LAUNCH X431 CRP123E V3.0 CRP123I V3.0

Contents

LAUNCH X431 CRP123E V3.0 / CRP123I V3.0 OBD2 Scanner User Manual

Advanced Automotive Diagnostic Tool

Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the tool, read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:

  • The tool contains an internal Lithium Polymer battery. To reduce the risk of fire or burns, do not disassemble, crush, pierce, or dispose of the battery in fire or water.
  • This product is not a toy. Do not allow children to play with or near this item.
  • Do not expose the device to rain or wet conditions.
  • Do not place the device on any unstable surface.
  • Never leave the device unattended during charging. The device must be placed on a non-flammable surface.
  • Handle the device with care. If dropped, check for breakage.
  • Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
  • Keep the tool dry, clean, and free of oil, water, or grease. Use a mild detergent on a clean cloth to clean the enclosure.
  • People with pacemakers should consult their physician(s) before use. Electromagnetic fields could cause pacemaker interference.
  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, and other objects away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area. Exhaust gases are poisonous.
  • Chock the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Don't connect or disconnect any test equipment while the ignition is on or the engine is running.

Compliance Information

FCC ID: XUJCRP123XV3

IC: 29886-CRP123XV3

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Innovation, Science and Economic Development Canada's licence-exempt RSSs and part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference; and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

The device for operation in the band 5150-5250MHz is only for indoor use.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) Information

This product meets the government's requirements for exposure to radio waves. The SAR limit is 1.6 W/kg averaged over one gram of tissue. This device was tested for typical body-worn operations 0mm from the body. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user's body, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

1. Overview

1.1 Vehicle Coverage

This diagnostic tool is specially designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN).

A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label, usually located under the hood or by the radiator. If the vehicle is OBD II compliant, the label will designate "OBD II Certified".

LAUNCH X431 CRP123E V3.0 OBD2 Scanner with carrying case
The LAUNCH X431 CRP123E V3.0 OBD2 Scanner and its carrying case.

Government regulations mandate that all OBD II compliant vehicles must have a “common” 16-pin Data Link Connector (DLC).

OBD II Data Link Connector (DLC) pinout diagram
Standard 16-pin OBD II Data Link Connector (DLC) pinout.

Note: Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD II compliant. Only those vehicles with a Vehicle Emissions Control Label stating OBD II Certified are OBD II compliant.

1.2 On-Board Diagnostics (OBD) II

The OBD II system monitors emission control systems and key engine components by performing continuous or periodic tests. It provides information on:

  • Whether the Malfunction Indicator Light (MIL) is commanded “on” or “off”.
  • Which, if any, Diagnostic Trouble Codes (DTCs) are stored.
  • Readiness Monitor status.

1.3 OBD II Definitions

Key terms related to OBD II systems:

  • EOBD: European On-Board Diagnostics, essentially the same as OBD II.
  • Communication Protocols: Allows different systems and sensors to communicate. Five protocols include CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
  • PCM (Powertrain Control Module): The vehicle's "on-board computer" controlling engine management, emissions, and powertrain.
  • DLC (Data Link Connector): The 16-cavity connector for communication between the computer system and the diagnostic tool.
  • MIL (Malfunction Indicator Light): The vehicle's "Check Engine" warning light.
  • DTC (Diagnostic Trouble Code): A code stored in the computer system's memory indicating a fault condition.
  • Freeze Frame Data: Operating conditions stored when a DTC is set.
  • PID (Parameter Identification Data): Data returned by the vehicle's control modules.
  • Monitors: Diagnostic routines in the PCM to test emissions-related components.
  • Enabling Criteria: Vehicle-specific events or conditions required for monitors to run.
  • Trip: A driving cycle where all required enabling criteria for a monitor are met.
  • Drive Cycle: A specific mode of vehicle operation providing conditions to set all readiness monitors.
  • Warm-up Cycle: Vehicle operation after an engine off period where engine temperature rises and reaches a specified level.
  • Fuel Trim (FT): Feedback adjustments to the base fuel schedule.

1.4 Diagnostic Trouble Codes (DTCs)

OBD II DTCs are five-digit alphanumeric codes. They identify a problem area and guide fault diagnosis. Do not replace parts based solely on DTCs without consulting the service manual.

  • The 1st character (B, C, P, or U) identifies the main system (Body, Chassis, Powertrain, or Network).
  • The 2nd character (0-3) identifies the type of code (Generic or Manufacturer-Specific).
  • The 3rd character (0-9, A-F) identifies the specific system or sub-system.
  • The 4th and 5th characters (0-9, A-F) identify the section of the system that is malfunctioning.
DTC Example P0201 diagram showing code structure
Example of a Diagnostic Trouble Code (DTC) structure (P0201).

The DLC is typically a 16-pin connector located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. Location may vary for special designs.

Diagram showing common DLC locations in a car interior
Common locations for the Data Link Connector (DLC) in various vehicle models.

2. Product Description

2.1 Components & Controls

Diagram of LAUNCH CRP123E V3.0 with numbered components
Overview of the LAUNCH CRP123E V3.0 components and controls.
  1. Charging LED: Red indicates charging, Green indicates fully charged.
  2. LCD: Displays test results.
  3. USB Type-C Port: Connects to the charging cable.
  4. DB-15 Diagnostic Connector: Connects to the vehicle's DLC.
  5. Power Button: Turns the tool on or off.
  6. HOME Button: Navigates to the Job Menu screen.
  7. Selection Buttons: Move cursor up/down/left/right for selection and page navigation.
  8. OK Button: Confirms a selection or action.
  9. Return Button: Exits the current program or returns to the previous screen.

2.2 Technical Specifications

FeatureSpecification
Screen5.0 inch 720P LCD touch screen
RAM2 GB
Storage32 GB
OBDII Input Voltage Range9~18V
DC Input Voltage5V
Charging viaDC 5V 2A charging cable or diagnostic cable via vehicle's DLC
Dimensions228 mm x 125 mm x 34 mm
Weight<565g
Operating Temperature0°C to 50°C (32°F to 122°F) (non-charging status)
Storage Temperature-20°C to 70°C (-4°F to 158°F)
Charging Temperature0°C to 40°C (32°F to 104°F)
Operating SystemAndroid 8.1
CPU1.3GHz 4Core
Battery6100mAh
Wireless SupportDual-band WiFi (2.4 & 5.0 GHz)
LanguagesEnglish, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Spanish, Chinese Traditional
Warranty3 years

2.3 Packing List

The following items are typically included in the product package:

  • 1 x Creader Professional 123E/123I handset
  • 1 x OBD II diagnostic cable
  • 1 x DC 5V charging cable
  • 1 x User manual
  • 1 x Carrying bag
Image showing the contents of the product package
Contents of the LAUNCH CRP123E V3.0 product package.

3. Initial Use & Setup

3.1 Charging the Tool

There are two methods to charge the device:

  • Via Charging Cable: Plug one end of the included charging cable into the Type-C port of the tool, and the other end to an external power supply device.
  • Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle's DLC.

The charging LED will illuminate solid green when the battery is fully charged.

3.2 Getting Started

For first-time use, you need to configure some system settings:

  1. Press the power button to turn on the device.
  2. The welcome page will appear. Tap "Start" to proceed.
  3. Choose your desired system language and tap "Next step".
  4. Choose the desired time zone and tap "Next step" to enter the WLAN setup screen.
  5. Slide the WLAN switch to ON. The system will search for available wireless LANs. Select your desired network.
  • If the selected network is open, you can connect directly.
  • If the network is encrypted, enter the security key (network password).
  1. After network connection, tap "Next step" to configure workshop information. Input the required details and tap "Next step".
  2. Read the user agreement, check the box "Agree to all the above terms", and tap "OK" to finish the sign-up process and navigate to the Job Menu.

3.3 Job Menu Overview

The main menu screen includes the following function modules:

  • Local Diagnose: Configures the tool as a professional diagnostic tool.
  • Service Function: Offers coding, reset, relearn, and other service functions.
  • Other Modules: Includes add-on modules to extend functionalities.
  • Upgrade: Updates vehicle diagnostic software and APK.
  • Mall: Allows subscription to extra diagnostic and reset software.
  • Know Your Customer: Assists repair shops with business analysis and customer management.
  • Mine: Checks saved reports, order information, and system settings.
  • Toolbox: Provides practical add-on modules like battery voltage, DTC library, diagnostic record, etc.
  • More: Includes Online support and LAUNCH Academy.

4. Diagnostic Operations

4.1 Connection to Vehicle

  1. Turn the vehicle ignition OFF.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to Section 1.5 for common locations.
  3. Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end to the DB-15 diagnostic connector of the tool. Tighten the captive screws.
  4. Turn the vehicle ignition ON. The engine can be off or running.

Note: A plastic DLC cover may need to be removed. The cable connector is keyed and fits only one way.

4.2 System Diagnostics

This function diagnoses electronic control systems of a single vehicle model. Supported systems and functions vary by product configuration.

4.2.1 Smart Diagnosis (Auto-Detect)

This function quickly accesses electronic control systems by decoding the VIN, eliminating manual menu selection.

  • Set "Automatic detection on connect" to On in Mine -> Settings. After connection and ignition ON, the system enters auto-detect mode.
  • Alternatively, tap Local Diagnose -> AutoDetect if automatic detection is Off.

If VIN is successfully obtained, confirm and tap OK to start diagnosis. A diagnostic report will be generated. If VIN access fails, the tool enters Manual Diagnosis mode.

Auto VIN Detection in progress on the scanner screen
The Auto VIN Detection feature quickly identifies vehicle information.

4.2.2 Manual Diagnosis

If Auto-Detect fails, you can manually input the VIN or select vehicle details:

  1. Input the VIN and tap OK, or select diagnostic software version (e.g., "DEMO").
  2. Select the vehicle model.
  3. Select the desired test item to proceed.

4.2.2.1 Health Report (Quick Test)

This function accesses all electronic control units and generates a detailed report on vehicle health. Tap Health Report on the test item selection screen to start scanning. After scanning, the report will display systems with fault codes in red and normal systems in green.

  • Enter: Select other test functions.
  • Report: Save the diagnostic result as a report (accessible via Mine -> My Report).
  • Clear Code: Clear existing diagnostic trouble codes.
Diagnostic report generation and sharing feature
Generate and share diagnostic health reports via Wi-Fi for easy communication.

4.2.2.2 System Scan

Quickly scans which systems are installed on the vehicle.

4.2.2.3 System Selection

Manually select the test system and function step-by-step. Tap System Selection, then the desired system (e.g., Engine System) to access test functions.

  • Version Information: Reads system mode, vehicle VIN, software, and ECU version.
  • Read Fault Code: Displays detailed information of DTCs.
  • Read Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU.
4-in-1 live data graph display on the scanner
View 4-in-1 live data graphs to analyze transient changes and identify problems.

4.3 OBDII Diagnostics (Full OBD2 Functions)

This option provides a quick way to check for DTCs, isolate MIL causes, check monitor status, verify repairs, and perform emission-related services. The scanner supports all 10 test modes for OBD-II cars:

  1. Reading Codes: Shows detailed descriptions of DTCs.
  2. Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes, and resets monitors.
  3. Data Stream: Reads and displays live ECU/PCM data stream, plots functions graphically, and stores freeze frame data.
  4. I/M Readiness Status: Shows if emissions-related systems are operating properly and ready for inspection/maintenance testing.
  5. Read Live Data Stream: Displays continuous data stream in live graphic (waveform) display.
  6. View Freeze Frame Data: Shows operating conditions when an emission-related fault occurs.
  7. O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results.
  8. On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
  9. Read Vehicle Information: Displays VIN, CID, and CVN.
  10. Component Test: Actuates certain vehicle components via commands from the scanner to test operability.
Full OBD2 functions supported by the scanner
The scanner supports all 10 full OBD2 functions for comprehensive diagnostics.

4.4 4-System Diagnostic Tool

The LAUNCH CRP123E V3.0 / CRP123I V3.0 is designed to quickly scan and troubleshoot problems in four core vehicle systems:

  • Engine System Diagnosis: Read and clear DTCs, view live data stream to pinpoint engine problems and turn off warning lights.
  • ABS System Diagnosis: Access ABS system live data and retrieve fault codes to troubleshoot ABS issues and turn off warning lights.
  • SRS System Diagnosis: Detect electronic parameters in the SRS system to check health status and turn off warning lights.
  • Transmission System Diagnosis: Check the transmission system by reading codes or viewing live data to ensure proper power delivery to wheels and turn off warning lights.
Image illustrating 4-system diagnostic capabilities
The 4-system diagnostic tool quickly scans and troubleshoots problems in Transmission, SRS, ABS, and Engine systems.

4.5 7 Hot Maintenance Services (Reset Functions)

The tool offers 7 special reset functions to help vehicles return to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model.

Image showing 7 special reset functions
The 7 special functions include Oil Reset, Brake Reset, DPF Reset, ABS Bleeding, Battery Matching, Steering Angle Reset, and Electronic Throttle Relearn.
  1. Electronic Parking Brake Reset: Resets brake pads after replacement, or when the brake pad indicator lamp is on, sensor circuit is shorted, or servo motor is replaced.
  2. DPF Reset Service: Clears PM (Particulate Matter) from the DPF filter to stabilize filter performance, performed after sensor/trap replacement or DPF regeneration.
  3. ABS Bleeding: Performs bi-directional tests to check ABS operating conditions, necessary when ABS contains air or components are replaced.
  4. Battery Matching: Resets the monitoring unit of the vehicle battery, clearing low battery fault information and performing battery matching after battery or sensor replacement.
  5. Oil Lamp Reset Service: Resets the Engine Oil Life system after an oil change.
  6. Steering Angle Calibration: Resets the steering angle after replacing the steering angle position sensor, mechanical parts, performing four-wheel alignment, or recovering the car body.
  7. Electronic Throttle Position Reset: Makes initial settings to throttle actuators and returns learned values to default, adjusting air intake.

4.6 History

The tool records every detail of diagnostic sessions. The History function provides direct access to previously tested vehicles, allowing you to resume from the last operation.

5. Maintenance

5.1 Software Updates (Upgrade)

If new software or APK updates are available, a numeric indicator will display on the Upgrade module. Use this option to keep your tool synchronized with the latest version.

  • Tap Upgrade on the Job menu to enter the update center.
  • By default, all diagnostic software is selected. To deselect, tap Unselect.
  • Tap Update to start downloading. It may take several minutes. You can pause (Stop) and resume (Continue) downloads. If network connection fails, tap Retry.
  • Once downloaded, software packages will install automatically.
One-key WiFi update process on the scanner
Perform one-key updates via WiFi for lifetime free software upgrades.

5.2 Cleaning the Device

Keep the tool dry, clean, and free of oil, water, or grease. Use a mild detergent on a clean cloth to clean the enclosure of the device when necessary.

5.3 Diagnostic Software Clear

This item allows you to delete diagnostic software that is not frequently used to free up storage space.

5.4 Firmware Fix

Use this module to upgrade and fix diagnostic firmware. During fixing, do not cut power or switch to other interfaces.

6. Troubleshooting

6.1 DTC Library

This option allows you to retrieve detailed descriptions of specific DTCs from the DTC database. Swipe the screen up/down to alter the value, then press OK to display the DTC definition.

DTC Library interface on the scanner
The DTC Library provides detailed information for diagnostic trouble codes.

6.2 Diagnostic Record

This module stores running parameters or waveform graphs. Tap Diagnostic Record to access and select desired data stream items and jump to the playback page.

6.3 Feedback

This module allows you to send feedback on diagnostic problems for further analysis and troubleshooting.

6.4 FAQ

This module lists frequently asked questions and answers related to the tool.

6.5 Recovery

This option can reset the tool to its default factory setting. Warning: Resetting may cause data loss. Be careful when performing this operation.

6.6 Clean Up

This option allows you to clear cache files and free up storage space.

7. User Tips

  • The CRP123E V3.0 and CRP123I V3.0 models have identical functions; the only difference is a minor external button on the CRP123I. Choose based on your aesthetic preference.
  • This scanner is designed for passenger vehicles only. Do not use it for commercial vehicles, as this may damage the device. Ensure the OBD II interface input voltage is between 9V and 18V.
  • For vehicles that do not support the Auto VIN Scan function, you can manually enter the vehicle's VIN for diagnosis.
  • When clearing fault codes, ensure the vehicle's ignition key is in the ON position with the engine OFF. Clearing DTCs does not fix the underlying problem; proper repairs are necessary to prevent codes from reappearing.
  • Utilize the Wi-Fi sharing feature to easily send diagnostic reports to mechanics or clients, streamlining communication and repair processes.
  • Regularly check for software updates via Wi-Fi to ensure you have the latest features and vehicle coverage.

8. Warranty and Support

8.1 Warranty

This LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.

The warranty does not cover any part that has been abused, altered, used for a purpose other than intended, or used in a manner inconsistent with instructions. The exclusive remedy for any defective automotive meter is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects will be made by LAUNCH. No agent, employee, or representative of LAUNCH has authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.

8.2 Customer Service

If you have any questions on the operation of the unit, contact the seller or LAUNCH TECH Service Center:

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.