VDIAGTOOL V210

Contents

VDIAGTOOL V210 Automotive Electrical Circuit Tester User Manual

OBDII/EOBD+CAN VD30 Code Reader

1. General Information

For your own safety and the safety of others, and to prevent damage to the equipment and vehicles, read this manual thoroughly before operating your code reader. The safety messages presented below and throughout this user's manual are reminders to the operator to exercise extreme care when using this device. Always refer to and follow safety messages and test procedures provided by vehicle manufacturer. Read, understand and follow all safety messages and instructions in this manual.

1.1 On-Board Diagnostics (OBDII)

The first generation of On-Board Diagnostics (called OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed. This second generation of On-Board Diagnostic regulations is called “OBDII”. The OBDII system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions. When a problem is detected, the OBDII system turns on a warning lamp (MIL) on the vehicle instrument panel to alert the driver typically by the phrase of “Check Engine” or “Service Engine Soon”.

The system will also store important information about the detected malfunction so that a technician can accurately find and fix the problem. Here below follow three pieces of such valuable information:

  1. Whether the Malfunction Indicator Light (MIL) is commanded “on” or “off”;
  2. Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
  3. Readiness Monitor status.

The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic code readers interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver's side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle's service manual for the location.

Diagram showing the location of the Data Link Connector (DLC) in a car, near the center of the dash.
Figure 1: Typical Data Link Connector (DLC) Location (Near Center of Dash)

2. Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle:

  • Always perform automotive testing in a safe environment. Wear safety eye protection that meets ANSI standards. Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline / chemical / electrical fires nearby. Ignition is on or the engine is running.
  • Keep the scan tool dry, clean, free from oil / water or grease. Use a mild detergent on a clean cloth to clean the outside of the scan tool, when necessary.

3. Tool Description

This section illustrates external features, ports and connectors of the code reader.

Detailed view of the VDIAGTOOL V210 sender and receiver units, highlighting components like the sender switch, mode pilot lamps, electrode clamps, detection probe, extension line, speaker, rotary switch, adjustment knob, measuring button, earphone jack, and battery compartment.
Figure 2: VDIAGTOOL V210 Sender and Receiver Detail Display

3.1 Components Overview

  1. OBDII Cable: Provides communication for vehicle DLC.
  2. LCD Display: Shows menus, test results and operation tips.
  3. Green LED Display: Indicates the engine system is working normally (all monitors on the vehicles are active and performing their diagnostic testing), and no DTCs are found.
  4. Yellow LED Display: Shows the tool finds a possible problem, Pending DTCs exist or / and some of the case, the MIL lamp on the instrument panel is on.
  5. Red LED Display: Indicates there are some problems in one or more of the vehicle's systems. In this case, the MIL lamp on the instrument panel is on.
  6. UP Key: Quick access to the Read Codes function before going to diagnostic menu and moves selection up. When looking up DTC, it is used to change value of selected character.
  7. DOWN Key: Quick access the Clear Codes function before going to diagnostic menu and moves selection down. When looking up DTC, it is used to change value of selected character.
  8. LEFT SCROLL Key: Goes to previous character when looking up DTCs. Scrolls back and forth through codes found and through different screens of data. Also it is used to make selection of PIDs when viewing custom PID list, and to view PID graphs.
  9. RIGHT SCROLL Key: Goes to next character when looking up DTCs. Scrolls back and forth through codes found and through different screens of data. Also it is used to cancel all selections of PIDs when viewing custom PID list.
  10. One Click I/M Readiness Key: Quick checks state emissions readiness and drive cycle verification.
  11. BACK Key: Cancels an action and returns to previous screen or level.
  12. ENTER Key: Confirms an action or movement and moves to next level.
  13. HELP Key: Accesses to the Help function and it is also used to update the code reader when long pressed.
  14. Restart: Restart the code reader.
  15. USB Port: Provides a USB connection between the code reader and PC or laptop.

3.2 Accessories

The VDIAGTOOL V210 comes with the following accessories:

  • 1 x User's Guide (this manual)
  • 1 x USB Cable (for connecting to a computer for updates)

4. Technical Specifications

FeatureSpecification
Display2.8" TFT color display
Working Temperature0 to 60°C (32 to 140°F)
Storage Temperature-20 to 70°C (-4 to 158°F)
Power Supply8-18V vehicle power
Supported ProtocolsJ1850-PWM / J1850-VPW / ISO9141 / KWP2000 (ISO 14230), and CAN (Control Area Network ISO 11898)
Dimensions (L×W×H)147 × 90 × 30mm
Weight0.35kg
Item TypeBattery Testers
Voltage12-24V
Power (W)12V-24V
MaterialPlastic
CertificationsFCC, CE, CCC

5. Setup

5.1 Connecting to Vehicle

Connect the end of the diagnostic cable to the DLC connector in the car.

Image illustrating the V210 Automotive Short/Open Circuit Finder being used by DIYers, in a home garage, and a repair shop, emphasizing its ability to locate short circuits, check open circuits, and trace wires.
Figure 3: V210 Automotive Short/Open Circuit Finder in use across various settings.

5.2 Providing Power to Code Reader

Before using the code reader, make sure to provide power to the code reader. The unit operates on any of the following sources:

  • 12-Volt vehicle power:
    1. Turn the ignition off.
    2. Locate the data link connector (DLC). The DLC is generally located under the dash on the driver side of the vehicle.
    3. Connect the code reader with the DLC.
    4. Switch the ignition key to the ON position.
    5. The code reader automatically boots up.
  • USB connection to personal computer:
    1. Insert the small end of the USB cable to the USB Port at the right side of the code reader and the large end to computer.
    2. Press the power switch of the code reader to power it on.

IMPORTANT: Never try to provide power for the code reader from USB connection when the code reader is communicating with a vehicle.

5.3 Application Overview

When the code reader boots up, the Home screen opens. This screen shows all applications loaded on the unit. Following applications are preloaded into the code reader:

  • OBDII/EOBD: Shows OBDII screens for all 9 generic OBD System tests.
  • Battery: Shows screen that tests and displays voltage of battery of vehicle.
  • DTC Lookup: Shows screens for diagnostic trouble code lookup.
  • Review: Shows screens for access to tested data files.
  • Print Data: Shows screens for access to printing function.
  • Setup: Allows configuration of various settings.

6. Operating Instructions

When the Diagnostics application is selected from the Home screen, the code reader starts to detect the communication protocol automatically. Once the connection has been established, a menu that lists all of the tests available on the identified vehicle displays. Menu options typically include:

  • Read Codes
  • Erase Codes
  • Live Data
  • View Freeze Frame
  • I/M Readiness
  • On-board Monitor Test
  • Component Test
  • Vehicle Information
  • Modules Present
  • Unit of measure
Video: Demonstration of VDIAGTOOL V200 PRO 2-IN-1 Automotive Power Circuit Probe Tester Breaker Finder Tool, showcasing various circuit tests including DC/AC Voltage, Polarity, Resistance, Activating Components, Testing Fuses/Relays/Trailer Lights, and Wire Tracing. It also illustrates powering the device via battery or cigarette lighter, and highlights the 20FT cable with 20FT extension.

6.1 Read Codes

The Read Codes menu lets you read stored codes, pending codes, and permanent codes found in the control unit. Typical menu options include: Stored Codes, Pending Codes, Permanent Codes.

To Read codes from a vehicle:

  1. Press the Read hot key to directly read the codes from home screen. Or scroll with the UP / DOWN key to highlight Read Codes from Diagnostic Menu and Press the ENTER key.
  2. Select Store Codes / Pending Codes / Permanent Codes and press the ENTER key to confirm.
  3. A code list including code number and its description displays.

6.2 Erase Codes

There are two ways to erase codes:

  • Press the Erase hot key to erase codes from home screen.
  • Traditional way: Select Erase Codes from the diagnostic menu.

To erase codes:

  1. Press the Erase hot key to directly erase the codes from the home menu. Or use the UP/DOWN key to highlight Erase Codes from Diagnostic Menu and press the ENTER key.
  2. Follow the on-screen instructions and answer questions about the vehicle being tested to complete the procedure.
  3. Check the codes again. If any codes remain, repeat the Erase Codes steps.

6.3 Live Data

The Live Data menu lets you view, record and playback real time PID data from the electronic control module. Menu options include: View Data, Record Data, Playback Data.

6.3.1 View Data

The View Data function allows real time viewing of the vehicle's electronic control unit's PID data, including sensor data, operation of switches, solenoids and relays. Menu options typically include: Complete Data, Custom Data, Graph Data Set, Unit of measure.

6.3.1.1 Complete Data Set

Complete Data Set displays all supported PIDs of the vehicle being tested.

To view all live PID data:

  1. Use the UP / DOWN key to highlight Live Data from Diagnostic Menu and press the ENTER key.
  2. Select View Data or Complete Data Set from the list and press ENTER key to confirm.
  3. Press the ENTER key to view PID graph if the PID gives a numeric reading.
6.3.1.2 Custom Data List

Custom Data List menu lets you to minimize the number of PIDs on the data list and focus on any suspicious or symptom-specific data parameters.

To create a custom data list:

  1. Select Custom List from the menu and press the ENTER key.
  2. Use the RIGHT key to select or deselect a line or press LEFT key to deselect all if needed. Press the ENTER key to confirm and BACK key to cancel.

6.3.2 Record Data

The Record Data function is used to record PIDs to help diagnose intermittent drivability problems that can't be determined by any other method. Menu options typically include: Complete Data, Custom Data, Graph Data Set, Unit of measure.

NOTE:

There are two types of trigger methods used:

  • Manual Trigger: Triggers recording whenever operators press the ENTER key.
  • DTC Trigger: Automatically triggers recording when a code is detected by vehicle. DTC trigger is not available on all vehicles. Some vehicles need to be driven for a long period of time to store a code after a drivability fault occurs. If DTC trigger is selected to make a recording, there might not be drastic change in the data before and after trigger.

CAUTION: Do not operate the code reader while driving; always have two persons in vehicle when recording - one to drive and the other to operate the code reader.

To record data:

  1. Select Record data from the menu and press the ENTER key.
  2. Refer to View Data to set up Complete Data Set or Customer Data Set to record.
  3. If the recording is to be overwritten, selected Yes; If data is not to be overwritten, pick No to return to select Memory screen and choose another one.
  4. If Manual Trigger is selected, following screen display.
  5. If DTC Trigger is picked, following screen displays.
  6. Press the ENTER key to start recording or wait codes to trigger.

NOTE:

Different vehicles communicate at different speeds and support a different number of PIDs. Therefore, the maximum number of frames that can be recorded varies. The code reader keeps recording data until:

  • The memory is full.
  • The operator presses the BACK key.
  1. After recording, the code reader displays a prompt to Playback.
  2. Select YES to view recorded data; pick NO or press the BACK key to return to Record Data.

6.3.3 Playback Data

The Playback Data is used to playback recorded PID data.

To playback data:

  1. Scroll with the up and down arrow key to select Playback Data from the Menu.
  2. Use the UP/DOWN key to select a memory area that is marked with an asterisk (*) and press the ENTER to confirm.

6.4 View Freeze Frame

Freeze Frame menu displays freeze frame data, a snapshot of critical vehicle operating conditions automatically recorded by the on-board computer at the time of the DTC set. It is a good function to help determine what caused the fault.

To view freeze frame data:

  1. Select View Freeze Frame from the Diagnostic Menu. Details of freeze frame data displays.
  2. Use the UP/DOWN arrow keys to scroll through data to select lines, and LEFT / RIGHT arrow keys to scroll back and forth through different screens of data. If no freeze frame detected, the message "No freeze frame data stored!" is displayed.
  3. Use the BACK key to return to Diagnostic Menu.

6.5 Read I/M Readiness Status Data

I/M Readiness option allows to view a snapshot of the operations for the emission system on OBDII / EOBD vehicles. I/M Readiness is a useful function used to check if all monitors are OK or N/A. The vehicle's computer performs tests on the emission system during normal driving conditions. After a specific amount of drive time (each monitor has specific driving conditions and time required), the computer's monitors decide if the vehicles emission system is working correctly.

When the monitor's status is:

  • OK: vehicle was driven enough to complete the monitor.
  • INC (Incomplete): vehicle was not driven enough to complete the monitor.
  • N/A (Not Applicable): vehicle does not support that monitor.

There are two types of I/M Readiness tests:

  • Since DTCs Cleared: shows status of the monitors since the DTCs were last cleared.
  • This Drive Cycle: shows status of monitors since the start of the current drive cycle.

Below is a list of abbreviations and names of OBD II monitors supported by the code reader:

No.AbbreviationName
1MISMisfire Monitor
2FUELFuel System Monitor
3CCMComprehensive Components Monitor
4CATCatalyst Monitor
5HCATHeated Catalyst Monitor
6EVAPEvaporative System Monitor
7AIRAir Conditioning Refrigerant Monitor
8O2SOxygen Sensor Monitor
9HTROxygen Sensor Heater Monitor
10EGRExhaust Gas Recirculation System Monitor

NOTE:

  • To review I/M Readiness status, make sure that the ignition key is switched to ON with the engine off.
  • Not all monitors are supported by all vehicles.

To retrieve I/M Readiness Status data by one-click I/M readiness key:

  1. Press the One-Click I/M Readiness Key on the keypad.
  2. Colored LED and built-in beeper provide both visual and audible reminders for emission check and DTCs.

When the LED is:

  • Green: Indicates that engine systems are "OK" and working properly (MIL is off). No stored and pending DTCs exist. The vehicle is ready for an Emissions Test.
  • Yellow: The tool finds a possible problem. It indicates either pending DTCs exist or some of the vehicle's emission monitors have not worked properly.
  • Red: Indicates some problems exist with one or more of the vehicle's system, and the vehicle is not ready for an Emissions Test. As well there are DTCs found. The MIL lamp on the vehicle's instrument panel will light steady. The problem that is causing the illumination of Red LED should be fixed before an Emissions Test or driving the vehicle further.

The built-in beeper works with the colored LED simultaneously, as an assistance to reflect the I/M Readiness test results:

  • Green - two long beeps.
  • Yellow - short, long, short beeps.
  • Red - four short beeps.

To retrieve I/M Readiness Status data by typical way:

  1. Scroll with UP/DOWN key to highlight I/M Readiness from Diagnostic Menu and press the ENTER key. If vehicle supports both types of monitors, a screen for monitor type selection displays. Select a monitor type and press the ENTER key.
  2. If the vehicle tested supports both types monitors, following screen displays:
I/M ReadinessStatus
Since DTCs cleared1/2
This driving cycle

Depending on readinesstest, one of these 2 screens will be present. Use the up and down arrow keys to scroll through data. Press the BACK key to exit.

6.6 On-Board Monitor Test

The On-Board Monitor Test function is useful after servicing or after clearing a vehicle ECU's memory. It receives test results for emission-related powertrain components and systems that are not continuously monitored for Non-CAN vehicles. And for CAN vehicles, it receives test data for emission-related powertrain components and systems that are and are not continuously monitored. It is vehicle manufacturer who is responsible for assigning test and component IDs.

NOTE: Test results do not necessarily indicate a faulty component or system.

To request on-board monitor test results:

  1. Use the UP / DOWN key to highlight On-Board Monitor Test from Diagnostic Menu and press the ENTER key.
  2. Depending on the protocol the vehicle used, one of these 2 screens shows:
On-Board Monitor TestStatus
EGR MON. B1S11/25
EGR MON. B1S2
EGR MON. B2S1
EGT MON. B2S2
Catalyst Mon. B1
Catalyst Mon. B2
EGR Monitor Bank1

Or

On-Board Monitor TestStatus
Oxygen Sensor Monitors and Const...1/5
O2 Sensor Heater System Time to...
Exhaust Gas Recirculation System...
Enhanced Evaporative System Monit...
Catalyst Efficiency Monitor
  1. Use the UP / DOWN key to highlight a test group and press the ENTER key to confirm. A screen with details of the selected sensor displays. Use the UP / DOWN arrow keys to scroll through data to select lines, and LEFT / RIGHT arrow keys to scroll back and forth through different screens of data.
  2. Press the BACK key to exit and return.

6.7 Component Test

Component Test allows the code reader to control operation of vehicle components, tests of systems.

NOTE:

  • Some manufacturers do not allow tools to control vehicle systems.
  • The manufacturer sets the criteria to automatically stop test. Refer to appropriate vehicle service manual before using this function.

To perform a component test:

  1. Use the UP / DOWN key to highlight Component Test from Diagnostic Menu and press the ENTER key.
  2. Use the UP / DOWN key to highlight a system or component, press the ENTER key to start test and the code reader displays the message “Command Sent!”.
  3. Press the BACK key to exit and return.

6.8 Request Vehicle Information

Vehicle Information allows to request the vehicle's VIN number, calibration ID(s) which identifies software version in vehicle control module(s), calibration verification numbers (CVN(s)) and in-use performance tracking on model year 2000 and newer OBD II compliant vehicles.

NOTE: Available options will vary depending on the vehicle under test.

To request vehicle information:

  1. Use the UP / DOWN key to highlight Vehicle Info. from Diagnostic Menu and press the ENTER key.
  2. Use the UP / DOWN key to highlight an available option and press the ENTER key. A screen with details of the selected option displays.
  3. Press the BACK key to exit and return.

6.9 Modules Present

The code reader identifies module IDs and communication protocols for OBD2 modules in the vehicle.

To view module IDs and communication types:

  1. Use the UP / DOWN key to highlight Modules Present from Diagnostic Menu and press the ENTER key.
  2. A screen with the module IDs and protocols displays.
  3. Press the BACK key to exit and return.

6.10 Unit of Measure

The code reader identifies module IDs and communication protocols for OBD2 modules in the vehicle.

To view module IDs and communication types:

  1. Use the UP / DOWN key to highlight Modules Present from Diagnostic Menu and press the ENTER key.
  2. A screen with the module IDs and protocols displays.
  3. Press the BACK key to exit and return.

6.11 Battery Test

Selecting Battery option opens a screen that tests and displays voltage of battery.

6.12 DTC Lookup

DTC Lookup menus allows to request DTC definitions stored in the code reader.

To Lookup DTCs:

  1. Use the LEFT / RIGHT key to highlight DTC Lookup from Home Screen and press the ENTER key.
  2. Use the LEFT / RIGHT key to select the desired character, then press the UP / DOWN key to change the digit you want to enter a valid code number. Press the ENTER key to confirm.
  3. A screen with code number and its definition displays. If definition could not be found (SAE or Manufacturer Specific), the code reader displays: “DTC definition not found! Please refer to vehicle service manual!” If a P1xxx, C1xxx, B1xxx or U1xxx code is entered, select a vehicle make to look for DTC definitions. Press the BACK key to exit.

6.13 Review Data

The Playback option leads to screens for review of recorded test results.

To review recorded data:

  1. Use the LEFT / RIGHT key to highlight Review Data from home screen and press the ENTER key.
  2. A screen with a list of test records displays. If no data is recorded, the message "No Data available!" is displayed.
  3. Use the UP / DOWN key to highlight an optional record and press the ENTER key. Details of the test record displays. View and analysis the recorded information then press BACK to exit.

7. Maintenance

7.1 Cleaning the Tool

Keep the scan tool dry, clean, free from oil / water or grease. Use a mild detergent on a clean cloth to clean the outside of the scan tool, when necessary.

7.2 Software Update

To update the code reader, you need the following tools:

  • OBDII / EOBD Code Reader (VDIAGTOOL V210)
  • Update Tool VD30 (software from www.vdiagtool.com)
  • PC or laptop with USB Ports and Internet explorer
  • USB cable

To be able to use the update tool, your PC or laptop must meet the following minimum requirements:

  • Operation System: All Windows systems, Win 98 to Win 10.
  • CPU: Intel PII or better
  • RAM: 64MB or better
  • Hard Disk Space: 30MB or better
  • Display: 800×600 pixel, 16-bit true color display or better
  • Internet Explorer 4.0 or newer

Update Procedure:

  1. Download the update tool VD30 and update files from our website www.vdiagtool.com and save the applications and files in computer disk.
  2. Unzip the update tool file. Follow instructions on computer screen to install the tool and driver.
  3. Double click the VD30 desktop icon to launch the application.
  4. Click Setting and select the language you want to update.
  5. Press and hold HELP key. Do not release the HELP key, then connect the USB cable.
  6. When the tool enters the Update Mode, the application would detect the tool automatically.
  7. Tick the file to update.

8. Troubleshooting

  • "No freeze frame data stored!": This message indicates that no freeze frame data was detected by the tool. This could be due to the vehicle not having stored any freeze frame data for the current fault.
  • "DTC definition not found!": If the tool displays this message, it means the definition for the entered Diagnostic Trouble Code (DTC) could not be found in its database (SAE or Manufacturer Specific). In such cases, refer to your vehicle's service manual for the specific DTC definition.
  • Tool not powering on: Ensure the tool is correctly connected to a 12-18V vehicle power source via the DLC or to a computer via the USB cable. Check all connections for proper seating.
  • Communication errors: If the tool fails to establish communication, verify that the vehicle's ignition is in the ON position and that the DLC connection is secure. Consult your vehicle's manual for DLC location if unsure.
  • Inaccurate readings: Ensure the probe is making good contact with the circuit being tested. Check for any damage to the cables or probe tip.

9. User Tips

  • For intermittent issues, utilize the "Record Data" function to capture PID data over time, which can help in diagnosing problems that don't occur constantly.
  • When tracing wires, ensure the sender is properly connected to the circuit and the receiver's sensitivity is adjusted for optimal detection.
  • Always double-check fuse integrity visually before using the tool to test them, as a blown fuse is often easily identifiable.
  • The long extension cable (20FT cable + 20FT extension) is very useful for reaching components in larger vehicles or when working away from the battery.

10. Warranty and Support

10.1 Limited One Year Warranty

We warrant to our customers that this product will be free from all defects in materials and workmanship for a period of one (1) year from the date of the original purchase, subject to the following terms and conditions:

  1. The sole responsibility of our company under the Warranty is limited to either the repair or, at the option of our company, replacement of the scan tool at no charge with Proof of Purchase. The sales receipt may be used for this purpose.
  2. This warranty does not apply to damages caused by improper use, accident, flood, lightning, or if the product was altered or repaired.
  3. We shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the scan tool. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

10.2 Additional Resources

A copy of the user manual is available in PDF format. For additional language versions (German, Spanish, French), please visit the official VDIAGTOOL website: www.vdiagtool.com. You can also find the user manual PDF directly at: VDIAGTOOL V210 User Manual (PDF).

© 2022 Shenzhen Chuangxinhong Technology Co., Ltd. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.