LAUNCH CRP123E V3.0

Contents

LAUNCH CRP123E V3.0 OBD2 Scanner User Manual

Model: CRP123E V3.0

Brand: LAUNCH

1. Overview

The LAUNCH CRP123E V3.0 is a professional diagnostic tool designed for car owners and DIYers. It offers comprehensive diagnostics for four main systems (Engine, Transmission, ABS, SRS) and includes seven essential reset services. This device features a 5-inch touchscreen, Android 8.1 operating system, and supports lifetime free updates via Wi-Fi.

LAUNCH CRP123E V3.0 OBD2 Scanner with carrying case

Figure 1: LAUNCH CRP123E V3.0 OBD2 Scanner and carrying case.

1.1 Vehicle Coverage

This diagnostic tool is specifically designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN). It covers 90+ brands and 10000+ vehicle models from 1996-2026, spanning Asia, Europe, and USA.

Vehicle coverage map showing American, European, and Asian areas with supported car brands and special protocols like CAN-FD, DOIP, FCA AutoAuth

Figure 2: Global vehicle coverage and supported protocols.

1.2 OBD II Definitions

The OBD II system monitors emission control systems and key engine components. Key terms include:

  • EOBD: European On-Board Diagnostics, similar to OBD II.
  • Communication Protocols: Allows different systems and sensors to communicate. Includes CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
  • PCM: Powertrain Control Module, the vehicle's on-board computer.
  • DLC: Data Link Connector, the 16-cavity connector for diagnostic tools.
  • MIL: Malfunction Indicator Light, the 'Check Engine' warning light.
  • DTC: Diagnostic Trouble Code, a code stored in the computer's memory indicating a fault.
  • Freeze Frame Data: Operating conditions stored when a DTC is set.
  • PID: Parameter Identification Data, data returned by control modules.
  • Monitors: Diagnostic routines run by the PCM to test emissions-related components.
  • Enabling Criteria: Vehicle-specific conditions required for monitors to run.
  • Trip: A driving sequence that meets enabling criteria for a specific monitor.
  • Warm-up Cycle: Vehicle operation where engine temperature rises to specific levels, used by PCM to erase codes automatically if no faults are detected.
  • Fuel Trim (FT): Feedback adjustments to the fuel schedule (short-term and long-term).

1.3 Diagnostic Trouble Codes (DTCs)

OBD II DTCs are five-digit alphanumeric codes indicating problems. The first character identifies the main system (P=Powertrain, B=Body, C=Chassis, U=Network). The second character indicates code type (0=Generic, 1=Manufacturer Specific). The third character identifies the specific system or sub-system, and the fourth/fifth characters identify the malfunctioning section.

DTC Example P0201 diagram showing breakdown of code structure and meaning

Figure 3: Example of a Diagnostic Trouble Code (DTC) structure.

2. Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the tool, read this user’s manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:

  • This tool contains an internal Lithium Polymer battery. Do not disassemble, crush, pierce, or dispose of the battery in fire or water to reduce the risk of fire or burns.
  • This product is not a toy. Keep away from children.
  • Do not expose the device to rain or wet conditions.
  • Do not place the device on any unstable surface.
  • Never leave the device unattended during charging. Place on a non-flammable surface.
  • Handle the device with care. If dropped, check for breakage.
  • Do not operate the tool in explosive atmospheres (flammable liquids, gases, heavy dust).
  • Keep the tool dry, clean, and free of oil, water, or grease. Use a mild detergent on a clean cloth for cleaning.
  • People with pacemakers should consult their physician(s) before use due to potential electromagnetic interference.
  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle, as this can cause driver distraction and fatal accidents.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, and other objects away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area. Exhaust gases are poisonous.
  • Chock the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs, as these components create hazardous voltages when the engine is running.
  • Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Don't connect or disconnect any test equipment while the ignition is on or the engine is running.

3. Compliance Information

FCC ID: XUJCRP123XV3

IC: 29886-CRP129IV3

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Innovation, Science and Economic Development Canada's licence-exempt RSSs and part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference; and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

3.1 Specific Absorption Rate (SAR) Information

This product meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

3.2 RF Exposure Information and Statement

The SAR limit is 1.6 W/kg averaged over one gram of tissue. This device has also been tested against this SAR limit. This device was tested for typical body-worn operations 0mm from the body. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body.

3.3 Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user's body, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

This device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The RF frequencies can be used in Europe without restriction.

4. Product Descriptions

4.1 Components & Controls

Diagram of the CRP123E V3.0 showing numbered components: 1. Charging LED, 2. LCD, 3. USB Type-C port, 4. DB-15 Diagnostic Connector, 5. Power Button

Figure 4: CRP123E V3.0 Components and Controls.

  1. Charging LED: Red indicates charging, Green indicates fully charged.
  2. LCD: Displays test results and user interface.
  3. USB Type-C port: Connects to the charging cable.
  4. DB-15 Diagnostic Connector: Connects to the vehicle's DLC.
  5. Power Button: Turns the tool on or off.

4.2 Technical Specifications

AttributeSpecification
Screen5" touch HD screen (1280*720P Resolution)
Operating SystemAndroid 8.1
CPU1.3GHz 4CORE
RAM2GB
ROM (Memory)32GB (system displays 25.9GB)
Battery6100mAh
Communication InterfaceOBD-II
Wireless SupportWifi (5G & 2.4G)
OBD II interface input voltage9V~18V
Charging viaDC 5V charging cable or diagnostic cable through vehicle's DLC
Operating temperature0°C to 50°C (32°F to 122°F)
Storage temperature-20°C to 70°C (-4°F to 158°F)
Charging temperature0°C to 40°C (32°F to 104°F)
Dimensions228 mm x 125 mm x 34 mm (250*175*75mm in some descriptions)
Item TypeCode Readers & Scan Tools
CertificationCE
Language SupportEnglish, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Spanish
Free Update PeriodLifetime Free Update Via Wifi
Warranty5 Year

Note: The operating temperature refers to the temperature at which the scan tool works normally in non-charging status.

Elite Hardware specifications including Android 8.1, 1.3GHz 4CORE CPU, Lifetime Update, 2G+32GB RAM+ROM, 5 inch Touchscreen, 6100mAh Battery, 1280x720P Resolution, 5G & 2.4G Wifi, Type-C

Figure 5: Hardware specifications and key features.

4.3 Packing List

The following packing list is for reference only. For details, consult the seller or check the packing list supplied with this tool together.

  1. Diagnostic tool x 1 (CRP123E V3.0)
  2. OBD II diagnostic cable x 1
  3. Charging cable x 1
  4. User manual x 1
  5. Carrying bag x 1
Image showing the contents of the product package: CRP123E device, carrying bag, OBDII cable, charging cable, and user manual.

Figure 6: Package contents.

5. Setup

5.1 Charging the Tool

There are two charging methods available:

  • Via Charging Cable: Plug one end of the included charging cable into the Type-C port of the tool, and the other end to an external power supply device.
  • Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle's DLC.

Once the charging LED illuminates solid green, the battery is fully charged.

5.2 Getting Started (Initial Setup)

If it is the first time you have used this tool, you need to make some system settings:

  1. Press the power button to turn it on.
  2. The screen displays a welcome page. Tap Start to proceed.
  3. Choose the desired system language, and tap Next step.
  4. Choose the desired time zone, and tap Next step to enter the WLAN setup screen.
  5. Slide the switch to ON. The system starts searching for all available wireless LANs. Choose the desired WLAN access point/network.
    • If the selected network is open, you can connect directly.
    • If the selected network is encrypted, enter the security key (network password).
  6. After the network connection is done, tap Next step to configure workshop information. Input the required information, and tap Next step to continue. (Note: Once configured, workshop information is automatically added to reports.)
  7. Carefully read all terms and conditions of the user agreement, check the box before Agree to all the above terms, and tap OK to finish the sign-up process and navigate to the Job Menu.

6. Operating Instructions

6.1 Job Menu

The main menu screen includes the following function modules:

ModuleDescription
Local DiagnoseConfigures the tool as a professional diagnostic tool.
Service FunctionOffers coding, reset, relearn, and other service functions to restore vehicle functionality.
Other ModulesIncludes add-on modules to extend diagnostic tool functionalities.
UpgradeUpdates vehicle diagnostic software and APK. (Requires stable network connection)
MallSubscribes to extra vehicle diagnostic software or reset software not included.
Know Your CustomerAssists repair shops with business analysis, customer management, diagnosis statistics, and service ranking.
MineChecks saved reports, order information, and system settings.
ToolboxProvides practical add-on modules: battery voltage, diagnostic software clear, firmware fix, DTC library, diagnostic record, DLC lookup, feedback, image, user manual.
MoreIncludes Online support and LAUNCH Academy.

6.2 Diagnose

  1. Turn the ignition off.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC). (Refer to Figure 7 for common locations).
  3. Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end to the DB-15 diagnostic connector of the tool. Tighten the captive screws.
  4. Turn the ignition on. The engine can be off or running.
  5. Press the power button for several seconds to turn the tool on and enter the Job Menu.
Diagram showing common locations of the Data Link Connector (DLC) in a car interior.

Figure 7: Common DLC locations.

Notes:

  • A plastic DLC cover may need to be removed.
  • The cable connector is keyed and fits only one way.

6.2.1 System Diagnostics

This function diagnoses electronic control systems of a single vehicle model. Supported systems and functions vary by product configuration.

Video 1: Product demonstration of the LAUNCH CRP123E V2.0 Elite Professional, highlighting its diagnostic capabilities and features.

Smart Diagnosis (Auto-Detect)

Quickly accesses electronic control systems by decoding the Vehicle Identification Number (VIN). Set Automatic detection on connect to On in Mine -> Settings. After connection and ignition on, the system enters auto-detect mode.

Alternatively, tap Local Diagnose -> AutoDetect if auto-detection is off.

Notes:

  • A stable network connection is recommended for VIN access.
  • If auto-detection fails, try connecting to the network. Not all cars support Auto-Detect.
  • If VIN is successfully obtained, confirm and tap OK to start diagnosis. A diagnostic report will be generated.
  • If VIN access fails, the tool enters Manual Diagnosis mode.
Manual Diagnosis

If VIN cannot be obtained, perform diagnosis manually by executing menu-driven commands and following on-screen instructions.

Notes:

  • Ensure corresponding vehicle manufacturer software is installed.
  • Diagnostic menu varies by vehicle make, model, and year.
Flowchart for manual diagnosis process: Select Local Diagnose, Vehicle Manufacturer, Vehicle Model, Scan Mode (Automatic or Manual), and Test Function (Read Version, Read Fault Code, Clear Fault Code, Read Data Stream).

Figure 8: Manual diagnosis flowchart.

To perform manual diagnosis:

  1. Select diagnostic software version (e.g., "DEMO").
  2. Select vehicle model.
  3. Select test item (e.g., Read Version Information, Read Fault Code, Clear Fault Code, Read Data Stream).
Health Report (Quick Test)

Quickly accesses all electronic control units and generates a detailed vehicle health report. Tap Health Report on the test item selection screen. Fault codes appear in red, normal systems in green.

On-Screen Buttons:

  • Enter: Select other test functions.
  • Report: Save diagnostic result as a report (accessible via Mine -> My Report).
  • Clear Code: Clear existing diagnostic trouble codes.
System Scan

Quickly scans which systems are installed on the vehicle.

System Selection

Manually select the test system and function step-by-step. Tap System Selection, then the desired system (e.g., Engine System) to enter the test function selection screen.

Read Fault Code

Displays detailed information of DTC records. Tap Read Fault Code on the test function selection screen.

Notes: Do not replace parts based solely on DTC definitions. Always consult the vehicle's service manual for proper testing procedures.

Read Live Data Stream

Retrieves and displays live data and parameters from the vehicle's ECU. Tap Read Data Stream on the test function selection screen. Data can be viewed in three modes:

  • Value: Displays parameters as numbers and lists.
  • Graph: Displays parameters with wave patterns.
  • Combine: Merges graphs for easier comparisons (up to 8 data stream items).

On-Screen Buttons:

  • Select All: Selects all items on the current page.
  • Unselect: Deselects all data stream items.
  • OK: Confirms selection and proceeds.
  • Record: Records and saves Live Data (accessible via Toolbox -> Diagnostic Record).
Freeze Frame

Takes a snapshot of operating conditions when an emission-related fault occurs.

O2 Sensor Test

Retrieves and displays O2 sensor monitor test results.

On-Board Monitor Test

Retrieves and displays test results for emission-related powertrain components and systems not continuously monitored.

Read Vehicle Information

Retrieves VIN, Calibration ID (CID), and Calibration Verification Number (CVN).

Component Test

Actuates certain vehicle components via commands from the scanner to test operability.

I/M Readiness

Checks if emissions-related systems are operating properly and ready for inspection/maintenance testing.

History

Provides direct access to previously tested vehicles and diagnostic records, sorted by date.

6.3 Service Function (7 Reset Services)

The tool offers various reset and relearn functions to help vehicles return to functional status after repair or replacement. Available functions are subject to change; regular updates are recommended.

Image showing 7 Special Functions: Oil Reset, Brake Reset, DPF Reset, ABS Bleeding, Battery Matching, Steering Angle Reset, Electronic Throttle Relearn.

Figure 9: Seven essential reset services.

To perform a reset service:

  1. Select Service Function from the Job Menu.
  2. Choose the desired service function.
  3. Select the desired car brand.
  4. Select the reset mode (Manual Reset or Auto Reset).
  5. Follow the on-screen instructions to proceed.

The 7 Reset Services include:

  • Oil Lamp Reset: Resets the Oil Life Reminder and switches off the Oil Light after engine oil replacement.
  • EPB Reset (Brake Reset): Resets the electronic parking brake system after brake pad replacement or maintenance.
  • Steering Angle Calibration (SAS Reset): Clears fault steering angle sensor memories, sets the steering angle to zero, and turns off the steering wheel warning light.
  • Battery Matching (BMS Reset): Performs a resetting operation on the vehicle battery's monitoring unit after battery replacement.
  • ABS Bleeding: Performs brake operation to remove air from the brake fluid pipeline when changing brake fluid.
  • D.P.F Regeneration: Clears PM (Particulate Matter) from the DPF filter through continuous combustion oxidation.
  • Throttle Relearn (ELEC.THROTTLE RLR): Makes initial settings to throttle actuators for smooth driving after throttle body replacement or cleaning.

Warm Tips: To successfully clear fault codes, you may need to repair the car first. If the scan tool cannot work on your car, please reach out to customer support with car details (make/model/year and VIN).

6.4 Toolbox Functions

The Toolbox module provides several utility functions:

  • Battery Voltage: Measures the current voltage of the vehicle's battery.
  • Diagnostic Software Clear: Deletes diagnostic software that is not frequently used.
  • Firmware Fix: Upgrades and fixes diagnostic firmware. Do not cut power or switch interfaces during this process.
  • DTC Library: Retrieves detailed descriptions of DTCs from the database. Swipe up/down to alter values, then press OK to view definitions.
  • Diagnostic Record: Stores running parameters or waveform graphs recorded by the user. Tap to select desired data stream items and OK to jump to playback.
  • DLC: Helps locate the vehicle's DLC.
  • Feedback: Allows sending diagnostic problems for analysis and troubleshooting.
  • FAQ: Lists frequently asked questions and answers.
  • Image: Manages or shares screenshots.
  • Product Manual: Provides a detailed operation manual integrated into the tool.

7. Maintenance

7.1 Upgrade

If new software or APK updates are available, a numeric indicator will display on the Upgrade module in the Job Menu. Use this option to keep the tool synchronized with the latest version.

Notes:

  • Regular updates are strongly recommended for new functions and better service.
  • This function requires a stable network connection.

To update:

  1. Tap Upgrade on the Job Menu to enter the update center.
  2. By default, all diagnostic software is selected. To deselect specific software, tap Unselect and uncheck the box next to the vehicle model.
  3. Tap Update to start downloading. This may take several minutes. Tap Stop to pause, Continue to resume. If network connection fails, tap Retry.
  4. Once downloaded, software packages will be installed automatically.

The free subscription for default software can be viewed by checking the expiration date. Renewal is required after expiration. Without subscription, new diagnostic software and versions (except downloaded software) are restricted.

7.2 Mall Function

This function allows you to subscribe to additional vehicle diagnostic software and reset software not pre-installed on the tool. The mall offers full systems and functions (excluding online programming and coding). Different software has different pricing.

Tap Mall to open the online software mall. Select the target software and follow on-screen instructions to complete the transaction.

Note: Software activates immediately upon purchase and is generally non-refundable. Double-check order details before payment. Subscribed software is free for one year; renewal is required after expiration.

Image showing the Online Mall interface on the CRP123E V3.0, with options to purchase reset functions and full system diagnoses.

Figure 10: Online Mall for additional functions.

7.3 Mine (Settings)

The Mine module allows you to manage reports, orders, and system settings:

  • My Report: Check and manage saved diagnostic reports, sorted by date and make. Use the search icon to filter.
  • My Order: Check order information.
  • Settings: Customize tool preferences:
    • Units of measurement: Set to Metric or English System.
    • Screen capture: Enable/disable the screenshot icon. When ON, a screenshot icon floats on the upper right corner.
    • Automatic detection on connect: Enable/disable automatic VIN detection upon connection.
    • Display/Brightness: Set standby time and screen brightness. (Reducing brightness conserves power).
    • Sound: Adjust volume and other sound settings.
    • Network: Register the tool, update software/APK, and send emails via WLAN.
    • Time zone: Set the device's time zone.
    • Language: Change the system language.
    • Workshop information: Configure workshop details (automatically added to reports).
    • Recovery: Reset the tool to default factory settings. (Warning: May cause data loss).
    • Clean up: Clear cache files and free up storage space.
    • About: Displays hardware configuration and license agreement.

7.4 Other Modules

These modules extend diagnostic tool functionalities. Currently, only the BTS (Bluetooth Battery Tester) test is available, requiring a separately sold Bluetooth battery tester for faster and easier battery detection.

8. User Tips

  • Vehicle Compatibility: While the CRP123E V3.0 supports a wide range of vehicles (90+ brands, 1996-2026), specific reset functions may not be supported for all car models. Always verify compatibility with the seller or manufacturer for critical functions before purchase, especially for diesel engines or less common brands.
  • Software Updates: Take advantage of the lifetime free updates via Wi-Fi. Regularly updating the software ensures you have the latest features, bug fixes, and expanded vehicle coverage. A stable internet connection is crucial for successful updates.
  • Diagnostic Reports: Utilize the diagnostic report feature to save and share results. This can be very helpful for tracking vehicle health over time or for consulting with a mechanic. Reports can be accessed via Mine -> My Report.
  • Battery Management: Monitor the real-time battery voltage of your vehicle using the tool. This can help identify potential battery issues early.
  • Troubleshooting Fault Codes: When a fault code appears, remember that clearing the code does not fix the underlying problem. Always diagnose and repair the cause of the fault before clearing codes to prevent them from reappearing.
  • Language Settings: The device supports 11 languages. Easily switch to your preferred language (English, Spanish, French, German, Italian, Russian, Japanese, Korean, Portuguese, Polish) in the settings to overcome language barriers.
  • Manual VIN Entry: If the auto-VIN scan fails, you can manually enter the Vehicle Identification Number. Ensure accurate entry for correct vehicle identification.
  • Customer Support: If you encounter issues or have questions about specific vehicle compatibility or functions, contact LAUNCH customer service. Provide detailed information about your car (make, model, year, VIN) and the issue for efficient support.

9. Warranty and Support

9.1 Warranty

This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.

LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user.

This warranty does not cover any part that has been abused, altered, used for a purpose other than which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects shall be made by LAUNCH in accordance with established procedures. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.

9.2 Customer Service

If you have any questions on the operation of the unit, contact the seller, or contact LAUNCH TECH Service Center:

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.