ROBORE X5F

Contents

ROBORE X5F Foldable Treadmill User Manual

Model: X5F

1. Important Precautions

Your satisfaction is very important to us. If you encounter any issues such as shipping damage, missing parts, error code, or defects, please contact customer support for assistance. Do not return the product until you have contacted us.

Customer Support E-Mail: service_sports@163.com

Please provide your Order ID and a description of the product problem (attached pictures or videos if necessary).

2. Assembly Instructions

Before assembly, ensure all parts are present and undamaged. Refer to the parts list below.

2.1. List of Fittings

No. Item Quantity
1 Remote Control 1
2 User Manual 1
3 Boost 1
4 Phone holder 1
5 Upper case 1
6 Armrest watch holder 1
7 Running deck 1
8 Washer M8 2
9 Spring washer M8 2
10 Steel ball latch M8*39 2
11 Hexagon socket head cap screw M8*20 2
12 Cross-recessed flat head self-tapping screw ST4*12 3
13 Latex hole plug 2
14 5#Hex key 1
15 6#Hex key 1
16 Knob M8*20 2
17 Knob M8*35 1
18 13-14-15 multi-functional screwdriver 1

2.2. Assembly Steps

  1. STEP1: Check if all parts are complete.

    Verify that all components listed in the 'List of Fittings' are present and undamaged.

  2. STEP2: Install the armrest watch holder.

    Align the tube holes of the armrest holder (6) with the running deck (7) sleeves. Use screws (11) with washers (8) and spring washers (9). Tighten clockwise with hex key (15) to secure. Then fit knob (16) into the front hole as shown.

    Note: This knob is only for positioning to prevent shaking; it's normal if it can't be fully tightened.

    Diagram showing installation of armrest watch holder with labels for screws, washers, and knob.
    Figure 1: Armrest Watch Holder Installation
  3. STEP3: Install the side armrests, upper case, and phone holder.

    Align the side armrest holes with those on the armrest tube, insert steel ball latch (10). Align upper case (5) and phone holder (4) with the lower case holes on the armrest tube. Use 2 screws (12) and multi-function screwdriver (18) to tighten clockwise at marked positions for securing. Then insert the phone holder into the case's corresponding position as shown.

    Diagram showing installation of side armrests, upper case, and phone holder with labels for steel ball latch, screws, and screwdriver.
    Figure 2: Side Armrest and Console Installation
  4. STEP4: Install the hole plugs and adjust the foot pads.

    Take silicone hole plugs (13) and install them into the marked holes on the armrest tubes. Adjust the folding foot pads on the running deck (7) to the unfolded position.

    Diagram showing installation of latex hole plugs and adjustment of foot pads.
    Figure 3: Hole Plug and Foot Pad Adjustment
  5. STEP5: Installation completed.

    Once all previous steps are completed, your treadmill is fully assembled and ready for use.

    Image of the fully assembled treadmill.
    Figure 4: Assembled Treadmill
  6. STEP6: Storage state.

    To store the treadmill, pull out the side armrest latch, loosen armrest tube knob (16) counterclockwise, fold the armrest watch holder down to the diagram position, align its middle hole with the running deck sleeve, and secure with knob (17) (one side only).

    Diagram showing the treadmill in its folded storage state.
    Figure 5: Treadmill in Storage Position

3. Treadmill Operation

  1. Step 1: Insert 2 AAA batteries (not included) into the remote controller.
  2. Step 2: Turn on the power switch of the treadmill.
  3. Step 3: In standby mode, press the "M" key to enter three countdown modes: Time, Distance, and Calorie. During mode selection, the indicator light for the current mode will always be on. Then select one of the modes you want, and press the "+" and "-" keys to increase and decrease the value of the countdown function.
  4. Step 4: After setting the countdown value, press "ON/OFF" to run.
  5. Step 5: When you want to quit the countdown function, press "ON/OFF" again to stop.
Diagram of the remote control with buttons for Speed+, Speed-, Start, Stop, and Pause.
Figure 6: Remote Control Layout

Note: The images are for reference only. The actual remote control may differ due to variations in production batches.

4. Maintenance

4.1. Lubrication

Correct lubrication of the treadmill with silicon oil or Teflon is crucial, especially for normal belts. This lubrication must be performed regularly depending on usage, even before the first use.

To lubricate, lift the running belt and add the oil underneath. After starting the machine, change to the highest speed. The oil will spread from the middle between the running belt and board. Refer to the picture below for guidance.

Diagram showing how to apply lubricant under the treadmill belt, with a lubrication schedule table.
Figure 7: Lubrication Process and Schedule

The treadmill is pre-oiled for instant use. The provided 30ml oil is sufficient for about one year under normal circumstances. If your usage is around 4-7 hours per week, and maintenance is monthly, use approximately 2.5ml of oil each time.

4.2. Running Belt Corrections

1. First, check if the running belt is offsetting to the left or right with a rattling noise.

2. If the above problem occurs, adjust the running belt to the correct position:

Diagram showing how to adjust the running belt if it shifts left or right, with instructions to tighten or loosen screws.
Figure 8: Running Belt Adjustment
  • To correct belt shifting to the Left: Tighten the Left screw (CW) and Loosen the Right screw (CCW).
  • To correct belt shifting to the Right: Loosen the Left screw (CCW) and Tighten the Right screw (CW).

WARNING: Do not put your hand between the roller and running belt, otherwise you will squeeze your fingers.

3. If the running belt slips, use a 5mm wrench to turn both side bolts 1/4 clockwise. Repeat this procedure until the belt is properly tightened.

Caution:

  • Heavy pedaling may cause shutdown (overload protection, not machine failure).
  • Current and voltage overload may cause shutdown.
  • Each person's running habits (how hard the left or right foot tread) may cause the running belt to shift slightly.

5. Troubleshooting

Refer to the table below for common issues and their solutions.

Error Code Error Judgment Solution
E1 Connection Error
  1. The interface of the upper and lower control main connection lines are loose.
  2. The main connection line of the upper and lower control is damaged.
  3. The monitor is damaged.
  4. The controller is damaged.
  1. Reinforce the motor cable.
  2. Replace the main connecting cable of the upper and lower control.
  3. Replace the monitor.
  4. Replace the controller.
E2 Motor Damaged
  1. The motor wire is not connected or loose.
  2. Carbon brush cover for motor is damaged.
  3. The motor is damaged.
  1. Reinforce the motor cable.
  2. Replace the carbon brush cover for motor.
  3. Replace the motor.
E5 Over-current Protection
  1. Excessive load.
  2. The motor or roller is stuck with foreign objects.
  3. The roller is not lubricated enough, and the resistance increases.
  4. The motor is damaged and the resistance increases.
  1. Reduce the load and try not to exceed the rated load.
  2. Remove the stuck object.
  3. Add lubricant.
  4. Replace the motor.
E6 Motor Over-voltage Protection
  1. The user's power grid or voltage is unstable, and the peak voltage is too high.
  2. The wheel diameter value was setting incorrectly.
  3. Controller damaged.
  1. Add an external filter regulator.
  2. Re-set the wheel diameter value so as not to exceed the rated.
  3. Replace the controller.

6. Specifications

Feature Specification
Brand Name ROBORE
Model Number ROBORE X5F
Input Voltage AC 220-240V
Max Power 2.5HP
Speed Range 1-10km/h (0.6-6.3MPH)
Max User Weight 150kg (330lbs)
Running Belt Length 80-120cm (35.8 inches)
Running Belt Width 30-50cm (15.2 inches)
Adjustable Slope Yes (3 levels: 2%, 10%, 14%)
Screen Yes (LED display for Speed, Time, Distance, Calories)
With Speakers No
Bluetooth Connection No
Training Site Waist, Legs, Foot
Heart Rate Test Without
Driving Power Electric
Application Home Use Treadmill
Foldable Yes
Type of Sports Cardio Training
Origin Mainland China
Certification CE
Running Belt Non-slip diamond pattern, with multi-layer shock-absorbing system
Exercise Modes 4-in-1 including Working Mode (0.6-1.5MPH), Walking Mode (0.6-2.5MPH), Jogging Mode (2.5-4.0MPH), Running Mode (4.0-6.3MPH)
Versatility Under-desk usable for office settings, adjustable handles to meet different training needs

6.1. Incline Adjustment

This machine is equipped with two levels of incline adjustment. Please adjust the angle according to your actual needs.

  • Ensure that the support feet are properly adjusted to avoid unnecessary injuries.
  • The height-increasing foot pads should only be used after the support feet have been fully extended. If the rear cover touches the ground, adjust the height of the rear foot pads.
  • Rotate to adjust the height from the ground to prevent the rear guard from scraping against the floor.
Diagram showing the incline adjustment mechanism with high and low settings.
Figure 9: Incline Adjustment Mechanism

7. Warranty and Customer Support

7.1. Warranty

The ROBORE X5F Treadmill provides a 5-year warranty:

  • 5 Year Frame Warranty
  • 1 Year Parts Warranty

7.2. Customer Support

Contact CursorCare for 7/24 response and 100% satisfaction guarantee.

  • 7*24 online California-based customer service team to solve after-sales problems without obstacles.
  • Return Policy: 30-Day Hassle-Free Return and Exchange.
  • Customer Service: California-Based Service Team Providing personalized solutions to ensure 100% customer satisfaction.
  • Exclusive Maintenance Service: We honor our commitment to quality and durability by offering free maintenance tools for orders within 6 months, including lubricants and remote control.

Customer Support E-Mail: service_sports@163.com

A detailed user manual is available in PDF format here.

8. User Tips

  • Maximize Space: Utilize the treadmill's foldable design to easily store it under a sofa or in a compact space when not in use.
  • Vary Your Workout: Experiment with the 3 incline levels (2%, 10%, 14%) to add intensity and target different muscle groups during your cardio sessions.
  • Choose Your Mode: Select from the 4 exercise modes (Working, Walking, Jogging, Running) to match your fitness goals and energy levels for a personalized workout experience.
  • Quiet Operation: Take advantage of the 2.5HP quiet motor (operating at <45db) to exercise without disturbing others, making it ideal for home or office environments.
  • Under-Desk Use: The treadmill is designed to be used under a desk, allowing you to stay active while working or studying.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.