LHY AUDIO Dual PCM1794A

Contents

LHY AUDIO Dual PCM1794A DAC Audio Decoder Board User Manual

Model: Dual PCM1794A

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your LHY AUDIO Dual PCM1794A DAC Audio Decoder Board. This high-fidelity audio board features dual PCM1794A decoding chips, 5532dd+5534dd operational amplifiers, and supports 24-bit 192KHz audio processing with XLR and RCA outputs, and I2S input.

2. Product Features

  • Dual PCM1794A decoding chips for high-quality audio conversion.
  • Equipped with 5532dd and 5534dd operational amplifiers.
  • Supports I2S digital audio input.
  • Provides both XLR balanced output and RCA single-ended output.
  • Supports sampling rates up to 24Bit/192KHz.
  • Integrated 4 low-noise voltage regulator chips for stable power.

3. Specifications

ParameterValue
Model NumberDual PCM1794A
Digital Power Supply5V DC
Analog Power Supply±12V DC
Input TypeI2S
PCM Word Length24-bit
PCM Sampling Frequencies192 kHz
Output TypeBalanced (XLR), Single-ended (RCA)
RCA Output Amplitude2RMS
Balanced Output Amplitude4RMS
Board Dimensions (LxWxH)104mm x 82mm x 1.6mm
MaterialPlastic (PCB)
DIY Supplies CategoryElectrical

4. Setup and Connections

Careful attention to power supply and signal connections is crucial for optimal performance and to prevent damage.

4.1 Board Overview

Top view of the LHY AUDIO Dual PCM1794A DAC board with XLR and RCA connectors.
Figure 1: LHY AUDIO Dual PCM1794A DAC Board (Assembled)

This image shows the fully assembled DAC board, highlighting the XLR and RCA output connectors, and the general layout of components including op-amps and capacitors.

4.2 Connection Diagram

Annotated diagram of the DAC board showing I2S input, DC power supply, XLR balanced output, RCA output, and internal components like dual 1794 decoding chip and low noise voltage regulators.
Figure 2: DAC Board Connection Points and Key Components

Refer to Figure 2 for a visual guide to the board's connection points:

  • I2S Input: Located on the left side of the board. This is where your digital audio source (e.g., a digital audio player or streamer) connects. The pinout is typically GND, NCK, LRCK, DATA.
  • DC Power Supply: Requires both +12V, -12V, and +5V DC. Ensure correct polarity and voltage to prevent damage. The board includes 4 low-noise voltage regulator chips for stable operation.
  • XLR Balanced Output: Provides a balanced audio signal, typically used for professional audio equipment.
  • RCA Single-ended Output: Provides a standard single-ended audio signal, commonly used with consumer audio equipment.
  • Op-Amps: The board features 6 single op-amps and 4 dual op-amps for I/V conversion and output buffering.

4.3 PCB Layout and Dimensions

Technical drawing of the DAC board PCB layout with dimensions in centimeters and pin labels for I2S input and DC input.
Figure 3: PCB Layout with Dimensions and Pinouts

Figure 3 provides detailed dimensions of the PCB (104mm x 82mm x 1.6mm) and pin assignments for I2S input and DC power input. This is essential for custom enclosures or integration into existing systems.

Front view dimension diagram of the DAC board, showing connector heights and spacing.
Figure 4: Front View Dimensions

Figure 4 illustrates the front view dimensions, including connector heights and spacing, which is useful for panel mounting and enclosure design.

4.4 Installation Steps

  1. Prepare Power Supply: Ensure you have a stable DC power supply providing +5V, +12V, and -12V.
  2. Connect Power: Carefully connect the power supply to the DC Input terminals on the board, observing correct polarity. Incorrect voltage or polarity can damage the board.
  3. Connect I2S Input: Connect your digital audio source's I2S output to the I2S Input pins on the DAC board. Match GND, NCK, LRCK, and DATA pins correctly.
  4. Connect Audio Output:
    • For balanced audio, connect XLR cables from the DAC's XLR outputs to your amplifier or active speakers.
    • For single-ended audio, connect RCA cables from the DAC's RCA outputs to your amplifier or receiver.
  5. Verify Connections: Double-check all connections before applying power to the system.

5. Operation

Once all connections are securely made and verified:

  1. Power on your audio source (e.g., I2S player).
  2. Power on the LHY AUDIO DAC board.
  3. Power on your amplifier or active speakers.
  4. Start playing audio from your source. The DAC board will convert the I2S digital signal into an analog signal for your audio system.

No further user interaction is typically required with the DAC board itself during operation, as it functions as a signal converter.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to gently clean the board. Avoid using liquids or abrasive cleaners.
  • Environment: Keep the board in a dry, dust-free environment. Avoid extreme temperatures and humidity.
  • Static Electricity: Handle the board with care, especially when installing or removing, to avoid damage from static discharge. Use anti-static precautions if possible.
  • Ventilation: Ensure adequate ventilation if the board is enclosed to prevent overheating.

7. Troubleshooting

ProblemPossible CauseSolution
No sound output
  • Incorrect power supply connection.
  • Incorrect I2S input connection.
  • Incorrect audio output connection.
  • Audio source not playing or improperly configured.
  • Amplifier/speakers not powered on or muted.
  • Verify all power supply voltages and polarity.
  • Check I2S pin assignments (GND, NCK, LRCK, DATA).
  • Ensure RCA/XLR cables are securely connected to the correct inputs on your amplifier.
  • Confirm audio source is active and outputting I2S.
  • Check amplifier/speaker power and volume.
Distorted or noisy sound
  • Ground loop issues.
  • Poor quality power supply.
  • Interference from other electronic devices.
  • Damaged cables.
  • Ensure proper grounding for all audio components.
  • Use a high-quality, stable power supply.
  • Keep the DAC board away from sources of electromagnetic interference.
  • Try different audio cables.
Board not powering on
  • No power to the DC input.
  • Incorrect power supply voltage or polarity.
  • Faulty power supply unit.
  • Check power source and connections.
  • Verify power supply output with a multimeter.
  • Try a different power supply if available.

8. User Tips

  • Power Supply Quality: The performance of any DAC is highly dependent on the quality of its power supply. Consider using a linear power supply for optimal audio performance.
  • I2S Signal Integrity: Use short, high-quality cables for I2S connections to minimize signal degradation and noise.
  • Grounding: Proper grounding of your entire audio system can significantly reduce hum and noise.

9. Warranty and Support

For any issues not covered in this manual, or for warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.

© 2023 LHY AUDIO. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.