LEXON R1/R1S

Contents

LEXON R1/R1S Superlight Full Carbon Crankset User Manual

Model: R1/R1S

Critical Safety Warnings

Failure to follow these warnings may result in serious injury or damage to components.

  1. A Torque Wrench is Mandatory: You MUST use a calibrated torque wrench for all bolts. Overtightening can damage carbon fiber or aluminum threads, leading to catastrophic failure.
  2. Verify Compatibility:
    • Road Models: Ensure your frame's bottom bracket standard (e.g., BB86, BB30, PF30) is fully compatible with the crankset's spindle diameter (24mm or 29mm) and the corresponding bottom bracket.
    • Mountain Models: Ensure your frame's bottom bracket standard (e.g., BB92, PF30) is fully compatible with the 29mm spindle and its specific bottom bracket.
    • Use Carbon Assembly Paste: Always apply a thin layer of carbon fiber assembly paste to all carbon-on-carbon contact surfaces (e.g., spindle interface, preload cap) to prevent slippage and creaking.
    • Do Not Use Damaged Parts: Inspect the crank arms, chainrings, and all bolts for any cracks or damage before installation. Do not install if compromised.

Setup and Installation

Professional installation by a qualified bicycle mechanic is strongly recommended for safety and optimal performance.

Key Installation Steps

  1. Install Bottom Bracket: Press-fit or thread the correct bottom bracket cups into your frame according to its standard.
  2. Install Crankset:
    • Insert the drive-side crank arm/spindle through the bottom bracket.
    • Attach the non-drive-side arm and hand-tighten the fixing bolt(s).
  3. Set Preload (if applicable): For systems with a preload adjuster, turn until all play is eliminated and the crank spins smoothly.
  4. Final Torque: Using a torque wrench, tighten all fixing bolts to the exact specification printed on the crank arm, following a cross pattern. Do not exceed the specified value.
  5. Install Chainrings: Secure the chainrings to the crank arm using the chainring bolts. Torque to spec (typically 10-14 N-m) in a cross pattern.

Spider and Chainring Compatibility

The RYET AERO SPIDER is designed for 110BCD Direct-Mount Interface and is compatible with EASTON/RACEFACE Direct Mount Interface.

RYET Aero Spider for Direct Mount Interface

Image: RYET Aero Spider for 110BCD Direct-Mount Interface. Note: Fits EASTON/RACEFACE Direct Mount Interface.

Chainring Compatibility Chart

Chainring Compatibility Chart

Image: Compatibility chart showing various chainring and spider combinations. Compatible with EASTON interface disc, EASTON interface Spider, RYET 1X/2X Chainring. Not directly compatible with SHIMAN* Chainring without an adapter.

Operating Instructions

Power Meter Functionality (if equipped with XPOWER-S)

The XPOWER-S power meter utilizes an ANT+/Bluetooth 4.0 Dual-Mode chip for broad compatibility.

ANT+ Bluetooth 4.0 Dual-Mode Connectivity

Image: Devices connected via ANT+/Bluetooth 4.0 Dual-Mode. The XPOWER-S can connect with Garmin, Bryton, Wahoo, and other bike computers. It also connects to smartphones for apps like Strava, Zwift, Onelap, TrainerRoad, and PerfPro.

XCADEY App Usage

For XPOWER-S power meters, download and use the XCADEY App to:

  • Connect to your power meter.
  • View real-time data such as watts and cadence.
  • Check hardware information.
  • Adjust calibration values.
  • Upgrade firmware.
XCADEY App Interface

Image: XCADEY App interface showing data display and settings. The app allows users to monitor power and cadence, and manage device settings.

Care, Inspection & Maintenance

  • Initial Check: After the first 50 km of riding, re-check the torque on all crank and chainring bolts, as settling may occur.
  • Regular Inspection: Periodically (e.g., monthly) check bolt torque and inspect crank arms and chainrings for cracks, unusual flex, or noise.
  • Cleaning: Wipe with a damp cloth. Avoid directing high-pressure water at bearing seals or bolt interfaces. Do not use corrosive cleaners.
  • Lubrication: Use only specified lubricant or anti-seize compound on metal threads. Never use grease on carbon contact surfaces.

Power Meter Battery Replacement (LITE EASTON 110BCD 4S)

If your power meter uses a CR2032 battery:

  • Replace with CR2032 only.
  • The battery is not rechargeable – do not attempt to charge it.
Power Meter Battery Usage

Image: Battery usage instructions for LITE EASTON 110BCD 4S power meter. Indicates to replace with CR2032 only and not to recharge.

Troubleshooting

If you encounter issues, consider the following:

  • Creaking Noises: Re-check all bolt torques, especially crank arm and chainring bolts. Ensure carbon assembly paste was used on all carbon-on-carbon contact surfaces during installation.
  • Power Meter Connectivity Issues: Ensure the power meter battery is fresh. Check your bike computer or smartphone's Bluetooth/ANT+ settings. Try re-pairing the device. Update power meter firmware via the XCADEY App.
  • Shifting Problems: Ensure chainrings are correctly installed and torqued. Verify chainring compatibility with your drivetrain.
  • Unusual Flex or Damage: Immediately stop using the crankset and inspect for cracks or damage. Do not use compromised parts. Consult a professional bicycle mechanic.

Specifications

LEXON R1/R1S Crankset

Crankset Product Parameters

Image: Crankset product parameters including arm length, speeds, material, spindle size, and weight.

  • Crank Arm Length: 162.5mm, 165mm, 167.5mm, 170mm, 172.5mm, 175mm
  • Crankset Speed: 11S/12S
  • Bike Crank Materials: High-Mode Carbon
  • Crank Spindle Size: Width 93mm, Diameter 29mm (Aerospace-Grade Aluminium Spindle)
  • BB Compatibility: All 29mm BBs
  • Spider Interface: Fit for Easton Interface (LEXON 16T)
  • Cranksets Chainline: R1/R1S Spider 44.5MM
  • Bike Crank Q Factor: 151mm
  • Weight:
    • 2025 R1: 365g (165mm Cranksets only, Spider not included)
    • 2026 R1S: 329g (165mm Cranksets only, Spider not included)
  • Design Architecture:
    • 2025 R1: Two-Piece Dual-Side Bolt Fixation
    • 2026 R1S: One-Piece Integrated Spindle Design, Single-Side Bolt Fixation
  • Features: Toray high modulus carbon fiber, dual-channel technology for 12% improved rigidity, cold forged 7075 aluminum alloy axle core, passed 1800N 14w crank fatigue test and 5600N crank damage test.

RYET EVO Alloy Chainrings

Chainring Specifications

Image: Chainring specifications including material, speed, BCD, size, and weight.

  • Material: AL 7075-T6 CNC
  • Speed: 11s / 12s
  • BCD: 110x4 Shimano® Symmetric
  • Chainring Sizes:
    • 2X: 50-34T, 52-36T, 54-40T, 56-42T
    • 1X: 46T, 48T, 50T, 52T
  • Weight (2X): 50-34T (150g±10g), 52-36T (170g±10g), 54-40T (175g±10g)
  • Weight (1X): 46T (125g±5g), 48T (135g±5g), 50T (145g±5g), 52T (165g±5g)
  • Attachment: 4-arm spider
  • Surface Coating: Anodizing
  • Note: Not directly compatible with SHIMANO Cranksets. Use LEXON Chainring Bolt Sets due to thicker chainring.

XCADEY XPOWER-S Power Meter (if equipped)

XCADEY Power Meter Specifications

Image: XCADEY Power Meter specifications including battery life, wireless protocol, app support, accuracy, waterproof rating, and battery type.

  • Battery Life: 150 Hours
  • Wireless: ANT+ / Bluetooth 4.0
  • APP Support: XCADEY APP
  • Accuracy: -/+ 1.5%
  • Waterproof: IP67
  • Battery: Li-ion Battery (Internal, not user-replaceable for main unit; CR2032 for LITE EASTON 110BCD 4S spider)
  • Power Range: 0 - 2500 Watts
  • Cadence Range: 30 - 220 RPM
  • Working Temperature: -10 - 50 °C
  • Limited Warranty: 16 Months
  • Data Support: Power, Cadence, Balance

User Tips

  • Always use a torque wrench for all installations and checks to prevent damage to carbon components.
  • Regularly clean your crankset with a damp cloth to remove dirt and grime, avoiding high-pressure water on bearings.
  • For optimal power meter accuracy, ensure it is calibrated according to the XCADEY App instructions.
  • If upgrading chainrings, ensure they are compatible with the LEXON/RYET spider interface and use appropriate chainring bolts.

Warranty and Support

Warranty Information

Image: Warranty details provided by LEXON.

  • After-Sale Services: Life-time after-sale services are provided.
  • Cranksets Warranty: Two-Years Warranty on cranksets under normal use.
  • Chainring Warranty: One-Year Warranty on chainrings under normal use.
  • Power Meter Warranty: 16 Months Limited Warranty for XPOWER-S power meters.

For any support inquiries, please contact your retailer or LEXON customer service.

© 2024 LEXON. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.