Flipsky FSESC 110300

Contents

Flipsky FSESC 110300 High Voltage ESC User Manual

Electronic Speed Controller for High-Performance Applications

1. Product Overview

The Flipsky FSESC 110300 is a high-voltage, high-current Electronic Speed Controller (ESC) designed for demanding applications such as fighting robots, surfboards, AGV robots, and electric scooters. It is based on the VESC platform, offering advanced control modes and robust protection features. This manual provides essential information for the safe and effective use of your FSESC 110300.

Flipsky FSESC 110300 High Voltage ESC front view

Figure 1: Front view of the Flipsky FSESC 110300 High Voltage ESC.

2. Specifications

FeatureDetail
Firmware6.05 (or above)
Voltage Range14-110V (safe for 4-26S battery configurations)
Continuous Current110V/300A (dependent on mounting, ambient temperature, and air/water circulation)
Burst Current800A
BEC Output5V@3A
Supported ModesBLDC, FOC (sinusoidal)
ERPM150000
Communication PortsUSB, CAN, UART, SPI, IIC
Supported SensorsABI, HALL, AS5047, AS5048A
Input Source SupportPPM, ADC, NRF, UART
Sensorless OperationYes
Regenerative CapacityYes
ProgrammabilityVia VESC_TOOL
Dimensions (L*W*H)183.8mm * 80.2mm * 43.8mm
Motor/Power Wire Size8AWG
Phase FilterYes
Power Switch ButtonRed
CPUSMT32F405 with 168MHz frequency
PCB DesignAluminum PCB for enhanced heat dissipation
Dimensions of Flipsky FSESC 110300 High Voltage ESC

Figure 2: Physical dimensions of the FSESC 110300.

3. Setup and Wiring

Proper setup and wiring are crucial for the safe and optimal performance of your FSESC 110300. Refer to the wiring diagram below for connection details.

Wiring diagram for Flipsky FSESC 110300 High Voltage ESC

Figure 3: Detailed wiring diagram for the FSESC 110300.

3.1 Connection Points:

  • Battery Connection: Connect your high-voltage battery pack to the main power input (red for positive, black for negative).
  • Motor Connection: Connect the three motor phase wires (yellow, blue, green) to the corresponding outputs.
  • 1. Power Switch: For controlling the power to the ESC.
  • 2. CAN: Controller Area Network for communication with other devices.
  • 3. PPM: Pulse Position Modulation for traditional RC receiver input.
  • 4. USB: For connecting to a computer for configuration via VESC_TOOL.
  • 5. SWD: Serial Wire Debug for advanced debugging.
  • 6. UART2: Universal Asynchronous Receiver-Transmitter for serial communication.
  • 7. COMM: General communication port.
  • 8. HALL: For Hall effect sensor input from the motor.
  • LED Indicator: Provides status feedback.

3.2 Initial Setup:

  1. Ensure all connections are secure and correctly polarized. Incorrect wiring can damage the ESC and connected components.
  2. Connect the ESC to a computer via the USB port.
  3. Launch the VESC_TOOL software.
  4. Follow the VESC_TOOL wizard for motor detection and initial configuration. This includes setting motor parameters, battery voltage limits, and control modes.
  5. Perform a throttle calibration if using PPM input.
  6. Test the motor direction and response at low power before full operation.

4. Operating Instructions

The FSESC 110300 supports various control modes, including Current, Duty Cycle, Speed, and PID control. These modes are configured via the VESC_TOOL software.

4.1 Control Modes:

  • Current Control: Directly controls the motor current, providing precise torque control.
  • Duty Cycle Control: Controls the percentage of time the motor is powered, suitable for basic speed control.
  • Speed Control (RPM): Maintains a target motor RPM, useful for applications requiring constant speed.
  • PID Control: Advanced control loop for precise regulation of speed or position.

Select the appropriate control mode in VESC_TOOL based on your application requirements. Always ensure your settings are safe for your motor and battery combination.

4.2 Protection Features:

The ESC is equipped with adjustable protection features to safeguard itself and connected components:

  • Low Voltage Protection
  • High Voltage Protection
  • Over Current Protection
  • Temperature Abnormal Protection (MOSFETs / Motor)

These protections can be configured within VESC_TOOL to match your battery and motor specifications. It is highly recommended to set these limits correctly to prevent damage.

5. Maintenance

To ensure the longevity and reliable performance of your FSESC 110300, follow these maintenance guidelines:

  • Keep Clean: Regularly inspect the ESC for dust, dirt, or debris. Clean with a soft brush or compressed air. Avoid using liquids directly on the board.
  • Ensure Airflow: The aluminum PCB design aids in heat dissipation. Ensure adequate airflow around the ESC, especially during high-current operation. Do not obstruct cooling fins.
  • Check Connections: Periodically check all wiring connections for looseness or corrosion. Secure any loose connections.
  • Firmware Updates: Keep the firmware updated to the latest stable version using VESC_TOOL to benefit from performance improvements and bug fixes.
  • Environmental Conditions: Avoid operating the ESC in excessively humid, dusty, or corrosive environments.

6. Troubleshooting

If you encounter issues with your FSESC 110300, consider the following common troubleshooting steps:

  • No Power/No Response:
    • Check battery connections and ensure the battery is charged.
    • Verify the power switch is in the ON position.
    • Inspect all wiring for breaks or incorrect connections.
  • Motor Not Spinning/Erratic Behavior:
    • Re-run motor detection in VESC_TOOL.
    • Check motor phase wire connections.
    • Verify Hall sensor connections if using sensored mode.
    • Ensure the control input (PPM, UART, etc.) is correctly configured and receiving signals.
  • Overheating:
    • Check for adequate ventilation and airflow around the ESC.
    • Ensure the motor is not overloaded or experiencing excessive resistance.
    • Review current limits and temperature cutoffs in VESC_TOOL.
  • ESC Shuts Down Unexpectedly:
    • This could be due to protection features triggering (low/high voltage, overcurrent, over-temperature). Check VESC_TOOL logs for fault codes.
    • Verify battery voltage is within the safe operating range (14-110V).
    • Ensure current draw does not exceed continuous or burst limits.
  • Communication Issues (USB/UART/CAN):
    • Ensure correct drivers are installed for USB.
    • Verify baud rates and connection settings in VESC_TOOL for UART/CAN.
    • Check physical connections for continuity.

If issues persist after basic troubleshooting, consult the VESC community forums or contact Flipsky support.

7. User Tips

  • Check Package Contents: Upon receiving your FSESC 110300, verify that all expected cables and accessories are included before starting installation.
  • VESC_TOOL is Your Friend: Familiarize yourself with the VESC_TOOL software. It is essential for configuration, monitoring, and diagnostics. Regular use will help you optimize performance and troubleshoot effectively.
  • Start Conservatively: When setting up new motor/battery combinations, begin with conservative current limits and gradually increase them as you gain confidence in the system's stability.
  • Heat Management: While the aluminum PCB provides good heat dissipation, always ensure your enclosure and mounting allow for sufficient airflow, especially in high-power applications.

8. Warranty and Support

Flipsky provides a warranty for its products. Please review the following terms:

8.1 Warranty Period:

  • Consumable Electronic Products (e.g., VESC, Motor, Battery): 2 months from the 7th day after shipment (date checked by logistic record).
  • Non-Electronic Products: 2 months from the 7th day after shipment (date checked by logistic record).
  • Group-Buy Products: 1 month from the 7th day after shipment.

The warranty policy was updated on November 1, 2018. Products purchased before this date follow the previous policy.

8.2 Conditions Not Covered by Warranty:

  • Lack of purchase channel source proof.
  • Mechanical damage to electronic components or PCB.
  • PCB board has repair soldering iron traces (excluding solderable cable bullet connectors).
  • Water damage or external impact damage.
  • Abnormal applications beyond the product specifications.
  • Products purchased from channels other than Flipsky.
  • Wear and tear caused by normal use is not considered a defect.

Flipsky tests all VESC and motors 100% before shipment to ensure quality.

8.3 Repair Service:

Flipsky offers repair services for a reasonable charge if your product is out of warranty. Shipping costs for repair services (both ways) are the responsibility of the customer.

8.4 Contact Support:

For warranty claims, technical support, or any questions regarding installation and VESC/Motor settings, please contact Flipsky service at: flipsky_service@outlook.com. It is recommended to contact support before attempting installation if you have any uncertainties.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.