Makerbase SERVO28D/35D

Contents

MKS SERVO28D/35D Closed-Loop Stepper Motor Driver User Manual

1. Introduction

The MKS SERVO28D and MKS SERVO35D are advanced closed-loop stepper motor drivers developed by Makerbase. These drivers integrate efficient FOC (Field-Oriented Control) vector algorithms and high-precision encoders to prevent motor step loss through real-time position feedback. They are designed for a wide range of applications including small robotic arms, 3D printers, engraving machines, writers, automation products, and e-sports equipment. The drivers feature both pulse interfaces and optional RS485 or CAN communication interfaces.

MKS SERVO28/35D driver with OLED display
Figure 1: MKS SERVO28/35D driver with an external OLED display and motor connection. Key features include 3000RPM speed, curve acceleration/deceleration, MODBUS support, multi-motor synchronization, limit switch support, and external screen compatibility.

2. Setup and Wiring

Proper connection of power, motor, and control signals is crucial for the correct operation of the MKS SERVO28D/35D driver. Always ensure power is disconnected before making or changing any connections.

2.1 Motor and Power Connections

Connect your stepper motor to the A+, A-, B+, B- terminals. Ensure correct phase wiring. Connect your DC power supply to the V+ and Gnd terminals. The driver supports a wide input voltage range (refer to specifications for exact range).

MKS 28D RS485 V1.0 driver board top and bottom view
Figure 2: Top and bottom view of the MKS 28D RS485 V1.0 driver board. The top side features motor phase connections (A+, A-, B+, B-). The bottom side includes power input (V+, Gnd), control signal inputs (Com, En, Stp, Dir), 5V output, general purpose inputs (G, IN, H), RS485 communication (A, B), and encoder feedback (+R, -R).
MKS 35D RS485 V1.0 driver board top and bottom view
Figure 3: Top and bottom view of the MKS 35D RS485 V1.0 driver board. Similar terminal layout to the 28D RS485 version, supporting larger motors.

2.2 Control Signal Connections (Pulse Interface)

For pulse control, connect your controller's signals to the following terminals:

  • Stp (Step): Pulse input for motor movement.
  • Dir (Direction): Direction input for motor rotation.
  • En (Enable): Motor enable/disable input.
  • Com: Common ground for control signals.

2.3 Communication Interface Connections

Depending on your driver version, connect the communication lines:

  • RS485 Version: Connect RS485 A and B lines to your master device.
  • CAN Version: Connect CAN H and CAN L lines to your CAN bus.
MKS 28D CAN V1.0 driver board top and bottom view
Figure 4: Top and bottom view of the MKS 28D CAN V1.0 driver board. Note the CAN H and CAN L terminals for CAN bus communication.

2.4 External OLED Display Connection

The driver supports an external OLED display and buttons for convenient parameter modification. Connect the OLED display to the dedicated header on the board. This allows for real-time monitoring and adjustment of settings without needing a host computer.

3. Operating Modes and Features

The MKS SERVO28D/35D drivers offer a rich set of features and operating modes:

  • Support for 6 working modes: Pulse interface (open loop, closed loop, FOC mode), Serial interface (open loop, closed loop, FOC mode).
  • MODBUS-RTU communication protocol support (RS485 version).
  • High-performance FOC vector control algorithm with torque, speed, and position three-loop control.
  • Curve acceleration and deceleration for smoother motor start and stop.
  • Single-turn unlimited zeroing function.
  • Multi-turn limit zeroing and left/right limit functions.
  • Direct setting of zero point function.
  • Relative position and absolute position control modes.
  • Support for 1 to 256 arbitrary subdivision steps.
  • Built-in 256-step subdivision interpolation algorithm for super quiet and ultra-low vibration motor operation.
  • Maximum input pulse frequency of 160KHz, supporting speeds up to 3000RPM+.
  • Real-time update of motor angle information (whether motor is enabled or disabled).
  • Onboard industrial-grade high-precision 16384-line magnetic encoder.
  • Onboard 4 high-power MOSFETs, rated 40V/20A.
  • Built-in RS-485 interface with 256 slave addresses and group address support (RS485 version).
  • Built-in CAN interface with 2048 slave addresses and group address support (CAN version).
  • Maximum operating current of 3.0A, with MOSFET continuous operating current of 20A (at 25 °C).
  • Connectivity for an external OLED display screen and buttons for parameter modification, automatic saving, and immediate effect.
  • Built-in stall protection function.
  • Encoder self-calibration function.
  • One-click quick restore to factory settings.
  • Stable high-speed performance, smooth running, no shaking, and emergency stop capability.
  • Provided host computer software (open source) and STM32/Arduino usage routines.

4. Specifications

FeatureSpecification
Product TypeLogic ICs (Closed-Loop Stepper Motor Driver)
OriginMainland China
ConditionNew
Max Input Pulse Frequency160 KHz
Max Speed3000 RPM+
Encoder Resolution16384 lines (magnetic encoder)
MOSFETs4x High-power, 40V/20A
Max Operating Current3.0 A
MOSFET Continuous Current20 A (at 25 °C)
Communication InterfaceRS485 (MODBUS-RTU) or CAN
Subdivision Steps1 to 256 (arbitrary)
Control AlgorithmFOC Vector Control

5. Troubleshooting

  • Motor Not Moving/Stalling:
    • Check all wiring connections (motor phases, power, control signals) for correctness and secure contact.
    • Ensure the power supply voltage and current capacity meet the motor and driver requirements.
    • Verify control signals (Step, Direction, Enable) are correctly applied and within voltage specifications.
    • Check for mechanical obstructions preventing motor movement.
    • Utilize the built-in stall protection feature to diagnose overload conditions.
  • Inaccurate Positioning:
    • Perform encoder self-calibration if available.
    • Ensure the encoder connection is secure and free from interference.
    • Verify that the subdivision settings match your controller's pulse output.
  • Communication Issues (RS485/CAN):
    • Check communication line connections (A/B for RS485, H/L for CAN).
    • Verify baud rates, slave addresses, and communication protocols match between the driver and master device.
    • Ensure proper termination resistors are used on the bus if required.
  • Unusual Noise/Vibration:
    • Check motor mounting for looseness.
    • Verify motor phase wiring.
    • Adjust motor current settings if possible.
    • The built-in 256-step subdivision interpolation algorithm should minimize vibration; if excessive, re-check setup.
  • Driver Overheating:
    • Ensure adequate ventilation around the driver.
    • Verify that the motor current is not set excessively high for the application.
    • Check for short circuits in motor wiring.

6. Maintenance

The MKS SERVO28D/35D drivers are designed for reliable operation with minimal maintenance. Follow these guidelines to ensure longevity:

  • Keep Clean: Regularly clean the driver and surrounding area to prevent dust and debris accumulation, which can hinder heat dissipation. Use a soft, dry brush or compressed air.
  • Environmental Conditions: Operate the driver within its specified temperature and humidity ranges. Avoid exposure to corrosive gases, excessive moisture, or direct sunlight.
  • Connection Integrity: Periodically check all wiring connections for tightness and signs of wear or corrosion. Loose connections can lead to intermittent operation or damage.
  • Firmware Updates: If new firmware versions are released by Makerbase, follow official instructions carefully for updates to potentially improve performance or add features.

7. User Tips

No specific user tips were available from reviews or Q&A for this product at the time of manual creation. General tips for closed-loop stepper drivers include:

  • Start Simple: When first setting up, begin with basic open-loop pulse control to verify motor movement before moving to more complex closed-loop or serial communication modes.
  • Parameter Tuning: Utilize the external OLED display or host computer software to fine-tune PID parameters for optimal performance in your specific application.
  • Documentation: Refer to the provided host computer software (open source) and STM32/Arduino usage routines for example implementations and further guidance.

8. Support

For further assistance, technical support, or detailed documentation, please refer to the following resources:

  • Official Documentation: Consult the latest documentation and resources provided by Makerbase.
  • Software and Routines: Utilize the provided host computer software (open source) and STM32/Arduino usage routines for development and integration.
  • Seller Support: Contact your seller or the manufacturer directly for specific technical inquiries or warranty claims.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.