1. Important Safety Information
WARNING: Electric bikes can be dangerous to use. The user assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important to understand your new bicycle. By reading this manual before your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. Your first ride should be taken in a controlled environment, away from cars, obstacles, and other cyclists.
-
1.1 Always Wear A Helmet
Helmets significantly reduce the rate of head injuries. Always wear a helmet that complies with your state laws when riding the E-bike. Check with your local police department for requirements in your community. Make yourself more visible by wearing bright reflective clothing. Keep your reflectors clean and eye protection. Also check your state laws concerning other protective gear that may be required when riding the E-bike.
-
1.2 Know Your E-bike
Your new E-bike incorporates many features and functions. Read this manual thoroughly to understand how those features enhance your riding pleasure and safety.
-
1.3 Ride Within Your Limits
Take it slow until you are familiar with the riding conditions that you encounter. Be especially careful in wet conditions as traction can be greatly reduced and brakes become less effective. Never ride faster than conditions warrant or beyond your riding abilities. Remember that alcohol, drugs, fatigue, and inattention can significantly reduce your ability to make good judgment and safety.
-
1.4 General Safety Notes
All users must read and understand this manual before their first use of the bike. Additional manuals for components used on the bike may also be provided and should be read before use. Ensure that you comprehend all instructions and safety notes/warnings. Ensure the bike fits you properly before your first use. Always wear an approved bicycle helmet. Ensure correct setup and tightening is performed on your bike before first using it and check the setup, tightening, and condition regularly. It is your responsibility to familiarize yourself with the laws and regulations of operating this product in your area. Ensure the handlebar grips are undamaged and properly installed. Do not use this product with standard bike trailers, stands, electric bike racks, or accessories that have not been tested for safety and compatibility. Off-road riding requires close attention, specific skills, and presents variable conditions and hazards. Wear appropriate safety gear and do not ride alone in remote areas. Check local rules and regulations if off-road E-bike riding is allowed. Engaging in extreme riding is extremely dangerous and should be avoided. Bikes and bike parts have strength and integrity limitations, and extreme riding should not be performed. It is recommended not to ride at night if avoidable; ride at night only if necessary.
2. Parts Identification
Familiarize yourself with the various components of your Zefiora V10 Electric Bicycle.
- Bike Frame: The main structure of the bicycle.
- Handlebar: For steering and control.
- Display: Shows operational data.
- LED Headlight: Front illumination.
- Front Fender: Protects from splashes.
- Disc Brake Rotor: Part of the braking system.
- Tire: 20x4.0 inch fat tires.
- Front Fork: Connects the front wheel and handlebars to the frame.
- Pedals: For propulsion.
- Crank: Connects pedals to the chain.
- Chain: Transfers power from pedals to the rear wheel.
- Battery: Power source for the motor and electronics.
- Derailleur: Gear shifting mechanism.
- Bike Motor: Provides electric assistance.
- Rear Fender: Protects from splashes.
- Controller: Manages power to the motor.
- Light: Rear light.
- Seat: Rider's seating area.
- Rear Rack: For carrying cargo.
- Single-speed Button/Downshift: For gear changes.
- Power Button: For turning the display on/off.
- Light Switch: For controlling lights.
- Horn: For signaling.
3. Setup and Assembly
3.1 Unpacking
Carefully unpack the e-bike from its carton. Remove all packaging materials protecting the bike frame and components. Please recycle packaging materials, especially cardboard and foam.
3.2 Front Wheel Installation
- Insert the front wheel into the front fork.
- Next, insert the fork anti-spin hook plate and washer.
- Finally, insert the nut and tighten it securely.
3.3 Kickstand Installation
- Remove the kickstand.
- Position the kickstand on the inside and the screws on the outside.
- Tighten them clockwise using an M6 screwdriver.
3.4 Handlebar Installation
- Loosen the handlebar mounting screws.
- Place the handlebars on.
- Tighten the screws securely.
3.5 Headlight Installation
- First, open the headlight mounting brackets on both sides.
- Install the black spacers.
- Locate the headlight wiring harness and the main wiring harness (with arrow markings).
- Align the arrows and insert them into the harness, then confirm they are securely plugged in.
- Secure the mounting brackets on both sides with screws.
3.6 Front Fender Installation
- Remove the front fender.
- Insert it from back to front.
- Tighten the screws.
3.7 Rear Rack Installation
Adding a rear rack depends on whether you have one or not.
- Locate the taillight, loosen the taillight screws, and remove the taillight.
- Unscrew all four screws on the back.
- Place the rear rack in position, align the holes, and tighten the screws on both sides.
3.8 Taillight and Rear Seat Bag Installation
- Locate the taillight wiring and tie it up with the cable ties that come with the vehicle.
- Place the rear seat bag as shown in the picture, then tighten the fixing screws above the rear fender.
3.9 Adjusting Brake Tightness
Abnormal noise from brakes can be caused by thicker brake pads. This is normal and should return to normal after a few days of riding. If noise persists, follow these steps:
- Prepare tools and locate: Locate the disc brake caliper (metal part holding the brake disc). You will see two vertical screws (usually M6 Allen wrench).
- Loosen the screws: Use an M6 Allen wrench to slightly loosen these two screws (one to one and a half turns) to allow the clamp to move slightly left and right. Do not completely remove them.
- Alignment Position: Gently straighten the wheel with your hand, ensuring it's centered on the frame. Adjust the brake caliper position left and right to align the brake disc exactly in the center of the two brake pads, with even clearance on both sides.
- While adjusting, gently rotate the wheel to check for friction noise. The optimal position is when it rotates smoothly without friction.
- Tighten screws: Keep the caliper in the optimal position and tighten the two loosened screws alternately and in stages. Do not tighten one screw completely at once.
- After tightening, quickly rotate the wheel to confirm no abnormal noises. If slight friction persists, repeat steps 2-3.
4. Operating Instructions
4.1 Operation Meter
The display provides essential information and controls for your e-bike.
- Power On/Off: Press and hold the [Power button] for 2 seconds to turn the device on or off.
- Gear Shift: Press the [+ button] briefly to increase by one gear, and press the [- button] briefly to decrease by one gear.
- ODO/TRIP Data Display Toggle: Briefly press the [Power button] to switch between displaying ODO (Odometer) and TRIP data. The default display is TRIP.
- Implementation Model: Press and hold the [- button] to enter Implementation Model, and release the button to exit.
4.2 Setting Menu Operations
To access general settings, press and hold both the [+ button] and [- button] simultaneously. In the settings menu:
- Switch setting items: Press the [Power button] briefly.
- Adjust setting parameters: Press the [+ button] or [- button] briefly.
- Confirm: Press and hold the [Power button] to save changes and return to the previous level.
- Return to home page: Press and hold the [- button] to exit without saving, or remain inactive for 60 seconds.
SETTING MENU Options:
- SET 1: Wheel Diameter: Adjustable range: 16-29 inches (default: 26 inches). Not adjustable by default.
- SET 2: Speed Limit: Select any value within 1-99 (default: 25 km/h). Not adjustable by default.
- SET 3: Unit: Options: Metric (KM/H) or Imperial (blank) (default: KM/H).
- SET 4: Screen Brightness: Adjustable range: 1-3 levels (default: Level 3).
- SET 5: Auto Sleep Time: Adjustable range: 1-60 minutes (default: 10 minutes).
- SET 6: Single Trip Auto Reset: Set to "y" to clear single trip mileage on startup, or "n" to retain it.
4.3 Gears Operation
Multi-speed bicycles can have internal or derailleur gear systems. Improper shifting can result in the chain jamming or becoming derailed, leading to loss of control or a crash. Always ensure the chain is fully engaged in the desired gear before pedaling hard.
Avoid shifting while standing up on the pedals or under load.
To shift properly, pedal the bicycle with little pressure on the pedals, and move the shifter one gear at a time, ensuring that the chain is fully engaged in that gear before applying more pressure. For bicycles with 3 front chain rings, avoid "Cross Chaining" (chain in smallest cog in rear with inner/smallest chain ring in front, or largest cog in rear with outer/largest chain ring in front). These positions put the chain at extreme angles and can cause premature wear.
5. Battery Usage and Charging
5.1 How to Use the Battery
- Insert the battery key and turn it counterclockwise to turn on the battery switch.
- Remove the battery with both hands.
- Turn on the red switch on the battery power button.
- Press the battery power button briefly to see the battery level.
5.2 Charging Procedure
- Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
- With the battery on or off the bike, place the charger in a flat, secure place.
- Connect the DC output plug from the charger (round barrel connector) to the charging port on the side of the battery.
- Plug the charger input plug (100-240-volt) to the power outlet. Charging should initiate and will be indicated by the LED charge status light on the charger turning red.
- Once fully charged, indicated by the charging indicator light turning green, unplug the charger from the wall outlet first and then remove the charger.
Attention:
- Before charging, ensure the charger light faces upwards.
- Full charge normally takes 3-7 hours.
- Charge the battery in a clean and safe place and do not overcharge.
- Red light means the battery is charging. Green light means the battery is fully charged.
5.3 Battery Charging Information
- Always charge your battery in temperatures between 50 °F - 77 °F (10 °C - 25 °C).
- Ensure the battery and charger are not damaged before initiating charge. If anything unusual occurs, discontinue charging and contact for help.
- The battery can be recharged on or off the bike.
- Do not charge the battery for more than 12 hours at a time or leave a charging battery unattended.
- Always charge in dry, indoor locations away from direct sunlight, dirt, or debris. Charge in a clear area away from potential to trip on charging cords.
- Do not use with the charger inverted, as this can inhibit cooling and reduce charger lifespan.
- The battery should be recharged after each use to ensure full range for the next ride. There is no memory effect.
- Ensure the battery is turned off whenever it is being removed or off the bike. Avoid damaging exposed connector terminals.
- Do not touch the "+" and terminal contacts on the bottom of the battery when the battery is removed from the bike.
6. Maintenance
6.1 Basic Bike Care
To ensure safe riding conditions, properly maintain your e-bike. Follow these guidelines and consult a certified mechanic regularly.
- Properly maintain batteries by keeping them fully charged when between uses of up to two weeks apart.
- Never immerse or submerge the bike or any components in water or liquid as the electrical system may be damaged.
- Periodically check wiring and connectors to ensure there is no damage and they are secure.
- To clean, wipe the frame with a damp cloth. Use a mild non-corrosive detergent mixture if needed. Dry with a clean, dry cloth.
- Store under shelter; avoid leaving the bike in the rain or exposed to corrosive materials. If exposed to rain, dry your bike afterwards and apply anti-rust treatment to the chain and other unpainted steel surfaces.
- Riding on the beach or in coastal areas exposes your bike to salt, which is very corrosive. Wipe down your bike frequently and apply anti-rust treatment to unpainted parts.
- If the hub and bottom bracket bearings have been submerged in water or liquid, they should be re-greased.
- If the paint has become scratched or chipped, use touch-up paint or clear nail polish to prevent rust.
- Regularly clean and lubricate all moving parts, tighten components, and adjust as required.
Your cables, spokes, and chain will stretch after an initial break-in period of 50-100 miles (80-160km), and bolted connections can loosen. Always have a certified, reputable mechanic perform on your E-bike after this initial break-in period. Regular inspections and tune-ups are particularly important for ensuring your bike remains safe and fun to ride.
7. Troubleshooting
7.1 Fault Code Display
When a fault occurs, the red fault indicator on the instrument panel lights up. The instrument interface will flash the fault information as a reminder and display the "Error" prompt.
| No. | Data Status | Meaning | Instrument Display |
|---|---|---|---|
| 1 | 0x21 | Controller Fault | 21 |
| 2 | 0x22 | Throttle Fault | 22 |
| 3 | 0x23 | Motor Phase Loss | 23 |
| 4 | 0x24 | Hall Sensor Fault | 23 |
| 5 | 0x25 | Undervoltage Protection | 25 |
| 6 | 0x26 | Brake Lever Fault | 26 |
| 7 | 0x30 | Communication Fault | 30 |
7.2 Basic Troubleshooting
| Symptom | Possible Causes | Most Common Solutions |
|---|---|---|
| The bike does not work |
|
|
| Irregular acceleration and/or reduced top speed |
|
|
| The motor does not respond when the bike is powered on |
|
|
| Reduced range |
|
|
| The battery will not charge |
|
|
| Wheel or motor makes strange noises |
|
|
If you are still unable to resolve issues after reading the troubleshooting guide, please contact the customer service of the platform you purchased from. They will guide you through the installation and can send you a video if needed. Email: ebikesservice@outlook.com
8. Specifications
| Attribute | Value |
|---|---|
| Model Number | V10 |
| Brand Name | ZEFIORA |
| Certification | CE |
| Rated Passenger Capacity | One Seat |
| Style | Standard Type |
| Max Speed | >50km/h |
| Range per Power | > 60 km |
| Wattage | > 500w (2000W Peak) |
| Power Supply | Lithium battery |
| Voltage | 48V |
| Power Source | Lithium battery |
| Origin | Mainland China |
| Folded | No |
| Motor | Brushless |
| Wheel Size | 20“ |
| Frame Material | Aluminum alloy |
| Vehicle Size | 168 x 69 x 110 cm |
| Packing Size | 138 × 26 × 84 cm |
| Color | Black |
| Net Weight | 37 kg (81.57lb) / 36.5KG (80.47lb) |
| Gross Weight | 46kg (101.41lb) |
| Charger | AC-DC 54.6V 2A, Input: 100-240V AC, Connector: DC 5.5×2.1 mm |
| Brake System | Front and rear disc brake |
| Tire Size | 20x4.0 inch |
8.1 Compliance
Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
9. User Tips
- Adjust for Comfort: The handlebar and seat height are adjustable. Take the time to customize these settings to your height for optimal comfort during rides.
- Night Riding Safety: Utilize the bright headlights, taillights, and brake lights for enhanced visibility and safety when riding at night.
- Monitor Battery Level: Keep an eye on the LCD display to clearly see the battery level. This helps prevent unexpected power loss during your journey.
- Smooth Acceleration: Accelerate gently by twisting the right handlebar for a smooth and controlled ride.
- Pre-Ride Check: Always perform the pre-riding safety checklist (Section 2) before each ride to ensure all components are in good working order.
10. Additional Resources and Support
For further details or if you have any questions, please refer to the official user manual PDF or contact customer service.
- User Manual (PDF): A detailed user manual in PDF format is available for download. View User Manual (PDF)
- Customer Service: For any questions or support, please feel free to contact us. We will reply and solve the problem for you within 24 hours. Email: ebikesservice@outlook.com