Safety Information
For your safety and that of others, please read the safety information below before using this product for the first time and pay attention to all highlighted precautions in this manual. The device should be checked periodically and damaged components should never be used.
- Keep away from flammable materials.
- Do not use in rainy, humid, or other unsuitable weather conditions.
- Use a blower brush or clean tissue paper to remove dust and moisture.
- Keep this product out of the reach of children and pets.
- Avoid extended exposure and storage under direct sunlight.
- Before carrying out any maintenance, turn off and unplug the power source. Turn off the power before installing or removing accessories.
- Keep the ventilation holes free of blockages at all times.
- Do not clean with chemical agents or liquids. Do not immerse any part of the flash in liquid.
- Do not attempt to disassemble or repair by yourself.
- Certain parts of the flash will become hot during use and should never be touched with bare hands.
Product Overview
The compact and portable Q120 Outdoor Flash features TTL, M, and Multi modes, along with HSS. The built-in wireless 2.4G Q-system is compatible with Canon, Sony, Nikon, and other cameras. It also supports Bluetooth app control for intuitive operation.

Image: NEEWER Q120 Flash Strobe with included accessories.

Image: NEEWER Q120 Flash Strobe, highlighting 120Ws powerful output and constant color temperature 5600K±100K.
Package Contents
The NEEWER Q120 package includes the following items:
- Flash Unit (x1)
- Carry Bag (x1)
- Battery (x1)
- Charging Cable (x1)
- Handle (x1)
- Diffuser (x1)
Product Illustration
Familiarize yourself with the components of your Q120 flash unit:
- Optical Receiver
- USB-C Port for Firmware Upgrade
- 2.5mm Sync Jack
- Handle Locking Knob
- Umbrella Locking Knob
- Stand Locking Knob
- Optical Lens
- Modeling Lamp
- Umbrella Hole
- Angle Adjustment Knob
Screen Display Elements:
- Flash Mode: M/TTL/MULTI
- Flash Output Power
- Modeling Lamp Status
- Flash Duration
- S1/S2 Mode
- HSS
- Audible Prompt
- Battery Level Indicator
- Mask Function
- Continuous Shooting Mode
- Focal Length
Control Buttons:
- Li-ion Battery
- Short Press: Switches Groups; Long press: Adjusts Channels
- Menu
- Modeling Lamp
- Battery Release Button
- Screen
- Short Press: Focal Length; Long Press: HSS
- Short Press: Switches Modes; Long Press: Wireless On/Off
- Long Press: Powers device On/Off
- Test Flash
- Short Press: Selects Items; Scroll: Adjusts Values
Setup
Mounting the Flash
- Attach the support mount to the underside of the flash and secure it by tightening the locking knob.
- The support mount will drop down over the top of the light stand and is secured using the locking knob.
- Rotate the angle adjustment knob to adjust the angle of the flash.
Battery Installation and Removal
- Installation: Insert the battery into the battery compartment in the direction shown until it clicks into place.
- Removal: Slide the latch in the direction shown to release and remove the battery.
Operating Instructions
Power Management
Battery Features:
- The Li-ion battery supports up to 500 charge-discharge cycles for a long lifespan.
- Built-in protection against overcharging, overdischarging, overcurrent, and short circuits.
Battery Precautions:
- Avoid short-circuiting the positive and negative terminals.
- Do not immerse the battery in water.
- Keep the battery out of reach of children.
- Do not charge the battery for more than 24 hours.
- Store the battery in a cool, dry, and well-ventilated place.
- Keep the battery away from heat sources and open flames.
- Dispose of the battery in accordance with local regulations after it reaches the end of its service life.
- If the battery is not used for more than three months, fully charge it before storage.
Battery Level Indicator:
Ensure the battery is correctly installed. Monitor the battery level on the screen at any time.
| Battery Icon Status | Battery Percentage |
|---|---|
| Full icon | 76%~100% |
| Three bars | 51%~75% |
| Two bars | 26%~50% |
| One bar | 3%~25% |
| Flashing icon | Low Battery/Charging Reminder (continuously flashes, prompting charge/replacement) |
Power On/Off:
- Short Press: Press the power button. The screen displays 'UNLOCK', then scroll 'SET' to the right to power on.
- Long Press: Press the power button to power off.
If not in use for an extended period, turn off the device. The flash features an automatic sleep function.
To access the menu, short press 'MENU', scroll and short press 'SET' to select 'Standby', then scroll 'SET' to choose sleep duration.
When the flash is in sleep mode, short press the power button to wake the device.
TTL Mode
In TTL mode, the camera metering system detects flash light reflected from the subject and automatically adjusts flash output to achieve balanced exposure for both subject and background.

Image: Professional Flash Mode options (TTL, M, Multi).
- Long press 'MODE' to enable wireless mode. Short press 'MODE' until 'TTL' appears on the screen—this sets the flash to TTL mode.
- Note: TTL mode is only available when wireless mode is activated.
1. Flash Exposure Compensation:
- Scroll 'SET' to adjust flash exposure compensation. 0.3 represents 1/3 stop, 0.7 represents 2/3 stop.
2. HSS Mode (High-Speed Sync):
- HSS allows flash use at any shutter speed, especially useful for fill flash in aperture-priority portrait shooting.
- Long press 'Zm' until the HSS symbol appears on screen. HSS requires a compatible wireless transmitter (e.g., Q/QPRO/QZ).
- The master trigger must also have HSS enabled.
- Note: In HSS mode, higher shutter speeds reduce the effective flash range.
- Note: MULTI flashes mode will remain unavailable if HSS is activated.

Image: NEEWER Q120 Flash Strobe in use, demonstrating 1/8000s HSS Sync to freeze motion.
M (Manual) Mode
The flash output power is adjustable from 1/256 to 1/1. To achieve the correct exposure, please use a handheld flash meter to measure the flash output.
- Short press 'MODE' until 'M' appears on screen. The flash mode is now set as M (manual).
- Scroll 'SET' to adjust flash output power.
1. S1/S2 Mode:
- Short press 'MENU' to enter menu, scroll and short press 'SET' to select 'Slave S1/S2', then scroll 'SET' to choose S1 or S2 mode.
- Note: S1/S2 optical triggering is only supported in M (manual) mode.
- Setting the S1 Unit: In M (manual) mode, use the S1 function to set the flash as a slave unit for multiple lighting effects. The flash will trigger in sync with the first burst from the master unit and delivers the same result as a wireless flash trigger.
- Setting the S2 Unit: In M (manual) mode, use the S2 function to set the flash as a slave unit in TTL flash settings. With pre-flash prevention, the flash will trigger in sync with the second burst from the master unit.
2. Mask Function:
- Short press 'MENU' to enter the menu, then scroll and short press 'SET' to select 'Sequence', and scroll 'SET' to choose the desired item.
- Sequence 1, Sequence 2, Sequence 3, and Sequence 4 (sequence can be null) indicate when the flash will trigger.
3. Continuous Shooting Mode:
- Short press 'MENU' to enter the menu, then scroll and short press 'SET' to select 'Continuous Shooting Mode', and scroll 'SET' to enable it.
- Note: Continuous Shooting Mode is supported only in M mode without HSS.
- Note: Flash output power must be set to 1/16 or lower.
4. Consistent Color Temperature:
- Short press 'MENU' to enter the menu. Rotate and short press 'SET' to select 'Consistent Color Temperature', then rotate 'SET' to enable.
- Note: Consistent Color Temperature is available only in M mode.
- If a sound prompt is heard after enabling this function, it means the function is temporarily unavailable due to high flash capacitor energy that may cause overexposure. Fire the flash to discharge, then shoot again.
MULTI (Stroboscopic) Mode
MULTI mode emits a series of rapid flashes that allow you to capture multiple images of a moving subject in a single photo.
- Short press 'MODE'. When 'MULTI' appears on the screen, the flash is set to 'MULTI' mode.
- Scroll 'SET' to adjust flash output power.
- Short press 'SET' to select 'Flash Count', then scroll 'SET' to set number of flashes.
- Short press 'SET' to select 'Frequency', then scroll 'SET' to set flash frequency.
Shutter Speed Calculation:
During stroboscopic flashes, the shutter must remain open until flashing stops. Use the formula below to calculate shutter speed and set it on the camera.
Flash Count / Flash Frequency = Shutter Speed
For example, if the flash count is 10 and the frequency is 5 Hz, shutter speed must be at least 2 seconds.
- To prevent overheating and damage to the flash, do not emit more than 10 consecutive stroboscopic flash sequences. After 10 sequences, allow the flash to cool for at least 15 minutes. If more than 10 consecutive sequences are emitted, the flash may stop automatically to prevent overheating. If this occurs, let it cool for at least 15 minutes.
- "Bulb" is also available in MULTI mode.
- Stroboscopic flashes cannot be set when flash output is 1/1 or 1/2.
- Use of a tripod and remote is recommended.
- Stroboscopic flashes are most effective when shooting highly reflective subjects against a dark background.
Maximum Stroboscopic Flash Count Table:
| Flash Output | Hz (Frequency) | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6-7 | 8-9 | 10 | 11 | 12-14 | 15-19 | 20-50 | 60-100 | |
| 1/4 | 7 | 6 | 5 | 4 | 4 | 3 | 3 | 2 | 2 | 2 | 2 | 2 | 2 |
| 1/8 | 14 | 14 | 12 | 10 | 8 | 6 | 6 | 5 | 5 | 4 | 4 | 4 | 4 |
| 1/16 | 30 | 30 | 30 | 20 | 20 | 20 | 20 | 8 | 8 | 8 | 8 | 8 | 8 |
| 1/32 | 60 | 60 | 60 | 50 | 50 | 40 | 30 | 20 | 20 | 20 | 18 | 16 | 12 |
| 1/64 | 90 | 90 | 90 | 80 | 80 | 70 | 60 | 50 | 40 | 40 | 35 | 30 | 20 |
| 1/128 | 90 | 90 | 90 | 90 | 90 | 90 | 80 | 70 | 70 | 60 | 50 | 40 | 40 |
| 1/256 | 100 | 100 | 100 | 90 | 90 | 90 | 80 | 70 | 70 | 60 | 50 | 40 | 40 |
2.4G Wireless Transmission
The Q120 features a 2.4G wireless Q system to work seamlessly with compatible NEEWER models. When used as a slave unit, it supports Canon E-TTL II, Nikon i-TTL, and Sony TTL. The flash automatically switches according to the master unit, with no manual setting required.
- As a slave unit, the Q120 can be wirelessly controlled by a master unit, including: QPro, QZ, Z1, Z2, Z3, Z760, Z880 series, etc.

Image: Setup showing 2.4G Remote Triggering with a QPRO trigger and App Wireless Control.
1. 2.4G Wireless Setup:
- Long press 'MODE' until the wireless icon appears on the screen.
2. Setting Groups:
- Short press 'GR•CH' to select a group from A/B/C/D/E.
3. Setting Channels:
- Long press 'GR•CH' to enter channel adjustment, then scroll 'SET' to select a channel from 01–32.
4. Setting Wireless IDs:
- Short press the 'MENU' to enter the menu. Scroll and short press 'SET' to select 'Wireless ID', then scroll 'SET' to set an ID from 00–99.
- Note: The master unit and the Q120 must be set to the same channel and ID.
5. Wireless Sync:
When wireless triggering is required, the wireless sync function can quickly match the channel and ID between the master and slave unit.
- Short press 'MENU' to enter the menu, scroll and short press 'SET' to select 'Wireless Sync', then scroll 'SET' and select 'Start'.
- Note: Wireless sync must be enabled on both the master and slave unit. The channel and ID of the master unit will automatically sync to the slave unit for quick wireless pairing.
6. Slave Mode Compatibility:
- Short press 'MENU' to enter the menu, scroll and short press 'SET' to select 'Slave Compatibility'.
- Scroll 'SET' and select 'Off' to use Q system triggers.
- Scroll 'SET' and select 'On' to use X system triggers.
Wireless Flash Shooting Examples:
Using a single slave unit for automatic flash shooting: The master unit (TX) triggers the slave unit (RX). Transmission range is approximately 100m, but may be shorter depending on location, environment, and weather conditions. Perform test flashes and test shots before shooting. Use a master unit with wireless transmission function as the trigger.
Wireless Multi-Flash Shooting: Slave units can be divided into two or three groups to perform TTL automatic flash while adjusting flash ratios. Different flash modes can also be set for each flash group.
Using two slave units for automatic flash shooting: A master unit triggers two slave units (A and B) for broader lighting coverage.
Using three slave units for automatic flash shooting: A master unit triggers three slave units (A, B, and C) for complex lighting setups.
Other Functions
1. Sync Jack Trigger:
- Insert a sync cable or trigger plug into the 2.5mm sync jack to sync the flash.
- Note: When using the sync jack, disable 2.4G wireless mode and S1/S2 modes.
- Note: Sync speed using the sync jack: ≤1/200s.
2. Focal Length Setting:
- Short press 'Zm' to enter focal length adjustment. Scroll 'SET' to adjust between 28-105mm.
3. Delayed Flash:
- Short press 'MENU' to enter the menu. Scroll and short press 'SET' to select 'Delayed Flash', then scroll 'SET' to enable.
- Can be used as a rear-curtain flash.
4. Modeling Lamp:
- Short press the modeling lamp symbol when the value symbol appears. Long press the modeling lamp symbol to enter brightness adjustment, then scroll 'SET' to set brightness between 01–10.
- Short press the modeling lamp symbol when the 'prop' symbol shows. When adjusting flash output power, modeling lamp brightness changes accordingly—higher power, higher brightness.
- Note: Enable 'Brightness Follow' in the menu.
5. APP Control:
- Short press 'MENU' to enter the menu. Scroll and short press 'SET' to select 'Bluetooth', then scroll 'SET' to enable.
- Connect to your phone via Bluetooth. When the Bluetooth icon stops flashing, the connection is successful. Use the NEEWER APP to control the flash.
- For detailed instructions, scan the QR code on the "APP Prompt Card".
Custom Settings
The following table details the custom settings available on your Q120 flash unit:
| Symbol | Function | Setting | Description | Range |
|---|---|---|---|---|
| STANDBY | Auto Sleep | OFF 5min 30min 60min 90min | Disable Automatically sleeps after inactivity | - |
| COLOR | Consistent Color Temperature | ON OFF | ON OFF | M (non-HSS) mode |
| MODEL | Modeling Lamp Mode | On Pause | Modeling lamp stays on Modeling lamp stays paused | - |
| BURST MODE | Continuous Shooting | ON OFF | ON OFF | M≤1/16 |
| Brightness Follow | Modeling lamp brightness follows flash power | ON OFF | ON OFF | M/MULTI |
| Mask | Number of Units | 2 Masks 3 Masks 4 Masks | 2 devices 3 devices 4 devices | Use simultaneously in M mode |
| Sequence | Mask Shooting | OFF Sequence 1 Sequence 2 Sequence 3 Sequence 4 | OFF Trigger response during 1st flash Trigger response during 2nd flash Trigger response during 3rd flash Trigger response during 4th flash | - |
| Delayed Flash | Delayed Shooting | OFF 0.01~30.0s | OFF As Rear-Curtain Flash | M/MULTI |
| WL SYNC | Wireless Sync | START OFF | ON OFF | 2.4G |
| ID | ID Number | OFF 01~99 | OFF Set ID | 2.4G |
| 2.4G | Wireless Transmission | ON OFF | ON OFF | 2.4G |
| S1S2 | Optical Trigger Mode | S1 S2 | S1 S2 | M |
| Sound Prompt | Beep | ON OFF | ON OFF | - |
| Power Adjustment | Increment | +0.1ev +0.3ev | ±0.1ev ±0.3ev | M |
| BLUETOOTH | Bluetooth Mode | ON OFF | ON OFF | - |
| RESET | Restore Factory Settings | OK -- | Restore Factory Settings | - |
| RX COMPAT | Slave Compatibility | ON OFF | ON OFF | 2.4G |
| Language | Display Language | Chinese English | Chinese English | - |
Troubleshooting
Protection Features
To prevent flash head overheating and damage:
- Do not perform more than 60 rapid consecutive flashes at 1/1 power. After 60 flashes, allow the flash to cool for at least 5 minutes.
- When the overheat protection activates, a 'thermometer' symbol will appear on the screen.
Number of Consecutive Flashes Before Overheat Protection Activates:
| Power | Number of Flashes |
|---|---|
| 1/1 | 60 |
| 1/2 | 100 |
| 1/4 | 200 |
| 1/8 | 300 |
| 1/16 | 400 |
| 1/32 | 500 |
| 1/64 | 1000 |
Common Causes and Solutions for 2.4G Wireless Misfires
- External 2.4G signal interference (e.g., wireless base stations, 2.4G Wi-Fi routers, Bluetooth devices, etc.)
→ Adjust the channel on master unit (recommended: +10) to find an interference-free channel, or turn off other 2.4G devices during operation. - Ensure flash is fully recycled and ready to keep up with the speed of continuous shooting (ready indicator on). Check that the flash is not in overheat protection or other abnormal states.
→ Reduce flash power. If using TTL, try switching to M mode. - Transmitter and flash too close (<0.5m)
→ Enable "Short Distance Wireless Mode" on the master unit. For QPro series: set C.Fn-DIST to 0-30m. - Low battery on both master and slave units
→ Replace batteries. Recommended: 1.5V disposable alkaline batteries for the transmitter.
Error Prompts
- E3: High-Voltage Capacitor Overvoltage
- E4: Recycle Error (Over 8s)
- E5: Fan Malfunction
- E6: Temperature Sensor Error (Disconnected/Open Circuit)
Firmware Upgrade
The device supports firmware upgrades via the USB port. The latest firmware will be available on the official website.
- The product does not include a USB cable; please purchase separately. It supports USB-C cables only.
- Firmware upgrades require the "Neewer_Firmware_Update" software. Before upgrading, download and install the software, then select the corresponding firmware file.
- As the product receives firmware updates, please refer to the digital user manual for up-to-date information.
Factory Reset
- Press and hold both 'Zm' and 'MODE' to restore factory settings.
- Alternatively, select 'Reset' in the menu and short-press 'SET'; when 'OK' appears, the device will reset to factory settings.
Specifications
| Feature | Specification |
|---|---|
| Model | Q120 |
| Flash Output Power | 120Ws |
| Flash Duration (t0.1 approx.) | 1/220S-1/23020S |
| Flash Power Range | 1/256~1/1 |
| Delay Flash | 0.01~30S |
| Groups (GR) | A, B, C, D, E |
| Transmission Distance | 100M |
| Modeling Lamp Brightness Levels | 1-10 |
| Modeling Lamp Power | 3W |
| Stroboscopic Flash | Yes (Max Count: 100; Frequency: 100 Hz) |
| Sync Modes | HSS, First-Curtain, Rear-Curtain |
| Flash Duration Display | Yes |
| Recycle Time | 0.01 - 1.5s |
| Triggering Methods | 2.4 GHz / S1 Optical / S2 Optical / 2.5 mm Sync Jack |
| ID | 01~99 |
| CH | 01~32 |
| Power Supply | Lithium Battery |
| Battery Capacity | 7.2V/3000mAH |
| Max Full-Power Flashes | 410-420 |
| Flash Dimensions | 81×81×143mm |
| Weight (with battery) | 671g |
| Frequency Range | 2412.75MHz-2437.75MHz |
| Max Transmit Power | 8.62dBm |
| Compatible Cameras (Wireless Slave) | Nikon, Canon, Sony, FUJIFILM |
| Flash Modes | Wireless Off: M/MULTI Wireless Slave Mode: TTL/M/MULTI |
User Tips
- Godox X2 Trigger Compatibility: The NEEWER Q120 is compatible with Godox 2.4G X SYSTEM triggers (such as the Godox X2) when operating in RX (receiver) mode. Ensure your Godox trigger is updated to the latest firmware for optimal compatibility.
- Firmware Updates: Regularly check the official NEEWER website for firmware updates to ensure the best performance and compatibility with new camera models or accessories.
- Battery Life: To maximize battery lifespan, fully charge the battery before storing the unit for extended periods (over three months).
Warranty & Support
For detailed item guides and documents, including the full user manual in PDF format, please refer to the official resources. You can access the PDF manual here.
For any further assistance or warranty claims, please contact NEEWER customer support through their official channels.