20-240 RPM
Measured DataPower, Cadence, Left/Right Balance, Pedal Smoothness
Sensor8-piece Strain Gauge Sensor
Input PowerDC 5V
Charging Duration1.5h
Ultra Stable Measurement with +/- 1% accuracy

Image: Ultra Stable Measurement with ±1% accuracy and max power measurement up to 2800W.

Smarter Training Insights showing Power, Cadence, Left-right Balance, Pedal smoothness

Image: Smarter Training Insights providing data types like Power, Cadence, Left-right Balance, and Pedal Smoothness.

Lightweight, Durable Construction, 102g weight

Image: Lightweight and Durable Construction, weighing only 102g.

8. Cleaning and Maintenance

  • Regularly wipe the surface of the power meter gently with a soft, damp cloth or clean water to remove mud, dust, or sweat.
  • The power meter is rainproof (IPX7) and can be used in rainy weather, but do not immerse it in water or clean it with a high-pressure water jet.
  • Avoid strong impacts to the crankset or power meter, as they may cause damage.
  • Regularly check that the screws fixing the power meter, crankarm, and chainring are tight.
  • It is recommended to perform a zero calibration once a week or before each long ride to ensure accurate power data.

9. Troubleshooting & Attentions

General Attentions

  • Regularly connect to the official App or bike computer to check for firmware updates for the latest features and performance improvements.
  • Do not disassemble or repair any components by force.
  • If the power meter will not be used for a long time, it is recommended to charge it once every 6 months to maintain battery health. After fully charging, store it in a cool, dry place.
  • Do not open or modify the product.
  • Do not disassemble or attempt to service this product.
  • This product is safe under normal and reasonably foreseeable operating conditions.

Battery Safety Warning

Warning:

Please follow the instructions in the user manual when using this product. Do not disassemble, modify, crush, or damage the battery. Do not charge the battery near fire or in extreme temperatures. It is recommended to charge the battery within a temperature range of -10°C to +45°C to ensure safety and optimal performance. Keep this product out of reach of children to avoid misuse or accidents. If the battery gets wet or submerged, stop using it immediately and handle it properly.

10. User Tips

  • Regularly check for firmware updates to ensure optimal performance and accuracy.
  • Perform zero calibration frequently, especially before important rides or if you notice discrepancies in readings.
  • Ensure proper installation and torque settings to avoid accuracy issues.

11. Frequently Asked Questions (FAQ)

  • Is the S10 compatible with SRAM FORCE AXS? Please refer to the installation section regarding the Easton interface and 110 BCD chainring requirements.
  • Is it compatible with Shimano XT / Tiagra / Ultegra Di2 12v / 105 R7100 cranks? Compatibility depends on the crankset's interface and BCD. The S10 is designed for Easton interface and 110 BCD chainrings. Please check your specific crankset's specifications.
  • Is it compatible with SRAM Force / XX SL cranksets? Compatibility depends on the crankset's interface and BCD. The S10 is designed for Easton interface and 110 BCD chainrings. Please check your specific crankset's specifications.
  • Is it compatible with Shimano GRX400? Compatibility depends on the crankset's interface and BCD. The S10 is designed for Easton interface and 110 BCD chainrings. Please check your specific crankset's specifications.
  • Can I buy just the crank arm/crank? The COOSPO S10 is a spider power meter designed to integrate with compatible cranksets. It is not sold as a complete crankset.

12. Warranty & Support

If the product is operating improperly, please contact COOSPO support. The product must be returned to the manufacturer for any service or repair.

Manufacturer: Shenzhen Coospo Tech Co., Ltd
Address: 6F, Building A, Dingxin Science Park, Xinan Street, Baoan District, Shenzhen
Contact: +86 (755) 23594795
Email: support@coospo.com
Website: www.coospo.com

For additional item guides and documents, you may refer to the official PDF manual: COOSPO S10 User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.