1. Introduction
The MOES NA503B Series Multi-Gas & Smoke Detector is a versatile safety device designed to monitor various hazardous conditions in your home or workplace. Depending on the model purchased, it can detect Carbon Monoxide (CO), combustible gases, and/or smoke, while also displaying real-time temperature and humidity. This manual provides essential information for the proper installation, operation, and maintenance of your detector.
Note: The product is available in EU and US plug versions. Each plug version comes in 4 models, and the types of gases detected vary by model. Please confirm the model before purchase.

Available Models:
- CO Detector
- CO & Combustible Gas Detector
- CO & Smoke Detector
- CO & Combustible Gas & Smoke Detector

Packing List:
- NA503B Detector Unit (X1)
- User Manual (X1)
- Plug (X1)
- Packaging Lining (X1)
2. Setup and Installation
2.1 Powering the Device
The detector is designed for easy plug-and-play operation. Simply plug it into a standard electrical socket. It also features a built-in 1000mAh battery for temporary power supply, ensuring continuous monitoring during power outages.


2.2 Detachable Plug
The plug is detachable from the main detector unit, offering flexibility. This allows you to temporarily move the detector to different locations as needed, without having to unplug the entire unit from the wall.

2.3 Placement and Applicable Environments
For optimal performance and safety, place the detector in areas where CO, combustible gases, or smoke may accumulate. Consider the following applicable environments:
- Kitchens: Near gas stoves or other gas-burning appliances.
- Bedrooms: For personal safety during sleep.
- Basements: Where furnaces, water heaters, or other fuel-burning appliances are located.
- Garages: Especially if vehicles are idled inside, to detect vehicle exhaust.
- Near Water Heaters and Fireplaces: Sources of potential CO leaks.


3. Operation
3.1 Device Screen and Button Features
The detector features a clear LED display and intuitive buttons for control and information display. The specific features displayed may vary slightly depending on your model (e.g., CO only vs. multi-gas/smoke).


3.2 Alarm System and Indicator Lights
The detector provides both sound and light alarms to alert you to potential dangers. The alarm sound level is ≥85dB.

A three-level indicator light system provides a quick visual guide to the current safety status:
- Green: Safe Level
- Yellow: Danger Level (Warning)
- Red: Alarm Level (Immediate Danger)

3.3 Precise Detection Technology
The detector utilizes electrochemistry for precise detection. The displayed data is for reference only, and actual detection thresholds may vary depending on the equipment model and environment.

3.4 Brightness Adjustment
You can manually adjust the display brightness to one of three levels (0%, 50%, 100%) for comfortable viewing in various lighting conditions.

4. Maintenance
Regular maintenance ensures the longevity and accuracy of your detector.
- Self-Test: Periodically press the Power/Self-Test button to ensure the alarm and display functions are working correctly. Refer to the device screen and button features diagram for button location.
- Cleaning: Gently wipe the exterior of the detector with a soft, dry cloth. Do not use cleaning sprays, polishes, or solvents.
- Ventilation: Ensure the detector's vents are not blocked by dust or debris.
- Battery Check: The built-in battery provides backup power. While the device is primarily plug-in, ensure it is connected to a power source for optimal operation and battery charging.
5. Troubleshooting
If you encounter issues with your MOES detector, please refer to the following common troubleshooting steps:
- No Display/No Power: Ensure the device is securely plugged into a working electrical outlet. Check the power outlet with another appliance. If using battery backup, ensure the battery is charged.
- False Alarms: Ensure the detector is not placed near sources of steam, cooking fumes, or excessive humidity, which can trigger smoke or gas alarms. Avoid placing it directly above or next to gas appliances.
- Alarm Sounds Continuously: If the alarm sounds and there is no apparent hazard, ventilate the area thoroughly. If the alarm persists, contact emergency services if you suspect a real danger. If it's a false alarm, consider relocating the detector.
- Inaccurate Readings: Ensure the detector is placed in an appropriate environment as described in Section 2.3. Avoid areas with extreme temperatures or humidity outside the specified operating range.
- Buttons Unresponsive: Unplug the device for a few minutes, then plug it back in to perform a soft reset.
If problems persist after attempting these steps, please contact customer support for further assistance.
6. Specifications
The MOES NA503B series detectors come in various configurations. Please refer to the specifications for your specific model:
General Specifications:
| Feature | Specification |
|---|---|
| Brand Name | MOES |
| Origin | Mainland China |
| Certification | CE |
| Input | 100-240V 50/60Hz Replaceable |
| Shell Material | Flame Retardant ABS Plastic |
| Work Temperature | -10°C~50°C / 14°F~122°F |
| Alarm | Yes (≥85dB) |
| Product Size (Excluding plug) | 125.5 x 60.5 x 36.3 mm (4.945 x 2.38 x 1.43 in) |

Model-Specific Specifications:
| Feature | CO Detector | CO & Smoke Detector | CO & Gas Detector | CO & Gas & Smoke Detector |
|---|---|---|---|---|
| Carbon Monoxide (CO) | 0~999PPM (±10%) | 0~999PPM (±10%) | 0~999PPM (±10%) | 0~999PPM (±10%) |
| CO Alarm Threshold | 49 PPM (Initial Default) | 49 PPM (Initial Default) | 49 PPM (Initial Default) | 49 PPM (Initial Default) |
| Temperature Measurement Range | -10°C~50°C (±1.5°C) / 14°F~122°F (±2.7°F) | N/A | N/A | N/A |
| Humidity Measurement Range | 0%-95% RH (±5%), non-condensing | 0%-95% RH (±5%), non-condensing | 0%-95% RH (±5%), non-condensing | 0%-95% RH (±5%), non-condensing |
| Smoke Sensor | N/A | Photoelectric | N/A | Photoelectric |
| Smoke Alarm Threshold | N/A | ≥ 0.15 dB/m | N/A | ≥ 0.15 dB/m |
| Combustible Gas Level | N/A | N/A | GAS Lv1-3 (Lv3: ≥15% LEL) | GAS Lv1-3 (Lv3: ≥15% LEL) |
| Gas Alarm Threshold | N/A | N/A | GAS Lv2 (≥5% LEL) | GAS Lv2 (≥5% LEL) |
7. User Tips
- Optimal Placement: For CO detection, place the unit at knee to chest height. For smoke, higher on the wall or ceiling is generally better. For gas, near the source of potential leaks but not directly above it.
- Regular Testing: Make it a habit to test your detector monthly using the self-test button.
- Ventilation: If an alarm sounds, immediately ventilate the area by opening windows and doors. Evacuate if necessary and call emergency services.
- Avoid Obstructions: Ensure nothing blocks the detector's vents or the path of smoke/gas to the sensor.
8. Warranty and Support
MOES products are designed for reliability and performance. For warranty information, technical support, or any inquiries regarding your detector, please contact the MoesHouse Official Store directly. You can find their contact information on the product's purchase page or through their official store on AliExpress.