1. Important Safety Information and Warnings
Please read all instructions carefully before installation and operation. Pay special attention to the ⚠ symbol, which indicates important warnings and reminders.
Important Tips:
- It is highly recommended that this machine be installed by a car audio professional.
- ⚠ Power Supply: This unit is designed for a vehicle's 12V power supply system (a grounding wire is required). Do not install this unit in a 24V vehicle, as it will cause damage.
- 🚫 Fuse: Do not repair the power fuse without professional guidance. Improper use of the fuse can cause damage to the machine or cause a fire.
- 🚫 Driving Safety: To avoid violating traffic rules, drivers must not watch videos or operate the machine while driving to prevent unnecessary accidents.
- 🚫 Professional Installation: For safety and proper product use, please have professionals install, disassemble, or repair the machine to avoid damage and accidents.
- 🚫 Environment: Avoid placing this product in a humid environment or near water to prevent fire due to electric shock or other unnecessary damage.
Note: To prevent burning out the machine, do not energize it until you have correctly connected the power cord!
2. Initial Test
Before full installation, perform a quick test to confirm the device is working normally. If the unit does not work after installation, recheck these steps.
- Combine the red and yellow wires of the car stereo and connect them to the positive pole of a 12V battery.
- Connect the black wire to the negative pole of the battery.
- After 2 seconds, check the car stereo. If the screen lights up, the car stereo is functioning properly.
3. Installation
There are generally three methods for installing the head unit. Choose the method that best suits your vehicle and situation. You may also re-install the new radio according to the original car radio's installation method.
- Screw-fixed installation
- Card position fixed installation
- Special frame fixed installation
Wiring Diagram:
Refer to the diagrams below for proper wiring connections. (Note: Images are for reference only; actual product may vary slightly.)

Figure 3.1: Main Harness Wiring Diagram

Figure 3.2: Back of Host Device Interface Diagram
Back Interface Connections:
- Power Cable
- RCA Input/Output
- Canbus serial cable
- 2 USB Cables
- Camera Input
- Radio Antenna
- GPS Antenna
Rear View Camera Wiring (Optional):
If you are installing a rear view camera, follow the diagram below. Ensure the reversing trigger line is connected correctly.

Figure 3.3: Rear View Camera Wiring Diagram
Important: Whether you use a rear view camera or not, you must connect the rear view wire. Otherwise, your WiFi and Bluetooth signals may be negatively affected.
4. Operating Instructions
4.1. Machine Host Operations & Controls
| Symbol | Operation & Control |
|---|---|
| MIC | Built-in microphone hole |
| RST | Reset (press with a sharp object) |
| Power Button | Press and hold for 3 seconds to power off; short press repeatedly to mute or unmute |
| Home Icon | Go to main menu |
| Return Icon | Return to the previous interface |
| Volume Up Icon | Press or hold repeatedly to increase volume |
| Volume Down Icon | Press or hold repeatedly to decrease volume |
4.2. On-Screen Main Interface
(Note: The main interface may vary slightly between different product versions.)

Figure 4.1: Main UI Interface and Display
| Icon | Name | Operation |
|---|---|---|
| Main Menu Icon | Main menu | Touch to switch screen to main menu |
| Hide Shortcut Menu Icon | Hide shortcut menu | Touch to hide the shortcut menu button area |
| Backstage Icon | Backstage | Touch to show all programs running in the background |
| Return Icon | Return | Touch to switch screens to return to previous screen |
| Setting Icon | Setting | Touch to enter Settings |
| Application Icon | Application | Touch to enter More App Interface |
4.3. On-Screen Drop-Down List
| Icon | Name | Operation |
|---|---|---|
| Navigation Icon | Navigation | Touch to enter Navigation |
| Wi-Fi Icon | Wi-Fi | Turn on/off Wi-Fi |
| Bluetooth Icon | Bluetooth | Turn on/off Bluetooth |
| Screen Off Icon | Screen off | Open/Close Screen |
| Screenshot Icon | Screenshot | Touch to take a screenshot |
| Car Setting Icon | Car setting | Touch to enter Car setting |
| Clean-up Icon | Clean-up | Touch to clean |
| Video Out Icon | Video out | Touch to set Video out |
| OPTICAL Icon | OPTICAL | Turn on/off OPTICAL |
4.4. On-Screen APP Icons
Some apps may require additional accessories to function. Check product details for optional accessories.
| Icon | Name | Operation |
|---|---|---|
| BT Icon | BT | Touch to enter Bluetooth settings |
| ESSGOO Voice Icon | ESSGOO Voice | Touch to enter smart voice settings |
| ESSGOO+ Icon | ESSGOO + | Touch to enter the intelligent voice software |
| DAB+ Icon | DAB+ | Touch to enter DAB+ functions |
| HERE WeGo Icon | HERE WeGo | Touch to enter offline map |
| Car Set Icon | Car set | Touch to enter car settings |
4.5. Main Functions and Usage
Intelligent Voice - ESSGOO+ (Optional)
Activate by shouting "Hey ESSGOO". The system provides specific voice commands. Log in with your Google or Facebook account to access product introductions, operation videos, and Q&A for troubleshooting.

Figure 4.2: ESSGOO+ Intelligent Voice Interface
Mirror Link - Phonelink
Connect your smartphone to the car stereo using Mirror Link. (Note: Different products may use different apps for Mirror Link.)

Figure 4.3: Mirror Link Connection Steps
- Android USB: Connect your Android phone via USB cable and follow on-screen prompts.
- Android WIFI: Connect your Android phone wirelessly via Wi-Fi and follow on-screen prompts.
- iPhone WIFI: Connect your iPhone wirelessly via Wi-Fi (AirPlay mirror) and follow on-screen prompts.
Offline Map - HERE WeGo
You can use the HERE WeGo app for offline navigation. (Google Maps can also be used online.)
- Power on the device and connect to the internet via Wi-Fi.
- Find the HERE WeGo app in the main menu.
- Follow the app prompts to enter the main map page and find the options menu.
- Click "Use the app offline" and download your preferred map data from the country list.

Figure 4.4: HERE WeGo Offline Map Setup
CarPlay / Android Auto Software Description (Optional)
The unit supports CarPlay and Android Auto for seamless smartphone integration. Connect your phone via wired USB or wireless Bluetooth/Wi-Fi as prompted by the Zlink app.

Figure 4.5: CarPlay / Android Auto Interface
5. Maintenance
To ensure the longevity and optimal performance of your MOPECT car stereo, follow these maintenance guidelines:
- Cleaning: Use a soft, dry cloth to clean the screen and exterior. Avoid abrasive cleaners or solvents.
- Temperature: Avoid exposing the unit to extreme temperatures, both hot and cold, for extended periods.
- Moisture: Keep the device dry and away from liquids.
- Software Updates: Periodically check for software updates from the manufacturer's official website to ensure the best performance and access to new features.
- Professional Service: For any complex issues or internal repairs, always seek assistance from qualified professionals.
6. Troubleshooting
If you encounter issues with your car stereo, refer to the following common problems and solutions:
- No Power: Ensure all power cables (red, yellow, black) are securely connected to the 12V battery. Re-perform the initial test. Check the fuse.
- No Sound/Low Volume: Check speaker connections. Adjust volume settings on the unit and your phone (if connected via Bluetooth/CarPlay/Android Auto). Note that some users have reported the amplification might not be very powerful compared to premium brands.
- Poor Radio Reception: Ensure the radio antenna is securely connected. Check for local signal strength.
- GPS Not Working: Ensure the GPS antenna is properly installed and has a clear view of the sky. Check GPS settings in the unit.
- Mirror Link/CarPlay/Android Auto Connection Issues: Ensure your phone's software is up to date. Try both wired (USB) and wireless (Wi-Fi/Bluetooth) connections. Reinstall the respective apps on your phone if necessary.
- Unit Freezes/Unresponsive: Use a sharp object to press the RST (Reset) button. If issues persist after updating, you may need to enter recovery mode to reset to factory settings (consult support if unsure).
- Overheating/Component Failure: Some users have reported issues with the power amplifier (e.g., TDA7388) overheating due to lack of proper cooling. Ensure adequate ventilation around the unit during installation. If you suspect component failure, contact customer service.
- Compatibility: This is a universal 2 DIN unit. For specific vehicle models (e.g., Mercedes B200, VW Polo, Ford Ka, Suzuki Swift, Mitsubishi Pajero), ensure you have the correct mounting frame and wiring harness adapters.
If you cannot resolve an issue using these steps, please contact customer support for further assistance.
7. Specifications
The following table details the technical specifications of the MOPECT 9-inch 2 DIN Android Car Stereo Multimedia System.
| Category | Parameter |
|---|---|
| System | Android 15 |
| CPU | Cortex A7 1.5GHz (8227L & MT8163) |
| Core | 4 |
| Memory (RAM) | 1G / 2G / 4G (depending on model) |
| Storage (ROM) | 16G / 32G / 64G (depending on model) |
| Display Size | 9 inches |
| Resolution | 1024*600 / 1024*480 / 1280*720 / 768*1024 / 800*1280 (IPS Capacitive Touch Screen) |
| Radio | FM / RDS (87.5M-108M) |
| Bluetooth Version | 4.2 |
| Communication | WIFI |
| Satellite Positioning | GPS (Offline Maps & Online Maps) |
| Amplifier Chip | 7388 |
| Out Power | 45W*4 |
| Voltage | 12 V |
| Sound Decoder | 2133 |
| Mirror Link | Phonelink (TIMA) |
| Special Features | Built-In Speaker/Microphone, WiFi function, Built-in GPS, Voice Control, DSP, CarPlay, Android Auto, Reversing Input, Split Screen, Support steering wheel control |
| Digital Media Format | CD, MP3, FLAC, APE, WMA, WAV, AAC, AMR, AVI, ASF, MP4, MOV, MPGMPEG1/2/4, VOB, MKV, FLV, TS, WMV, RMVB, 3GP |
| Rear Camera Standard | CVBS (Supports AHD 1080P/CVBS) |
| USB Ports | Dual USB (one for CarPlay, one for data/USB input) |
| Optional Accessories Support | External Microphone, Video Output, DVR, OBD2, DAB+, Dash Cam |
| OSD Language | Chinese (Traditional), Arabic, Irish, Estonian, Belarusian, Polish, Danish, German, Russian, French, Filipino, Finnish, Korean, Czech, Croatian, Latin, Romanian, Malay, Portuguese, Swedish, Serbian, Slovenian, Thai, Turkish, Ukrainian, Hebrew, Greek, Spanish, Italian, English, Vietnamese |
| Factory Password | 8888 or 000000 |
Package Contents:

Figure 7.1: Package Contents (4G+64GB Model shown)
- 1 x 2 DIN Car Stereo
- 1 x Bracket & Screws
- 1 x GPS Antenna
- 1 x Universal Power Cable
- 1 x ISO Power Cable
- 1 x RCA Cable
- 1 x Backup Camera Input Cable
- 2 x USB Cables
- 1 x User Manual
- Optional: 1x AHD Rear View Camera, 1x DAB BOX, 1x Dash Camera
8. Warranty and Support
Thank you for choosing our product. If you have any further questions or require assistance, please contact our customer service team. The user interface and functions of the product may be updated without prior notice, and minor differences from this manual are considered normal.
EU Declaration of Conformity:
This device complies with the essential requirements and other relevant provisions of Directive 2014/30/EU and Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at https://essgoo.com/pages/doc.
Manufacturer/Exporter Information:
- Manufacturer/Exporter: Shen Zhen Xin Sheng Shang Technology Co.,LTD.
- Production Site: Room 303, Building 9, No. 54-6, Guanlan Avenue, Xinhe Community, Fucheng Street, Longhua District, Shenzhen City, Guangdong Province, China 518000
- Phone: +86 13048907387
- E-mail: support@essgoo.com
- Official Website: www.essgoo.com
9. User Tips
Based on feedback from other users, here are some helpful tips for your MOPECT car stereo:
- Quick Connectivity: The unit connects quickly with both Android and iPhone devices. Wireless Android Auto is reported to work very well.
- Customization: Take advantage of the ability to set up steering wheel controls for convenience. If your vehicle has a CANBUS system, it can often be configured with this unit.
- Navigation: The built-in navigation is generally good. Remember you can download offline maps with HERE WeGo or use online maps via Wi-Fi.
- Audio Performance: While the unit offers many features, some users note that the amplification might not be as powerful as high-end branded radios. Adjust your expectations accordingly.
- Cooling Consideration: A critical observation from users is the potential for the power amplifier (e.g., TDA7388) to overheat due to a lack of dedicated cooling, especially with a plastic back casing. During installation, ensure there is sufficient ventilation around the unit to prevent overheating and potential component failure.