1. Introduction
1.1 Vehicle Coverage
This diagnostic tool is specifically designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN). It is required by EPA that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant, and this includes all American, Asian, and European vehicles.
A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the following:
- Vehicle Emissions Control Information (VECI) Label: It is located under the hood or by the radiator of most vehicles. If the vehicle is OBD II compliant, the label will designate "OBD II Certified".

Image: Vehicle Emission Control Information label indicating OBD II certification.
- Government regulations mandate that all OBD II compliant vehicles have a "common" 16-pin Data Link Connector (DLC).

Image: Standard 16-pin Data Link Connector (DLC) with pin numbering.
Note: Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD II compliant. Only those vehicles with a Vehicle Emissions Control Label stating OBD II Certified are OBD II compliant.
1.2 On-Board Diagnostics (OBD) II
The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions, which will offer three pieces of valuable information:
- Whether the Malfunction Indicator Light (MIL) is commanded “on” or “off”;
- Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
- Readiness Monitor status.
1.3 OBD II Definitions
The following terms and their definitions are related to OBD II systems:
- EOBD: European On-Board Diagnostics. Essentially the same as OBD II, with the same Data Link Connector and Communication Protocols.
- Communication Protocols: Allows different systems and sensors in a vehicle to communicate. Currently, there are five protocols: CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
- Powertrain Control Module (PCM): The OBD II accepted term for the vehicle's "on-board computer." It controls engine management, emissions systems, and powertrain operation.
- DLC (Data Link Connector): The 16-cavity connector on the vehicle that allows communication between the computer system and the diagnostic tool.
- MIL (Malfunction Indicator Light): The vehicle's “Check Engine” warning light that activates when a DTC is stored.
- DTC (Diagnostic Trouble Code): A code stored in the computer system's memory, identifying a fault condition causing the MIL to activate.
- Freeze Frame Data: Operating conditions that are stored when a DTC is stored.
- PID (Parameter Identification Data): Data returned by the vehicle's control modules to the diagnostic tool.
- Monitors: “Diagnostic routines” programmed into the PCM to run diagnostic tests and monitor emissions-related components.
- Enabling Criteria: Vehicle-specific events or conditions that must occur before monitors will run.
- Trip: A period during which all required “Enabling Criteria” for a monitor to run and complete its diagnostic testing are met.
- Drive Cycle: A specific mode of vehicle operation that provides conditions required to set all readiness monitors to the "ready" condition.
- Warm-up Cycle: Vehicle operation after an engine off period where engine temperature rises at least 40°F (22°C) and reaches at least 160°F (70°C).
- Fuel Trim (FT): Feedback adjustments to the base fuel schedule (short-term for dynamic, long-term for gradual changes).
1.4 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are codes stored by the on-board computer diagnostic system. They are five-digit alphanumeric codes. The first character (a letter) identifies the control system, the second (a number 0-3) provides general information, and the last three (hex characters 0-9 or A-F) give specific details about the fault's origin and conditions.

Image: Diagram illustrating the structure of a Diagnostic Trouble Code (DTC) with P0202 as an example, showing system and sub-system identification.
1.5 Location of the Data Link Connector (DLC)
The DLC is typically a 16-pin connector. It is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary. If the DLC cannot be found, refer to the vehicle's service manual for the location.
2. Setup
2.1 Components & Controls
The LAUNCH X431 ELITE V3.0 diagnostic tool features the following components:

Image: Top and front views of the diagnostic tool with numbered components.
| No. | Name | Description |
|---|---|---|
| 1 | Charging port | Charge the tool via data cable (not included). |
| 2 | DB-15 diagnostic connector | Connect the diagnostic cable. |
| 3 | Power button | Turn on/off the tool. |
| 4 | Touch screen | Indicate the test results. |
| 5 | BACK button | Exit the current program or return to the previous screen. |
| 6 | HOME button | Navigate to the home (Job menu) screen. |
| 7 | Settings button | Quick dial to the Settings module. |
2.2 Powering Up The Tool
There are two methods available for powering up the tool:
- Via Data Cable: Plug one end of a data cable (not included) into the charging port of the tool, and the other end to a PC.
- Via Diagnostic Cable: Insert the diagnostic cable into the vehicle's DLC port. When the tool is powered on, the screen will automatically light up.
2.3 Getting Started (Initial Setup)
If it is the first time you have used this tool, you need to make some system settings:
- Press the [POWER] button to turn on the tool. The screen displays a welcome page. Tap "Start" to go to the next step.
- Choose the desired system language, and tap "Next step".
- Choose the time zone of your current location. The system will automatically configure the time according to the time zone you selected.
- The system will automatically search for all available Wi-Fi networks. Choose the Wi-Fi needed.
- After the network connection is done, tap "Next step" to configure workshop information. Input the required information, and tap "Next step" to proceed. Note: After configuration, the system will append this information to every report successfully generated.
- Carefully read all terms and conditions of the user agreement, check "Agree to all the above terms", and tap "OK" to complete the registration process. It will automatically jump to the Job Menu.
2.4 Connection to Vehicle
- Turn the vehicle's ignition off.
- Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to Section 1.5 for typical locations.
- Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end to the DB-15 diagnostic connector of the tool. Then tighten the captive screws.
Notes:
- A plastic DLC cover may be found for some vehicles; remove it before plugging the diagnostic cable.
- The cable connector is keyed and will only fit one way. If you have problems connecting, rotate the connector 180° and try again.
- Turn the ignition on. The engine can be off or running.
Caution: Do not connect or disconnect any test equipment with ignition on or engine running.
3. Operating Instructions
3.1 System Diagnosing
This function is designed to diagnose electronic control systems of a single vehicle model.
Notes:
- The diagnostic software includes various reset functions; these can be performed directly from the "Special function" list.
- All software is updated periodically. It is recommended to update to the latest version for optimal service and experience.
- Use and update of pre-installed diagnostic software is free forever.
- Use and update of diagnostic software purchased from the "Mall" is free for one year. Renewal is required after expiration.
- More vehicle coverage can be extended by subscribing in the "Mall".
3.1.1 Smart Diagnosis (Auto-Detect)
This function allows quick access to electronic control systems by decoding the VIN, bypassing manual menu selection. After connection, turn the ignition key on, and the system enters auto-detect mode.
Notes:
- Ensure "Automatic detection on connect" in "Settings" is ON.
- A stable network connection is recommended for successful VIN access.
A. Successful VIN Acquisition: If the system successfully obtains the VIN, it will scan vehicle systems. Upon completion, a diagnostic report will be automatically generated in Settings > Data > Diagnostic Report.
B. Failed VIN Acquisition: If the tool fails to access VIN information, a screen will appear prompting manual VIN input. Input the VIN and tap "OK" to proceed with Smart Diagnosis or enter Manual Diagnosis mode.
3.1.2 Manual Diagnosis
If VIN information cannot be obtained or analyzed, you can perform Manual Diagnosis. In this mode, follow on-screen instructions to select vehicle manufacturer, model, and system.
Notes:
- Before diagnosing, ensure the corresponding vehicle manufacturer software is installed.
- The diagnostic menu may vary by vehicle make, model, and year.
Diagnostic Flowchart:
- Select "Diagnose"
- Select Vehicle Manufacturer
- Select Vehicle Model
- Select Scan Mode (Automatic System Detection or Manual System Detection)
- Select Test Function (Special Functions, Read Data Stream, Clear Fault Code, Read Fault Code, Read Version Information)
Example (DEMO V15.34):
- Select diagnostic software version: Tap "DEMO".
- Select vehicle model (varies with different versions): Select the desired vehicle model.
- Turn the ignition key to ON.
- Read vehicle information: Double-check if the vehicle information is correct. Tap "Yes" to continue.
- Select test item: Choose the desired test item to proceed (e.g., Health Report, System Scan, System Selection).
3.1.3 Diagnostic Functions
A. Health Report (Quick Test): This function quickly accesses all electronic control units (ECUs) and generates a detailed report on vehicle health. Tap "Health Report" to start scanning. Fault codes are indicated by a red cross, and OK systems by a green tick.
- Report: Tap to save the diagnostic result as a report.
- Clear Code: Tap to clear existing diagnostic trouble codes.
B. Read Fault Code: Displays detailed information of DTC records retrieved from the vehicle's control system.
Notes:
- Retrieving DTCs is only part of troubleshooting. Always follow testing procedures and flow charts in the vehicle's service manual.
- Help: View help information.
- Code Search: Search for more information about the current DTC online.
- Report: Save current data in text format. Access reports from Settings > Data > Diagnostic Report.
C. Clear Fault Code: Erases codes from the vehicle after repairs. Ensure ignition key is ON and engine is OFF before performing.
Notes:
- Do NOT erase codes if taking the vehicle to a Service Center, as valuable information might be lost.
- Clearing DTCs does not fix the problem. If repairs are not made, codes will reappear.
D. Read Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU.
- Select All/Unselect: Select/deselect all data stream items.
- OK: Confirm selection.
- Value: Displays parameters with numbers and lists.
- Graph: Displays parameters with wave patterns.

Image: Screenshot of the diagnostic tool displaying 4-in-1 live data graphing for Audi/VW/Skoda.
- Combine: Merge graphs for easier comparisons (max 4 items).
- Report: Save current data as a diagnostic report.
- Record: Record and save Live Data for troubleshooting.
E. Special Functions: Offers coding, reset, relearn, and other service functions to restore vehicle functionality after repair or replacement. Available tests vary by vehicle manufacturer, model, and year.

Image: Visual representation of various free service functions, such as ABS Bleeding, Injector Coding, Battery Match, Gear Learning, Sunroof Initialization, Oil Reset, TPMS Reset, and Throttle Calibration.

Image: Key programming functions (All Key Lost, Add New Key, Disable & Delete Key, Anti-theft Module Matching) and bi-directional (active test) functions like turning lights on/off, injector buzz test, operating mirrors, A/C activation, and radiator fan control.
3.2 OBD II Diagnosis
This function provides a quick way to check for DTCs, isolate MIL causes, check monitor status for emissions testing, and verify repairs.
After connecting the tool to the vehicle's DLC, tap "OBD II" in the Job Menu. The tool will automatically detect the communication protocol and display Monitor Status. Tap "OK" to see the function list:
- Read Codes: Identifies the section of the emission control system that has malfunctioned.
- Erase Codes: Erases codes after retrieval and repairs. Ensure ignition is ON and engine is OFF.
- I/M Readiness: Checks if emissions-related systems are operating properly and are ready for Inspection and Maintenance testing. Also confirms repair effectiveness.
- Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU.
- View Freeze Frame: Takes a snapshot of operating conditions when an emission-related fault occurs. Note: Freeze Data may not be stored if DTCs were erased.
- O2 Sensor Test: Retrieves O2 sensor monitor test results.
- On-board Monitor Test: Retrieves test results for emission-related powertrain components not continuously monitored.
- EVAP System Test: Initiates a leak test for the vehicle's EVAP system. Refer to the vehicle's service manual for procedures.
- Vehicle Info: Retrieves information from the vehicle's on-board computer, including VIN, CID (Calibration ID), and CVN (Calibration Verification Number).
3.3 History
The tool records details of each diagnostic session. The History function provides direct access to previously tested vehicles, allowing users to resume operations without starting from scratch. All diagnostic records are listed in date sequence.
4. Maintenance
4.1 Upgrade
This function allows you to update the diagnostic app and software. All software is updated periodically, and it is recommended to install the latest version for best service and experience.
- Use and update of diagnostic software pre-installed on the tool is free of charge forever. No subscription renewals are required.
- Use and update of diagnostic software purchased in the "Mall" is free of charge for one year. If the free period is due, user needs to renew the subscription.
Note: Ensure a strong and stable Wi-Fi connection while updating.
4.1.1 Update Diagnostic Software & App
Tap "Upgrade" on the Job menu to enter the update center. By default, all diagnostic software is selected. To deselect specific software, tap "Unselect" and uncheck the box next to the vehicle model. Tap "Update" to start downloading. Once downloaded, software packages will be installed automatically.
4.1.2 Renew Subscription
When the free period for diagnostic software expires, it will be locked. To unlock it, you need to renew the subscription. Tap "Upgrade" on the Job menu, select the desired diagnostic software (displayed in gray), and tap "Renew". Input the 24-digit pin code from your Subscription Renewal Card (purchased from the seller or local dealer) and tap "Submit" to finish the renewal. The latest diagnostic software will then be ready for use.
Note: A single Subscription Renewal Card is applicable to only one software, not all software installed on the tool.
4.2 Clean Up
This option allows you to clear cache files and free up storage space.
4.3 Firmware Fix
Use this module to upgrade and fix diagnostic firmware. During this process, do not cut power or switch to other interfaces.
5. Troubleshooting (FAQ)
Here are some frequently asked questions and answers related to this tool:
- System halts when reading data stream. What is the reason?
It may be caused by a slackened connector. Turn this tool off, firmly connect the connector, and switch it on again. - Screen of the tool flashes at engine ignition start.
Caused by electromagnetic disturbing, this is a normal phenomenon. - There is no response when communicating with on-board computer.
Confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is at proper temperature. - What to do if the system fails to start auto VIN detection?
Check the following possible reasons:- Whether the tool is properly connected to the vehicle's DLC port.
- Whether the “Automatic detection on Connect" switch is OFF. If yes, slide it to ON.
- Why are there so many fault codes?
Usually, it's caused by poor connection or fault circuit grounding. - How to upgrade the system?
- Switch the tool on and ensure a stable internet connection.
- Tap "Settings" on the Job Menu, select "About" > "Version", and tap "Detect the System Version" to enter the system upgrading page.
- Follow the on-screen instructions step by step to finish the process. It may take several minutes depending on the internet speed. After upgrade is successfully finished, the tool will automatically restart and enter the Job menu.
6. Specifications
| Feature | Specification |
|---|---|
| Screen | 4" touch screen with a resolution of 480*800 |
| CPU | 1.3 GHz Quad-Core |
| Operating System | Android 8.1 |
| RAM | 2 GB |
| ROM (Storage) | 32GB (system shows 24.31 GB) |
| Wi-Fi | 802.11b/g/n 2.4GHz & 5 GHz |
| OBD II Input Voltage Range | 9V-18V |
| Power Up Via | DC 5V data cable (not included) or Diagnostic cable through vehicle's DLC |
| Battery | 3000mAh (Batteries Included: Yes) |
| Working Temperature | -10 to 50°C (14 to 122°F) |
| Storage Temperature | -20 to 70°C (-4 to 158°F) |
| Item Weight | 0.63kg |
| Item Dimensions (L x W x H) | 6.3inch x 3.5inch x 1inch |
| Main Cable Length | Approx. 117 cm |
| External Testing Certification | CE |
| Software Version | 2026 Version |
| Hardware Version | 2026 Version |
| Update Method | Via Wi-Fi |
| Communication Interface | OBD-II |
| Wireless Support | Wifi |
7. User Tips
- This tool excels in coding and adaptation functions, performing them quickly and efficiently.
- It is highly recommended for individuals who wish to perform car maintenance at home without needing to be a specialist, potentially saving significant money on service trips.
- Users have successfully performed injector coding on specific vehicle models like the Mercedes CLA180d X117 2017.
8. Warranty & Support
8.1 Warranty Information
This warranty is expressly limited to persons who purchase LAUNCH® products for purposes of resale or use in the ordinary course of the buyer's business.
LAUNCH® electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with stipulated procedures.
8.2 Order Information (for Parts)
Replaceable and optional parts can be ordered directly from your authorized tool supplier. Your order should include the following information:
- Quantity
- Part number
- Item description
8.3 Customer Service
If you have any questions on the operation of the unit, please contact the seller, or contact LAUNCH TECH CO., LTD.:
- Website: www.x431.com, www.cnlaunch.com
- Phone: +86 755 2593 8674
- Email: DOD@cnlaunch.com