Junsun Wallbox Type 2 EV Charger

Contents

Junsun Wallbox Type 2 EV Charger User Manual

Model: Wallbox Type 2 EV Charger

Brand: Junsun

1. Introduction

This manual provides essential information for the safe and efficient operation of your Junsun Wallbox Type 2 EV Charger. Please read it thoroughly before installation and use to ensure proper functionality and safety.

2. Safety Precautions

2.1. Installation Safety

  • Installation is restricted to properly trained, qualified, and authorized electrical professionals.
  • First commissioning and maintenance must comply with existing standards and installation regulations.
  • Always cut off power supply before connecting external power supply to charger input. Do not connect the line with electricity.
  • No extension cables must be used when connecting an electric vehicle to an electric vehicle power supply.
  • Repair or replacement of the charger shall not be carried out without authorization, and only by the manufacturer. Do not modify the charger without authorization.
  • Do not remove safety signs, warning labels, nameplates, or signage.

2.2. Electrical Hazards/Fire Hazards

  • When using the charger, please read the relevant tips and instructions of the vehicle carefully.
  • It is necessary to regularly check whether there is damage on the socket or charging cable (including the charging cable) of the charger and check if the housing is broken.
  • If the charger is damaged, it must be turned off and replaced immediately.
  • Only connect electric vehicles or their charging equipment; do not connect other loads (e.g., power tools).
  • When pulling the charging gun, please hold the plug, not the cable.
  • Do not bend, squeeze, or tilt the charging gun to avoid mechanical damage. Avoid contact with heat, dirt, or water.
  • Ensure adequate external ventilation system if charging in indoor areas where toxic or explosive gases may be produced.
  • Avoid dropping the charger or strong mechanical impact, otherwise it may destroy the electrical safety of the equipment causing potential safety hazards.
  • It is strictly forbidden to use in an environment with combustible materials or explosive gases, otherwise there is a risk of explosion.
  • Do not let conductive objects such as metal foreign objects fall into the inside of the charger, otherwise accidents may occur.
  • The PE (Protective Earth) end of the charger must be reliably connected.

3. Package Contents

The package typically contains the following items:

  • The charger x1
  • Empty Gun Holder x1
  • Card x2
  • Screw x9
  • Expansion Screws x4
  • Specification x1
  • Certificate Of Conformity x1
  • Packing List x1
Image showing all package contents including the charger, gun holder, cards, screws, specification, certificate, and packing list.

Image: Overview of the Junsun EV charger package contents.

4. Installation

4.1. Mounting the Charger

The charger is designed for hanging installation. Follow these steps:

  1. Fix the back panel to the wall using small screws.
  2. Fix the entire machine to the back panel on the wall using small screws.
Diagram showing two steps for hanging installation: first attaching a back panel to the wall, then mounting the charger onto the back panel.

Image: Step-by-step diagram for wall mounting the EV charger.

4.2. Wiring Steps

Connect the input wire connectors L, N, and PE of the plug to the corresponding hollow open L, N, and PE ends of the distribution box.

Wiring diagram showing the connection of L, N, and PE wires from the charger plug to a distribution box.

Image: Wiring diagram illustrating how to connect the charger to the electrical distribution box.

5. Operation

5.1. Charging Steps

  1. Ensure the charging station is correctly connected to the power supply.
  2. Insert the charging gun into the vehicle's gun slot.
  3. Start charging using card swiping or APP code scanning.
  4. The normal charging of the vehicle is completed.
  5. Click on the app or swipe to end charging.
  6. Unplug the charging gun and return it to its original position.
Six-panel diagram illustrating the steps for operating the EV charger, from connecting to power to unplugging the charging gun.

Image: Visual guide for the EV charger usage steps.

5.2. Indicator Description and Status

The charger features an indicator light and a display screen to show its current status. Below is a summary of the indicator behavior for different operating states:

  • Idle State: Indicator light is always green. The display shows 0.000 kWh, 0.00 kW, 226.8 V, 0.00 A, and 00:00:00. Road light is green constantly on.
  • Connected State: Indicator light flashes green. The display shows 0.000 kWh, 0.00 kW, 226.8 V, 0.00 A, and 00:00:00. Road light is green constantly on.
  • Delay State: Indicator light is always blue. The display shows 56.703 kWh, 7.05 kW, 226.8 V, 31.1 A, and 08:06:12. Road lights transition from blue to yellow, always on.
  • Charging State: Indicator light flashes blue. The display shows 56.703 kWh, 7.05 kW, 226.8 V, 31.1 A, and 08:06:12. Charging light flashes green. Road lights show a blue flow.
  • Charging Finish State: Indicator light is always blue. The display shows 56.703 kWh, 7.05 kW, 226.8 V, 31.1 A, and 08:06:12. Charging light is green always on. Road light is blue constantly on.
  • Fault State: Indicator light flashes red. The display shows E01 (example fault code), 0.000 kWh, 0.00 kW, 226.8 V, 0.00 A, and 08:06:12. Road light is red constantly on.
Diagram illustrating various indicator light states (Idle, Connect, Delay, Charging, Charging Finish, Fault) and corresponding display information on the EV charger.

Image: Detailed view of the charger's display and indicator light behavior for different operating states.

Indicator Light State Table

Operating StateRedGreenBlueCode
Idle (no Wi-Fi connect)/Flash//
Idle/Always on//
Insert charging gun/Flash//
Charging//Flash/
Charging finish//Always on/
Over-voltage protectionFlash 1 time//E01
Under-voltage protectionFlash 2 time//E02
Over current protectionFlash 3 time//E03
PCB main board over-temp protectionFlash 4 time//E04
Ground protectionFlash 5 time//E05
CP voltage protectionFlash 6 time//E06
Relay faultFlash 7 time//E07
Leakage protectionFlash 8 time//E08
E-stop buttonFlash 15 time//E15
Card reader faultFlash 16 time//E16
Ammeter faultFlash 17 time//E17
Swipe stop///S1
APP stop///S2
Fully charged stop///S3
Car stop///S4
Under-balance stop (operational version)///S5
Charge interruption (operational version)///S6

6. Specifications

The Junsun Wallbox EV Charger is available in various configurations. Key specifications include:

FeatureSpecification
TouchscreenYes
Operating Temperature-30℃~+50℃
Wireless SupportNo
Cable Length4m/5m (optional)
IP Rating (Charger)IP65
Voltage195V~220V
Current6-8-10-13-16-20-24-32A (Optional)
MaterialTPU
Charger TypeType 2
Power (W)1.3~7KW (Optional)
Weight2.8~4kg
Leakage protectionAC30mA/AC30mA+DC 6mA (Optional)
PlugSchuko/CEE (Optional)
CEE power plug IP RatingIP44
Control box Protection DegreeIP65
Plug Protection DegreeIP55
Frequency50/60HZ
Rated Power3.5kw&7kw (Optional)
Phase1 Phase
Charging TypeType2 IEC 62752

Physical Dimensions

Control box dimensions: 18.6cm (width) x 35.4cm (height) x 11.1cm (depth).

Cable length from control box to gun head: 3.5m / 4.5m / 7.5m / 9.5m (Custom made options available).

Diagram showing the dimensions of the EV charger control box and cable length options.

Image: Dimensions of the charger and cable length options.

Image showing compatibility with various EV models including Audi, BMW, Chevrolet, Chrysler, Fiat, Ford, Honda, Jaguar, Kia, Nissan, Porsche, Toyota. Notes suitability for Tesla with an IEC 62752 adapter.

Image: Compatibility chart for various electric vehicle models.

7. Maintenance

Regularly inspect the charging cable and plug for any signs of wear, damage, or corrosion. Ensure the control box and charging gun are clean and free from dirt, dust, and moisture. Do not attempt to open or repair the unit yourself; contact qualified service personnel for any issues.

The charger is designed to withstand various environmental conditions:

  • Rainy environment: IP65 rated for protection against water jets.
  • Heavy snow environment: Withstands temperatures down to -30°C.
  • Sunscreen prevention: Withstands temperatures up to +50°C.
Image demonstrating the charger's durability in rainy, snowy, and sunny environments, highlighting IP65 rating and temperature resistance.

Image: Environmental resistance features of the charger.

8. Troubleshooting

If you encounter any issues with your Junsun EV Charger, refer to the table below for possible causes and suggested solutions.

Fault NamePossible CauseExclusion Suggestions
AC overvoltageAC input voltage too high
  1. If voltage exceeds 265Vac for a short time, wait for power grid to recover to within the normal voltage range.
  2. Check background monitoring data. If long-term overvoltage, adjust input overvoltage protection point up to 265Vac via configuration software.
AC undervoltageAC input voltage too lowCheck background monitoring data. If long-term undervoltage (175Vac), adjust input undervoltage protection point down to 90 Vac via configuration software.
AC overcurrentExcessive AC input current
  1. Immediately disconnect leakage/overcurrent protection circuit breaker of distribution box.
  2. Check for low impedance or short circuit between output lines of AC pile.
  3. After troubleshooting, power on again. If fault persists, please contact us.
Over TempThe temp inside the AC pile is too highCheck installation environment for other heating devices. Ensure ambient temperature is below 50°C.
Excessive leakage currentExcessive ground leakage current
  1. Immediately disconnect leakage/overcurrent protection switch of distribution box.
  2. Check if output line of AC pile is damaged or has low impedance/short circuit to ground.
  3. After troubleshooting, power on again. If fault persists, please contact us.
Ground FaultPoor grounding of input/output or reverse connection of input L/N
  1. Immediately disconnect leakage/overcurrent protection switch of distribution box.
  2. Check whether grounding of input/output lines of AC pile is normal, and whether input L/N is connected in normal order.
  3. After troubleshooting, power on again. If fault persists, please contact us.
Abnormal communication (internet mode)Poor communication in the background of the communication pile
  1. Check if network cable connection is correct and reliable.
  2. Check whether charging station configuration is correct in the background.
Abnormal connection of charging gunAbnormal connection of charging gun CC/CP
  1. Check if connection of charging gun is correct and reliable.
  2. If fault persists, please contact us.

9. User Tips

Based on common user inquiries and experiences, consider the following tips:

  • Power Reduction: If you purchase an 11KW or 22KW charger but your car does not support 3-Phase power, the device will automatically reduce the power to support a maximum of 3.5KW or 7KW to protect your vehicle.
  • Last Current Value: The charger remembers the last charging current value used.
  • Scheduling: While direct timer setting is not available, you can schedule charging for up to 5 hours.
  • Grounding: The charger supports grounding.
  • Compatibility: This product is suitable for all Type 2 interface EV models. For Tesla vehicles, an IEC 62752 adapter may be needed.
  • Plug Diameter: A 3.5KW charger can use a standard household socket. For 7KW (blue connector), the diameter is 55mm. For 11KW (red connector), it's 55mm. For 22KW (red connector), it's 63mm.
  • Leakage Protection: 3.5KW and 7KW models have AC 30mA protection. 11KW and 22KW models have AC 30mA + 6mA DC leakage protection.

10. Warranty and Support

The product comes with a 2-year quality guarantee and replacement/repair within 365 days. For detailed warranty information or technical support, please refer to the official product documentation or contact Junsun customer service. A PDF user manual is available for download for more comprehensive information.

For a comprehensive guide, please refer to the User Manual (PDF).

Image displaying various certifications such as UKCA, TUV, and CE certificates, indicating quality assurance.

Image: Product certifications for quality assurance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.