Hobbywing RTF F7 8S Lite FC, 80A/100A 4in1 4-8S Lite AT 32-bit PWM,DSshot300/600 ESC

Contents

Hobbywing RTF F7 8S Lite Flight Controller and 4-in-1 ESC Instruction Manual

Model: RTF F7 8S Lite FC, 80A/100A 4in1 4-8S Lite AT 32-bit PWM,DSshot300/600 ESC

Brand: Hobbywing

1. Introduction

This manual provides detailed instructions for the Hobbywing RTF F7 8S Lite Flight Controller (FC) and the accompanying 80A/100A 4in1 4-8S Lite AT 32-bit Electronic Speed Controller (ESC). These components are designed for high-performance FPV drone applications, offering advanced features and robust power delivery. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.

Hobbywing Flight Controller and 4-in-1 ESC stacked, showcasing the compact design.

Hobbywing Flight Controller and 4-in-1 ESC stacked, showcasing the compact design.

Product overview video demonstrating the physical components and their assembly.

2. Specifications

2.1. RTF F7 FC 8S Lite (Flight Controller)

FeatureSpecification
Betaflight TargetHOBBYWING_XROTORF7CONV
Supported VTX ProtocolSmart audio & Tramp
Motor Signal OutputDefault 4 road, additional 2 road (ch5, ch6)
BlackBox Size16Mb
OSD ChipAT7456E
Board ChipHigh-Precision Barometer
Gyro ChipICM-42688
Gyro LDO SupportedNone
Main MCUSTM32F722
LED ControlYes
Beeper SupportedYes
UARTS6
BEC5V 3A & 10V 3A
Size35x35x7.7mm
Install Holes30.5x30.5mm (φM4)
Weight10g

2.2. RTF 80A 4in1 8S Lite AT (ESC)

FeatureSpecification
Continuous/Peak Current80A*4/100A*4
Input Voltage4-8S LiPo
Input WiresRed-10AWG-135MM*1, Black-8AWG-135MM*1
Output WiresNo wires but solder tabs
Input ConnectorsNo
ESC Signal Interface8Pin-SH1.0
Size56x57x7mm
Weight39g
FirmwareSelf-developed 32-bit ESC firmware
ESC ProgrammingCompatible with BLHeliSuite configuration software
Throttle Signal SupportedPWM, DSshot300/600
Bidirectional DShot SupportedSupported
Motor RotationSupported
Driving Frequency Setting48kHz
Applications15-18 inch, 4-axis FPV

2.3. RTF 100A 4in1 8S Lite AT (ESC)

FeatureSpecification
Continuous/Peak Current100A*4/120A*4
Input Voltage4-8S LiPo
Input WiresRed-8AWG-135MM*1, Black-8AWG-135MM*1
Output WiresNo wires but solder tabs
Input ConnectorsNo
ESC Signal Interface8Pin-SH1.0
Size60x57x7mm
Weight39g
FirmwareSelf-developed 32-bit ESC firmware
ESC ProgrammingCompatible with BLHeliSuite configuration software
Throttle Signal SupportedPWM, DSshot300/600
Bidirectional DShot SupportedSupported
Motor RotationSupported
Driving Frequency Setting48kHz
Applications15-18 inch, 4-axis FPV

3. Key Features

3.1. RTF F7 FC 8S Lite Features

  • Abundant Interfaces & Stable Circuitry: Designed for comprehensive connectivity and reliable performance.
  • Onboard Blackbox Chip: 16Mb Blackbox for flight data logging and analysis.
  • Powerful BEC Capabilities: Integrated 5V 3A and 10V 3A BECs for powering peripherals.
  • Plug-and-Play Slots: Simplifies connections for various components.
  • Damping Grommets Equipped: Reduces vibration for improved flight stability.
  • Built-in High-Precision Barometer: Enhances altitude hold and stability.
Detailed diagram of RTF F7 FC 8S Lite features, including interfaces, blackbox, BEC, plug-and-play slots, damping grommets, and barometer.

Detailed diagram of RTF F7 FC 8S Lite features.

3.2. RTF 80A/100A 4in1 8S Lite AT ESC Features

  • Compact & High Current Capability: Robust design for demanding FPV setups.
  • Immersion Gold-Plated Through-hole Solder Pads: Ensures reliable and strong solder connections.
  • Reduced Vibration & Extended Lifespan: Designed with damping grommets to minimize vibration transfer.
  • Bidirectional DShot & RPM Filtering: Supports advanced motor control and filtering for smoother flight.
  • High-Frequency, Low-ESR Capacitor Included: Effectively suppresses ripple and voltage spikes.
  • Integrated TVS Diode for Voltage Spike Suppression: Protects the ESC from sudden voltage fluctuations.
Detailed diagram of RTF 80A 4in1 8S Lite AT ESC features, including compact design, gold-plated solder pads, vibration reduction, DShot/RPM filtering, low-ESR capacitor, and TVS diode.

Detailed diagram of RTF 80A 4in1 8S Lite AT ESC features.

Detailed diagram of RTF 100A 4in1 8S Lite AT ESC features, including compact design, gold-plated solder pads, and vibration reduction.

Detailed diagram of RTF 100A 4in1 8S Lite AT ESC features.

4. Setup and Installation

Careful installation is crucial for the performance and longevity of your FPV system. Follow these general guidelines:

4.1. Physical Installation

  1. Mounting: Mount the FC and ESC securely using the provided damping grommets and M4 mounting holes (30.5x30.5mm spacing). Ensure proper orientation as indicated by arrows or markings on the boards.
  2. Stacking: The FC and ESC are designed to be stacked. Connect them using the included wiring harness or solder pads as appropriate.
  3. Power Connection: Solder the main battery input wires (Red and Black) to the designated large solder pads on the ESC. Ensure polarity is correct. The included low-ESR capacitor should be soldered to the main battery pads to filter power.
  4. Motor Connections: Solder motor wires to the corresponding motor pads (M1-M4) on the ESC. Double-check motor order and rotation direction.
  5. Peripheral Connections: Connect your receiver, VTX (Video Transmitter), camera, GPS, and other peripherals to the appropriate UARTs and pads on the Flight Controller. Refer to the pinout diagrams for specific connections.
Top and bottom view of the RTF F7 FC 8S Lite Flight Controller, highlighting connection pads and components.

Top and bottom view of the RTF F7 FC 8S Lite Flight Controller.

Top view of the 4-in-1 ESC, showing motor solder pads and power connections.

Top view of the 4-in-1 ESC, showing motor solder pads.

Image showing included accessories: capacitor and power wires.

Included accessories: capacitor and power wires for installation.

4.2. Software Configuration

  1. Flight Controller Firmware: Connect the FC to your computer via USB. Use the Betaflight Configurator software to flash the HOBBYWING_XROTORF7CONV target firmware.
  2. ESC Firmware: The ESC uses self-developed 32-bit firmware compatible with BLHeliSuite configuration software. Connect the ESC to your computer (usually via the FC passthrough) and configure motor settings, direction, and protocols (PWM, DShot300/600).
  3. Initial Setup: Perform initial setup in Betaflight, including accelerometer calibration, receiver setup, motor testing, and OSD configuration.

5. Operating Instructions

  1. Pre-Flight Check: Before each flight, ensure all connections are secure, propellers are correctly installed, and battery is fully charged. Verify flight mode switches and arming procedures on your radio.
  2. Arming: Arm the drone using your configured arming switch. Motors should spin up slowly.
  3. Flight: Operate the drone according to your FPV flying skills. The F7 FC provides stable flight characteristics, and the 4in1 ESC delivers smooth and responsive motor control.
  4. Disarming: Disarm the drone after landing to stop the motors.
  5. Blackbox Data: After flights, you can download Blackbox logs from the FC to analyze flight performance and troubleshoot issues.

6. Maintenance

  • Regular Inspection: Periodically inspect all solder joints and wire connections for signs of wear, corrosion, or damage.
  • Cleaning: Keep the boards clean from dust, dirt, and debris. Use compressed air or a soft brush. Avoid using liquids directly on the electronics.
  • Firmware Updates: Check for and apply firmware updates for both the FC (Betaflight) and ESC (BLHeliSuite compatible) to ensure optimal performance and access to new features.
  • Environmental Protection: If flying in damp or dusty conditions, consider conformal coating for added protection, though this is not officially supported and may void warranty.

7. Troubleshooting

  • No Power: Check main battery connection, polarity, and ensure the capacitor is correctly installed. Inspect for shorts.
  • Motors Not Spinning: Verify ESC connections to motors, check motor order in Betaflight, ensure ESC firmware is correctly configured, and calibrate ESCs if necessary. Check for bent motor shafts or damaged propellers.
  • Intermittent Connection/Signal Loss: Inspect receiver wiring, ensure proper binding, and check for interference. Verify UART settings in Betaflight.
  • Unstable Flight: Re-calibrate accelerometer, check PID tuning, ensure damping grommets are correctly installed, and inspect for physical damage to the frame or propellers. Review Blackbox logs for insights.
  • VTX/Camera Issues: Check power and signal connections to the FC. Verify VTX protocol settings (Smart audio & Tramp) in Betaflight.

8. User Tips

  • Proper Soldering: Always use a good quality soldering iron and lead-free solder. Ensure clean, strong solder joints to prevent intermittent issues and shorts.
  • Load Management: While the ESCs are robust, ensure your motor and propeller combination does not exceed the continuous current ratings to prevent overheating and damage. Consider adequate airflow for cooling.
  • Configuration Backup: Always back up your Betaflight and ESC configurations before making significant changes or firmware updates.

9. Warranty and Support

For warranty claims, technical support, or further assistance, please contact the seller or Hobbywing customer service directly. Keep your proof of purchase handy. Please note that damage due to improper installation, misuse, or unauthorized modifications may void the product warranty.

© 2023 Hobbywing. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.