Wishcolor ATS25 ULTRA

Contents

Wishcolor ATS25 ULTRA SDR Receiver User Manual

Model: ATS25 ULTRA

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your Wishcolor ATS25 ULTRA FM SW SSB MW LW AIR SDR Receiver. Please read this manual thoroughly before using the device to ensure optimal performance and longevity.

1.1 Product Overview

The HamGeek ATS25 ULTRA is an advanced Software Defined Radio (SDR) receiver, building upon the ATS25PRO+ model. It features a 4-inch touch screen, optimized performance, and a compact handheld design. It supports a wide range of frequency bands and demodulation modes, making it a versatile tool for radio enthusiasts.

1.2 Key Features

  • Built-in WiFi antenna, with the detector located on the side of the body, eliminating the need for bulky external antennas.
  • Electronic button ignition (no need to use the easily worn and replaceable mini switch like the old ATS25).
  • Equipped with a 4-inch display screen, which improves clarity and readability for screen control and is practical for decoding digital signals.
  • Equipped with a 5000mAH battery (built-in charging circuit), designed to supply power to all high-current functions, preventing receiver overload, especially when decoding SSTV and Wefax images at high volume.
  • The front of the body features high-quality speakers, providing excellent audio playback. Technical and structural measures minimize interference and RF noise from inter-chip I2C communication and data transmission with displays.
  • Precaution: The firmware has been activated because the license and activation key have been inserted (so you do not need to purchase the cipher).
  • Wide frequency coverage: LW, MW, SW (0-30MHz high frequency, divided into amateur radio frequency band and broadcast frequency band, all continuously covered); Commercial FM band from 65 to 108MHz.
  • VHF band (30.001 to 280.000MHz) distinguishes between amateur radio band, aviation band, maritime band, 6-meter band, and 2-meter band, and can continuously cover the entire frequency range.
  • All receiving frequency bands can be demodulated, including AM, USB, LSB, CW, FM, NFM, and DIGI modes (CW to left, RTTY to left 45/50/75 baud, FT8/FT4, FELDHELL, PSK31/63, SSTV, WEFAX567-288, etc., 120-240 lines).
  • Equipped with a low-noise amplifier (LNA) that can be activated as needed, with extremely high efficiency.
  • Equipped with a Bluetooth circuit that can be used in conjunction with an external amplifier system and can be activated as needed.

2. Specifications

FeatureSpecification
Model NumberATS25 ULTRA
Brand NameWishcolor (TZT)
TypeFM, MW, SW, LW, SSB, Air Band SDR Receiver
Screen4-inch Touch Screen
Body MaterialMetal
Power SupplyRechargeable Battery Pack (5000mAH)
Battery IncludedYes
ConnectivityBluetooth, WiFi
FM Frequency64MHz - 108MHz (with RDS function)
LW Frequency153kHz - 500kHz
MW Frequency520kHz - 1710kHz
SW Frequency1730kHz - 30000kHz
SSB Frequency1730kHz - 30000kHz
Air Band Frequency118MHz - 138MHz (AM)
VHF Frequency118MHz - 214MHz
Demodulation ModesAM, USB, LSB, CW, FM, NFM, DIGI
Package Weight0.512 kg
Package Dimensions10 x 10 x 6 cm

3. Setup

3.1 Initial Power-On

The device features an electronic button ignition. Press the power button to turn on the receiver. The firmware is pre-activated, so no license key input is required.

3.2 Connecting Peripherals

  • Bluetooth: To connect wireless audio devices, navigate to the BT/Wi-Fi settings. Enable Bluetooth to pair with external amplifiers or headphones.
  • Wi-Fi: The device has a built-in Wi-Fi antenna. To connect to a network, go to BT/Wi-Fi settings, enable Wi-Fi, and select an access point from the list. You may need to enter a password for the first connection. The Wi-Fi connection is essential for accurate time setting for FT4/FT8 decoding and for firmware updates.
  • Antenna: The receiver comes with a telescopic antenna. Connect it to the appropriate port for optimal reception. The LNA (Low-Noise Amplifier) can be activated as needed for improved signal reception.

3.3 Screen Calibration

If the touch screen responsiveness is inaccurate, you can recalibrate it:

  1. With the device turned off, press and hold the screen.
  2. Turn on the power.
  3. Continue holding the screen until a message indicates that screen calibration has started.
  4. Follow the on-screen prompts, tapping the indicated positions one by one. Calibration is complete.

3.4 Device Component Configuration

For correct functioning, select the appropriate device model. If your device has been modified or assembled by yourself, choose "Generic" and then select the components installed in your receiver. Available components for configuration include:

  • Battery charge level indication
  • Battery charging process indication
  • Additional Lock button (for ATS120 and ATS200 series)
  • Bluetooth module
  • Morse code and digital communications decoder
  • HF preamplifier
  • 50 Ohm / Hi-Z antenna impedance switching circuit
  • HF range filters (various models)
  • Special mixer for ATS200 series aviation band receivers
  • Non-standard mixer connection for converter ranges to pin CLK O of the SI5351 generator

4. Operation

4.1 Main Screen Overview

The ATS25 ULTRA features a 4-inch touch screen for intuitive control. The main screen displays various indicators and controls depending on the selected mode (FM or SSB).

ATS25 Ultra SDR Receiver main screen with antenna extended, showing frequency 104.30 MHz, RSSI, SNR, and control buttons.
Figure 4.1: ATS25 ULTRA Main Screen (FM Band Example)

Indicators and Panel (Quick Start):

  • S-meter: Displays signal strength (RSSI) and signal-to-noise ratio (SNR). Press to switch between histogram or waterfall mode. Press and hold to toggle metering on/off.
  • Volume: Press to turn sound on/off.
  • SQ (Squelch): Indicates active squelch.
  • MF: Simultaneous function indicator for listening to multiple frequencies.
  • Indicator Panel: Displays active circuit elements. Click to show control buttons.
  • Wi-Fi Connection: Tap to toggle on/off. Color indicates status: green (active), orange (no internet), red (error), gray (no networks).
  • Battery Charge Level: Tap to display percentage or volts. "Lightning" icon indicates charging. Color changes (yellow/red) as charge decreases.

Status Panel:

  • TUNE/BFO: Used for fine-tuning frequency.
  • GAIN/AGC: Automatic gain control or attenuator.
  • FILTER/BANDW: LF bandwidth.
  • STEP: Setup step.
  • BAND/MODE: Range and modulation.

4.2 Adjusting Volume and Signal Gain

4.2.1 Volume Control

  • To adjust volume, press the VOL button or rotate the encoder.
  • To mute, press the MUTE button or the volume indicator.
  • Squelch automatically mutes sound when no station signal is present. Adjust squelch level by pressing VOL in volume control mode or rotating the encoder. Squelch is not available for SSB mode.

4.2.2 Auto Gain Control (AGC) and Attenuator (ATT)

  • Press the ATT button to enter attenuator adjustment mode. Rotate the encoder to set the attenuator level to prevent RF input overload. Higher values mean weaker signal amplification. Press ATT again to exit.
  • Press the AGC button to enable automatic signal gain. The status bar will show the AGC indicator. Press AGC again to set maximum level gain.

4.3 Frequency Tuning

4.3.1 Direct Frequency Entry

Press the FREQ button on the main screen to enter frequency input mode. Use the on-screen number buttons to enter the desired frequency. The unit (MHz/kHz) will be selected automatically. Use the "dot" for FM broadcast frequencies. Use the "←" button to delete incorrect numbers. Press OK to set the frequency. Press CANCEL to exit without changes. Press SCAN to enter multi-frequency simultaneous listening mode (not available for SSB).

4.3.2 BFO Generator (SSB Fine Tuning)

For fine-tuning in SSB mode, use the BFO generator. Enter oscillator trim mode by pressing the BFO button or long-pressing the encoder. The adjustment frequency ranges from -1999 to +1999 Hz. The adjustment step can be changed via the STEP button. To reset BFO or SI5351 frequency to default, long-press the frequency display.

4.4 Band Selection and Modulation

The receiver supports various frequency bands and modulation types.

4.4.1 Amateur Radio Bands (HAM)

Press the HAM button to access amateur radio frequency ranges. The list displays frequency ranges and their corresponding wave passages (red: bad, yellow: average, green: good).

ATS25 Ultra showing HAM radio band selection screen with various frequency ranges and signal quality indicators.
Figure 4.4.1: HAM Radio Band Selection

4.4.2 Broadcast Bands (BAND)

Press the BAND button to access broadcast frequency ranges.

4.4.3 FM Channel Mode

Press the FM button on the main screen to enter FM channel mode. This displays station name, frequency, RDS info, stereo indicator, and time. Rotate the encoder or use PROG+/PROG- to switch channels. STEREO button toggles stereo reception. RDS button toggles RDS information. Press FM again to exit.

4.4.4 CB Channel Mode

Press the CB button to listen to civil band channels. This mode displays channel number, grid designation, frequency, modulation, and time. Rotate the encoder to switch channels. Use GRID+/GRID- to switch grids. AM, NFM, LSB, USB buttons select modulation. The EU button toggles the European frequency grid. Press CB again to exit.

4.4.5 Modulation, Bandwidth, and Tuning Step

Use the MODE, BANDW, or STEP buttons on the main screen to select modulation, bandwidth, or tuning step respectively. The current settings are displayed. Grayed-out buttons indicate unavailable options.

4.4.6 Types of Modulation / Digital Decoders

The receiver supports various modulation types and digital decoders for amateur radio and HF bands.

  • CWR / CW: Enable Morse code decoder.
  • DIGI: Opens a list of digital communication decoders (RTTY, FT8/FT4, FELDHELL, PSK31/63, SSTV, WEFAX).

4.5 Memory Functions

4.5.1 Station Memory List

Save current frequency, modulation type, and range to memory. Rotate the encoder to browse saved cells. Press ADD to save current settings. Press EDIT to modify, DEL to delete. When saving, enter station name using the on-screen keyboard and select city location (THIS: current city, ALL: any city, NONE: no connection). The list display filter can be set in the SETUP -> MEMORY LIST section.

4.5.2 List of Locations (Cities)

Add your location to the cities memory for correct time display and station distribution. Similar to stations, cities can be added, changed, and deleted. After editing, rotate the encoder to select the time zone. Press SCAN to search and save FM stations for the city. Use the FM button to go to the list of saved FM stations for the city.

ATS25 Ultra showing city and station memory list, with options to edit, add, delete, and scan.
Figure 4.5.2: City and Station Memory Management

4.6 Range Scanner

The range scanner allows you to search for signals within a specified frequency range.

  • Rotate the encoder to move the cursor or select a location on the display.
  • The screen displays initial and final scanning frequencies, and marks of found signals.
  • The signal graph shows RSSI and SNR.
  • FREQ: Horizontal scale control.
  • RSSI: Vertical scale control.
  • SNR: Graphics contrast control.
  • PAUSE: Stops scanning and listens to the broadcast.
  • STEP: Selects encoder setting step.

4.7 Retro Receiver Scale

Press the RETRO button to display the retro scale, showing stations from selected bands and cities stored in memory. Navigate by rotating the encoder or sliding the touch screen. Swipe to advance to the next station. The screen displays current frequency, band, city, time, and battery charge. A retro S-meter is located separately (press to switch to spectrum indicator and back).

4.8 Virtual Encoder

The virtual encoder can be accessed by sliding upward from the bottom edge of the screen. It duplicates the actions of the physical encoder. Slide in the opposite direction to close it. It closes automatically after inactivity. Press and hold arrow buttons to simulate rotation.

5. Digital Decoders

5.1 Morse Code Decoder

To decode Morse code, align the red mark on the "waterfall" display with the signal and adjust the volume (around 45) until the signal is clearly visible. The yellow indicator will flash in time with the signal, and decoded characters/words will appear. The Cyrillic alphabet can be used for the alphabet decoder.

5.2 RTTY, PSK, and Feld-Hell Decoders

Align the red mark on the "waterfall" with the signal and adjust volume. For RTTY L/U, use the left/right signal stream. Scroll the screen and rotate the encoder to manually scroll. The SET button for RTTY adjusts baud rate (45.45/50/75). For Feld-Hell, toggle anti-aliasing. For PSK, switch between BPSK31/BPSK63. For FT4/FT8, set time manually (see 5.3). Received Feld-Hell transmissions will be smoothed for easier reading.

5.3 FT4/FT8 Decoder

Accurate time setting is crucial for FT4/FT8 decoding. Connect the receiver to Wi-Fi for automatic time synchronization or set it manually. The UTC TIME line displays the current time. For each FT4/FT8 gear, power, signal, offset, and transmission data are displayed.

6. Maintenance and Energy Saving

6.1 File Handling

To manage files (upload, download, delete) in the receiver's memory, use the A-explorer application on a PC. Files include:

  • city.csv: List of locations (ID, name, time zone).
  • preset.csv: List of saved stations (frequency, name, city ID, modulation).
  • label.csv: List of frequency boundaries.
  • decoder.log: Decoder log file (erased when the decoder starts).
  • scan.csv: Frequency lists for simultaneous listening.
  • ap.csv: List of saved Wi-Fi access points.
  • setting.ini: Override settings.
  • *.lng: Interface localization files.
  • value.hex: Dump of saved settings.
  • flag.ini: Data for country flag in RDS info.

6.2 Energy Saving Tips

To extend battery life:

  • Enable screen saver and display backlight turn-off after inactivity in settings.
  • Reduce screen backlight brightness using the LIGHT button and encoder.
  • Turn off Wi-Fi and Bluetooth when not in use.
  • Use wired headphones instead of Bluetooth to reduce power consumption.

7. Troubleshooting

7.1 Common Issues

  • No Wi-Fi connection: Check Wi-Fi antenna connection. Ensure the access point is within range.
  • Inaccurate touch screen: Perform screen calibration (see Section 3.3).
  • Digital decoder issues: Ensure correct frequency alignment on the waterfall display and proper volume levels. For FT4/FT8, verify time synchronization.
  • Device unresponsive: Try a factory reset (see Section 7.2).
  • Warning about unacceptable battery level: A message will be displayed if the battery is charged to levels that exceed acceptable limits.

7.2 Factory Reset

To restore all settings to their default values:

  1. Turn off the device.
  2. Press and hold the encoder button.
  3. Turn on the power.
  4. Release the encoder button when "LOADED DEFAULTS" appears.

After a factory reset, you will need to perform the initial setup and configure main parameters again.

8. User Tips

  • 11m Band FM Modulation: According to user queries, it is possible to set FM modulation in the 11m band.
  • Optimal Digital Decoding: For best results with digital modes like RTTY or FT8, ensure your device's time is synchronized via Wi-Fi and carefully align the signal on the waterfall display.
  • Battery Management: Utilize the energy-saving features (screen saver, backlight dimming, turning off unused wireless functions) to maximize operating time, especially during extended listening sessions.

9. Warranty and Support

For detailed information regarding warranty, technical support, and additional documentation, please refer to the official user manual PDF available at: User Manual (PDF). This PDF contains comprehensive guides and documents for your ATS25 ULTRA receiver.

Information about firmware updates, licensing, and device details can also be found in the device's INFO section (accessible via the INFO button on the main screen).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.