Flipsky FSESC 110200

Contents

Flipsky FSESC 110200 High Voltage Electronic Speed Controller User Manual

Model: FSESC 110200

Brand: Flipsky

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of the Flipsky FSESC 110200 High Voltage Electronic Speed Controller (ESC). The FSESC 110200 is a high-performance ESC based on VESC technology, designed for applications requiring high voltage and current, such as fighting robots, electric surfboards, AGV robots, and electric scooters.

It features an Aluminum PCB for enhanced heat dissipation and supports various control modes and protection features to ensure reliable operation.

2. Specifications

Feature Specification
Firmware 6.05 (or above)
Voltage 14-110V (safe for 4-26S battery configurations)
Continuous Current 200A (dependent on mounting, ambient temperature, and cooling)
Burst Current 400A
BEC Output 5V@3A
Supported Modes BLDC, FOC (sinusoidal)
ERPM 150000
Communication Ports USB, CAN, UART, SPI, IIC
Supported Sensors ABI, HALL, AS5047, AS5048A
Input Source Support PPM, ADC, NRF, UART
Sensorless Operation Yes
Regenerative Capacity Yes
Programmable Via VESC_TOOL
Dimensions (L*W*H) 144.70mm * 72.80mm * 40.60mm
Motor/Power Wire Size 8AWG
Phase Filter Yes
Power Switch Button Red
CPU SMT32F405 with 168MHz frequency
PCB Type Aluminum PCB for good heat dissipation
Dimensions of Flipsky FSESC 110200
Figure 1: Dimensions of the FSESC 110200. Length: 144.7mm, Width: 72.8mm, Height: 40.6mm.

3. Safety Precautions

  • Always disconnect power before making any connections or disconnections.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Operate the ESC within its specified voltage and current limits.
  • Avoid exposing the ESC to water or excessive moisture unless specifically designed for waterproof applications.
  • Mount the ESC in a location with adequate airflow to ensure proper heat dissipation.
  • High voltage systems can be dangerous. Exercise extreme caution and wear appropriate safety gear.
  • Do not attempt to modify the ESC hardware unless you are a qualified professional.

4. Setup and Installation

The Flipsky FSESC 110200 is designed for easy integration into various systems. Follow these steps for proper setup:

4.1. Component Identification

Wiring diagram for Flipsky FSESC 110200
Figure 2: Wiring Diagram of the FSESC 110200. This diagram illustrates the various connection points including UART2, COMM, PPM, HALL, SWD, USB, CAN, and Power Switch.

Refer to Figure 2 for the location of the following ports:

  • 1. UART2: TX2, RX2, GND, 3.3V
  • 2. COMM: ADC1, ADC2, TX/SCL, RX/SDA, ADC, GND, 3.3V, 5V
  • 3. PPM: SERVO, 5V, GND
  • 4. HALL: 5V, TEMP, HALL1, HALL2, HALL3, GND
  • 5. SWD: CLK, DIO, GND
  • 6. USB: For connecting to VESC_TOOL
  • 7. CAN: CANH, CANL
  • 8. Power Switch: LED+, LED-, COM, NC, LED-
  • Battery Connection: Red (Positive), Black (Negative)
  • Motor Connection: Three phase wires (Blue, Green, Yellow)

4.2. Wiring Instructions

  1. Battery Connection: Connect your battery pack (4-26S, 14-110V) to the main power leads of the ESC. Ensure correct polarity: Red to positive (+), Black to negative (-).
  2. Motor Connection: Connect the three phase wires from your motor to the corresponding output wires of the ESC (Blue, Green, Yellow). The order may affect motor direction; this can be adjusted in VESC_TOOL.
  3. Control Input:
    • PPM (Pulse Position Modulation): For standard RC receivers, connect the signal wire to the SERVO pin, and power (5V, GND) as needed.
    • UART (Universal Asynchronous Receiver/Transmitter): For serial communication with microcontrollers or other devices, connect TX/RX lines to the UART port.
    • CAN (Controller Area Network): For multi-ESC setups or CAN-enabled devices, connect CANH and CANL.
  4. Sensor Connections (Optional): If using sensored motors, connect the Hall sensors (HALL1, HALL2, HALL3), temperature sensor (TEMP), and power (5V, GND) to the HALL port.
  5. Power Switch: Connect the provided power switch to the designated Power Switch port. This allows for convenient power on/off functionality.
  6. USB Connection: Use the USB port to connect the ESC to a computer for configuration and firmware updates via VESC_TOOL.

Important: Double-check all connections before applying power to prevent damage to the ESC or other components.

5. Operation

5.1. Initial Configuration with VESC_TOOL

The FSESC 110200 is programmable via VESC_TOOL. It is highly recommended to perform initial setup and motor detection using this software.

  1. Download and install the latest version of VESC_TOOL from the official VESC project website or Flipsky's support page.
  2. Connect the ESC to your computer via a USB cable.
  3. Launch VESC_TOOL and connect to the ESC.
  4. Follow the motor setup wizard to perform motor detection, calibrate input devices (PPM, UART), and configure protection settings (voltage limits, current limits, temperature limits).
  5. Save your configuration to the ESC.

5.2. Control Modes

The ESC supports various control modes, configurable in VESC_TOOL:

  • Current Control: Directly controls the motor current.
  • Duty Cycle Control: Controls the motor speed by varying the PWM duty cycle.
  • Speed Control (RPM): Maintains a target motor RPM.
  • PID Control: Advanced control for precise speed or position control.

5.3. Protection Features

The FSESC 110200 includes adjustable protection features to safeguard the ESC and motor:

  • Low Voltage Protection
  • High Voltage Protection
  • Over Current Protection
  • Temperature Abnormal Protection
  • MOSFETs / Motor Over Temperature Protection

These protections can be configured within VESC_TOOL to match your specific application and components.

6. Maintenance

  • Regular Inspection: Periodically check all wiring connections for looseness or damage.
  • Cleaning: Keep the ESC free from dust, dirt, and debris. Use compressed air or a soft brush for cleaning.
  • Heat Management: Ensure the ESC's aluminum PCB and heatsink fins are not obstructed to allow for optimal heat dissipation.
  • Firmware Updates: Check the Flipsky website or VESC project for new firmware versions. Updating firmware can provide performance improvements and bug fixes. Always follow the update instructions carefully.
  • Storage: When not in use for extended periods, store the ESC in a dry, cool environment.

7. Troubleshooting

Problem Possible Cause Solution
ESC does not power on No power from battery; incorrect battery connection; faulty power switch. Check battery voltage; verify battery polarity; test power switch functionality.
Motor not spinning or erratic behavior Incorrect motor wiring; motor detection failed; incorrect control input settings; sensor issues. Verify motor phase wire connections; re-run motor detection in VESC_TOOL; check PPM/UART/CAN settings; inspect sensor connections if applicable.
ESC overheating Insufficient cooling; excessive current draw; incorrect motor parameters. Improve airflow/cooling; reduce load; re-check motor detection and current limits in VESC_TOOL.
ESC disconnects from VESC_TOOL Loose USB connection; driver issues; firmware corruption. Ensure USB cable is secure; reinstall VESC_TOOL drivers; attempt firmware re-flash (use caution).
Unexpected shutdowns Protection features triggered (low/high voltage, overcurrent, overtemperature). Check VESC_TOOL fault codes; review battery voltage, current draw, and temperature during operation. Adjust protection thresholds if necessary, but ensure they are within safe limits for your components.

8. User Tips

  • Cooling is Key: Given the high current capabilities, always prioritize good cooling. Consider active cooling solutions (fans) for demanding applications or enclosed spaces.
  • VESC_TOOL Familiarity: Spend time understanding VESC_TOOL. It's a powerful tool for fine-tuning performance and diagnosing issues.
  • Start with Low Settings: When first setting up, especially with new motors, start with conservative current limits and gradually increase them as you test.
  • Check for Firmware Updates: Regularly check the Flipsky website for the latest firmware. Newer firmware often includes bug fixes and performance enhancements.

9. Warranty and Support

Flipsky provides a warranty for consumable electronic products like ESCs and motors. The warranty period is typically 2 months from the 7th day after shipment (shipping date checked by logistic record).

Warranty Conditions:

  • The warranty covers manufacturing defects.
  • Wear and tear caused by normal use is not considered a defect.
  • The warranty does not cover:
    • Purchase through unauthorized channels.
    • Mechanical damage to electronic components or PCB.
    • PCB board repair soldering iron traces (excluding solderable cable bullet connectors).
    • Water damage or external impact damage.
    • Abnormal applications beyond the product specifications.
  • For warranty claims, please contact Flipsky customer support directly. Provide your order number and a detailed description of the issue.

For the most up-to-date warranty policy and support information, please visit the official Flipsky website or contact their customer service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.