LAUNCH X431 ELITE V3.0

Contents

LAUNCH X431 ELITE V3.0 Bi-Directional Scan Tool

User Manual

Model: X431 ELITE V3.0

Safety Information

WARNING

Study, understand and follow all instructions provided with this product. Read these instructions carefully before installing, operating, servicing or repairing this tool. Keep these instructions in a safe, accessible place.

Caution: To help prevent personal injury,

  • Never use this tool for any application other than for which it was designed.
  • Never alter or modify this tool in any way. Improper operation and / or maintenance of the tool, or modification of the tool could result in serious injury or death.
  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in P (for A/T) or N (for M/T), and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline / chemical / electrical fires nearby.
  • Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
  • Keep this tool dry, clean, free from oil / water or grease. Use a mild detergent on a clean cloth to clean the outside of the tool, when necessary.

FCC Statement

FCCID: XUJCREV20

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio / TV technician for help.

1. Introduction

1.1 Vehicle Coverage

This diagnostic tool is specially designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN). It is required by EPA that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant and this includes all American, Asian and European vehicles.

A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the following:

  1. Vehicle Emissions Control Information (VECI) Label. It is located under the hood or by the radiator of most vehicles. If the vehicle is OBD II compliant, the label will designate OBD II Certified.
Vehicle Emissions Control Information (VECI) Label example
Example of a Vehicle Emissions Control Information (VECI) Label indicating OBD II certification.
  1. Government regulations mandate that all OBD II compliant vehicles must have a "common” 16-pin Data Link Connector (DLC).
16-pin Data Link Connector (DLC) diagram
Diagram of a 16-pin Data Link Connector (DLC).

*Note: Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD II compliant. Only those vehicles with a Vehicle Emissions Control Label stating OBD II Certified are OBD II compliant.

1.2 On-Board Diagnostics (OBD) II

The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions, which will offer three pieces of such valuable information:

  • Whether the Malfunction Indicator Light (MIL) is commanded “on” or “off”;
  • Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
  • Readiness Monitor status.

1.3 OBD II Definitions

The following terms and their definitions are related to OBD II systems. Read and reference this list as needed to aid in the understanding of OBD II systems.

  • EOBD: European On-Board Diagnostics. Essentially the same as OBD II, with the same Data Link Connector and Communication Protocols.
  • Communication Protocols: Allows different systems and sensors in a vehicle to communicate. There are currently five protocols:
    • CAN Bus
    • J1850 VPW
    • ISO 9141-2
    • J1850 PWM
    • ISO 14230 KWP
  • Powertrain Control Module (PCM): The PCM is the OBD II accepted term for the vehicle's "on-board computer." In addition to controlling the engine management and emissions systems, the PCM also participates in controlling the powertrain (transmission) operation. Most PCMs also have the ability to communicate with other computers on the vehicle (ABS, ride control, body, etc.).
  • DLC: Data Link Connector. The 16-cavity connector on the vehicle that allows communication between the computer system and the diagnostic tool.
  • MIL: Malfunction Indicator Light. The vehicle's “Check Engine” warning light that activates when a DTC is stored.
  • DTC: Diagnostic Trouble Code. A code stored in the computer system's memory, which helps to identify the fault condition that is causing the MIL to activate.
  • Freeze Frame Data: Operating conditions that are stored when a DTC is stored.
  • PID: Parameter Identification Data. Data returned by the vehicle's control modules to the diagnostic tool.
  • Monitors: Monitors are “diagnostic routines” programmed into the PCM. The PCM utilizes these programs to run diagnostic tests, and to monitor operation of the vehicle's emissions-related components or systems to ensure they are operating correctly and within the vehicle's manufacturer specifications.
  • Enabling Criteria: Also termed Enabling Conditions. They are the vehicle-specific events or conditions that must occur within the engine before the various monitors will set, or run. Some monitors require the vehicle to follow a prescribed "drive cycle” routine as part of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle. Please refer to the vehicle's factory service manual for specific enabling procedures.
  • Trip: A Trip for a particular Monitor requires that the vehicle is being driven in such a way that all the required “Enabling Criteria” for the Monitor to run and complete its diagnostic testing are met. The “Trip Drive Cycle” for a particular Monitor begins when the ignition key is turned “On.” It is successfully completed when all the "Enabling Criteria” for the Monitor to run and complete its diagnostic testing are met by the time the ignition key is turned “Off.” Since each of the fifteen monitors is designed to run diagnostics and testing on a different part of the engine or emissions system, the “Trip Drive Cycle" needed for each individual Monitor to run and complete varies.
  • Drive Cycle: A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the "ready" condition. The purpose of completing an OBD II drive cycle is to force the vehicle to run its onboard diagnostics. Some form of a drive cycle needs to be performed after DTCs have been erased from the PCM's memory or after the battery has been disconnected. Running through a vehicle's complete drive cycle will "set" the readiness monitors so that future faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. For vehicle specific drive cycle, consult the service manual.
  • Warm-up Cycle: Vehicle operation after an engine off period where engine temperature rises at least 40°F (22°C) from its temperature before starting, and reaches at least 160°F (70°C). The PCM uses warm-up cycles as a counter to automatically erase a specific code and related data from its memory. When no faults related to the original problem are detected within a specified number of warm-up cycles, the code is erased automatically.
  • Fuel Trim (FT): Feedback adjustments to the base fuel schedule. Short-term fuel trim refers to dynamic or instantaneous adjustments. Long-term fuel trim refers to much more gradual adjustments to the fuel calibration schedule than short-term trim adjustments. These long-term adjustments compensate for vehicle differences and gradual changes that occur over time.

1.4 Diagnostic Trouble Codes (DTCs)

OBD II Diagnostic Trouble Codes are codes that are stored by the on-board computer diagnostic system in response to a problem found in the vehicle. These codes identify a particular problem area and are intended to provide you with a guide as to where a fault might be occurring within a vehicle. OBD II Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The second character, a number, 0-3; other three characters, a hex character, 0-9 or A-F provide additional information on where the DTC originated and the operating conditions that caused it to set. Here below is an example to illustrate the structure of the digits:

DTC Example P0202 structure
Example of a Diagnostic Trouble Code (DTC) structure, showing P0202.

The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16-pin connector where diagnostic code readers interface with the vehicle's on-board computer. It is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary.

Refer to the following figure for location examples:

Common DLC locations in vehicles
Common locations for the Data Link Connector (DLC) in various vehicle models.

If the DLC cannot be found, refer to the vehicle's service manual for the location.

2. Setup and Initial Use

2.1 Product Components & Controls

LAUNCH X431 ELITE V3.0 device diagram
Diagram of the LAUNCH X431 ELITE V3.0 device showing its components and controls.
Components and Controls Overview
No.NameDescriptions
1Charging portCharge the tool via data cable (not included).
2DB-15 diagnostic connectorConnect the diagnostic cable.
3Power buttonTurn on/off the tool.
4Touch screenIndicate the test results.
5BACK buttonExit the current program or return to the previous screen.
6HOME buttonNavigate to the home (Job menu) screen.
7Settings buttonQuick dial to the Settings module.

2.2 Accessories Checklist

For detailed accessory items, please consult from the seller. Typically, the package includes:

  • Diagnostic scanner (Main Unit)
  • Diagnostic cable (OBD Diagnostic Cable)
  • User manual
  • Quick start guide
LAUNCH X431 ELITE V3.0 with included accessories
The LAUNCH X431 ELITE V3.0 diagnostic tool with its user manual and diagnostic cables.

2.3 Powering Up The Tool

There are two methods available for powering up the tool:

  • Via Data Cable: Plug one end of data cable (not included) into the charging port of the tool, and the other end to the PC.
  • Via Diagnostic Cable: Insert the diagnostic cable into the vehicle's DLC port. When the tool is powered on, the screen will automatically light up.

2.4 Getting Started

If it is the first time you have used this tool, you need to make some system settings:

  1. Press the [POWER] button to turn on the tool. The screen displays a welcome page. Tap "Start" to go to next step.
  2. Choose the desired system language, and tap "Next step".
  3. Choose the time zone of your current location. The system will automatically configure the time according to the time zone you selected.
  4. The system will automatically search for all available Wi-Fi networks. Choose the Wi-Fi needed.
  5. After the network connection is done, tap "Next step" to configure workshop information. Input the required information, and tap "Next step” to go to next step.

*Note: After you configured it, the system will append it on the report every time a report is successfully generated.

  1. Carefully read all terms and conditions of the user agreement, check "Agree to all the above terms”, and tap "OK" to complete the registration process. It will automatically jump to the Job Menu.

2.5 Connecting to the Vehicle

  1. Turn the vehicle ignition off.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to Section 1.5 for common locations.
  3. Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end to the DB-15 diagnostic connector of the tool, and then tighten the captive screws.
Video demonstrating the unboxing of the LAUNCH X431 ELITE V3.0 and connecting the diagnostic cable to the device.

*Notes:

  • A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the diagnostic cable.
  • The cable connector is keyed and will only fit one way. If you have problems connecting the cable connector to the DLC, rotate the connector 180° and try again.
  1. Turn the ignition on. The engine can be off or running.

Caution: Don't connect or disconnect any test equipment with ignition on or engine running.

3. Operating the Diagnostic Tool

3.1 Job Menu Overview

The Job Menu mainly includes the following function modules:

Job Menu Functions
ModuleDescription
DiagnoseConfigure the tool to operate as a professional diagnostic tool.
OBD IIPresents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.
UpgradeTo update vehicle diagnostic software and APK. (Requires stable network connection)
MallTo subscribe extra vehicle diagnostic software or reset (special function) software that are not included within the tool.
SettingsTo manage data and make some system settings, including Network setup, Workshop information and Brightness etc.

3.2 System Diagnosing

This function is specially designed to diagnose electronic control systems of single vehicle model.

*Notes:

  • The diagnostic software of the vehicle includes all kinds of reset software; users can perform it (select Special function from the diagnostic function list) directly in this module.
  • All software is updated periodically. It is recommended to update and install the latest software version for the best service, functions and experience.
  • Use and update of the diagnostic software pre-installed on the tool is free of charge forever.
  • Use and update of the diagnostic software purchased on the "Mall" is free of charge for one year. If it expires, user needs to renew the subscription.
  • More vehicle coverage can be extended on each model. Just go to “Mall” to subscribe it.

3.2.1 Smart Diagnosis (Auto-Detect)

This function allows you to quickly access the electronic control systems of the vehicle via decoding the VIN, without manual step-by-step menu selection. After connection, turn the ignition key on and the system enters auto-detect mode.

*Notes:

  • Make sure the “Automatic detection on connect” in “Settings” is set as ON.
  • A highly stable and solid network connection is recommended for successful VIN access.

A. Successful VIN Detection: Once the system successfully obtains the VIN (Vehicle Identification Number) information of the currently identified vehicle, it will continue scanning the vehicle systems. After the scanning is complete, a diagnostic report will be automatically generated in the Settings -> Data -> Diagnostic Report.

B. Failed VIN Detection: If the tool failed to access the VIN information, the following screen will appear:

VIN input screen
Screen for manual VIN input when auto-detection fails.

Input the VIN, and tap “OK”, the system will decode the VIN data automatically, and continue the Smart Diagnosis procedure if success. Otherwise the system will enter the Manual Diagnosis mode.

*Notes:

  • The most recognizable location for this number is in the top left corner on the vehicle's dashboard. Other locations include the driver's door or post, and the firewall under the hood.
  • In general, vehicle identification numbers are standardized - all contain 17 characters. VIN characters may be capital letters A through Z and numbers 1 through 0; however, the letters I, O and Q are never used in order to avoid mistakes of misreading. No signs or spaces are allowed in the VIN.

3.2.2 Manual Diagnosis

If the tool cannot obtain or analyze the VIN information, you can also perform Manual Diagnosis. In this mode, you need to execute the menu-driven command and then follow the on-screen instruction to proceed.

*Notes:

  • Before diagnosing, please make sure the corresponding vehicle manufacturer software has been installed on the tool.
  • The diagnostic menu may vary by the vehicle's make, model and year.

Refer to the flowchart illustrated below to diagnose a vehicle manually:

Manual Diagnosis Flowchart
Flowchart for performing a manual diagnosis.

Take DEMO V15.34 as an example to demonstrate how to diagnose a vehicle.

*Note: Illustrations used in this manual are samples, the actual testing screen may vary for each vehicle being tested. The following illustrations are based on the DEMO with basic functions. Vehicle diagnostic software with full systems and full functions can be purchased in the Mall.

  1. Select diagnostic software version: Tap "DEMO” to go to Step 2.
  2. Select vehicle model (varies with different versions): Select the desired vehicle model.
  3. Turn the ignition key to ON: Set the ignition switch to on.
  4. Read vehicle information: After reading the vehicle information, double check if the vehicle information is correct or not. If yes, tap "Yes” to continue.
Vehicle Information screen
Screen displaying vehicle information for confirmation.
  1. Select test item: Select the desired test item to proceed.
Show Menu screen
Show Menu screen with options like Health Report, System Scan, System Selection.

3.2.2.1 Health Report (Quick Test)

This function varies from vehicle to vehicle. It enables you to quickly access all the electronic control units of the vehicle and generate a detailed report about vehicle health.

Tap "Health Report" on the test item selection screen, the system starts scanning the ECUs. Once the scanning is complete, the following screen will appear:

Diagnostic Trouble Code screen
Diagnostic Trouble Code screen showing detected faults.

In the figure above, the tested system with fault code is tagged with a red cross and the system with OK displays with a green tick.

On-Screen Buttons:

  • Report: Tap to save the diagnostic result as a report.
  • Clear Code: Tap to clear the existing diagnostic trouble codes.

3.2.2.2 System Scan

This option allows you to quickly scan which systems are installed on the vehicle.

3.2.2.3 System Selection

This option allows you manually select the test system and function step by step. Tap "System Selection” on the test item selection screen, and tap the desired system (take “Engine” for example) to enter the test function selection screen.

Read Fault Code screen
Screen showing options to Read Fault Code, Clear Fault Code, and Read Data Stream.

*Note: Different vehicle has different diagnostic menus.

A. Read Fault Code

This function displays the detailed information of DTC records retrieved from the vehicle's control system. Tap "Read Fault Code” on the test function selection screen, the screen will display the diagnostic result.

*Note: Retrieving and using DTCs for troubleshooting vehicle operation is only one part of an overall diagnostic strategy. Never replace a part based only on the DTC definition. Each DTC has a set of testing procedures, instructions and flow charts that must be followed to confirm the location of the problem. This information can be found in the vehicle's service manual.

On-Screen Buttons:

  • Help: Tap to view the help information.
  • Code Search: Tap it to search for more information about the current DTC online.
  • Report: To save the current data in text format. All diagnostic reports can be accessed from Settings -> Data -> Diagnostic Report.

B. Clear Fault Code

After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicle's ignition key is in the ON position with the engine off.

*Notes:

  • If you plan to take the vehicle to a Service Center for repair, DO NOT erase the codes from the vehicle's computer. If data is erased, valuable information that might help the technician troubleshoot the problem will also be erased.
  • Clearing DTCs does not fix the problem(s) that caused the code(s) to be set. If proper repairs to correct the problem that caused the code(s) to be set are not made, the code(s) will appear again and the check engine light will illuminate as soon as the problem that cause the DTC to set manifests itself.

C. Read Data Stream

This option retrieves and displays live data and parameters from the vehicle's ECU. Tap "Read Data Stream” on the test function selection screen, the system will display data stream items.

Select Data Stream screen
Screen for selecting data stream items.

On-Screen Buttons:

  • Select All: Tap it to select all items of the current page. To select certain data stream item, just check the box before the item name.
  • Unselect: Tap it to deselect all data stream items.
  • OK: Tap it to confirm and jump to the next step.

After selecting the desired items, tap “OK” to enter the data stream reading page.

Data Stream display screen
Data Stream display screen showing live data values.

*Notes:

  • If the value of the data stream item is out of the range of the standard (reference) value, the whole line will display in red. If it complies with the reference value, it displays in blue (normal mode).
  • The indicator 1/X shown on the bottom of the screen stands for the current page / total page number. Swipe the screen from the right / left to advance /return to the next / previous page.

There are 3 types of display modes available for data viewing, allowing you to view various types of parameters in the most suitable way.

  • Value: Displays the parameters with numbers and lists.
  • Graph: Displays the parameters with wave patterns.
  • Combine: The graphs can be merged for easier comparisons. In this case, different items are marked in different colors.

On-Screen Buttons:

  • Graph Icon: Tap it to view the waveform graph of the current data stream item.
Data Stream waveform graph
Data Stream screen showing a waveform graph of Intake Air Temperature.

Combine: Tap it, a pull-down list of the data stream items appears on the screen. Select the necessary items (Max. 4 items can be selected at the same time) and the screen will display the waveforms corresponding to these items immediately.

Combined Data Stream waveform graph
Combined Data Stream screen showing multiple waveform graphs for comparison.
  • Report: Tap to save the current data as a diagnostic report. All diagnostic reports can be accessed from Settings -> Data -> Diagnostic Report. The tool logs the Date of Report (the date and time at which the report was created) and assigns a unique Report #.
  • Record: Tap to record and save Live Data. Recorded Live Data can serve as valuable information to help you in troubleshooting and diagnosing vehicle problems. All diagnostic records can be access from Settings -> Data -> Diagnostic Record.

D. Special Functions

It offers coding, reset, relearn and more service functions, to help vehicles get back to functional status after repair or replacement. Available tests vary by vehicle manufacturer, model, and year.

Advanced ECU Coding features
Overview of Advanced ECU Coding capabilities including component matching and personalization.
All Reset Services icons
Icons representing various reset services available on the tool.

3.3 OBD II Diagnosis

This function presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.

After the tool is properly connected to the vehicle's DLC, tap “OBD II” in the Job Menu. The tool will automatically start a check of the vehicle's computer to determine which type of communication protocol it is using, then display the Monitor Status. Tap "OK", the following function list appears:

  • 1. Read Codes: This function can identify which section of the emission control system has malfunctioned.
  • 2. Erase Codes: This function erases the codes from the vehicle, after retrieving codes from the vehicle and certain repairs have been carried out. Make sure the vehicle's ignition key is in the ON position with the engine off before the operation.
  • 3. I/M Readiness: This function checks whether or not the various emissions-related systems on the vehicle are operating properly, and are ready for Inspection and Maintenance testing. It can also be used to check the Monitor Run Status, and to confirm if the repair of a car fault has been performed correctly.
  • 4. Data Stream: This function retrieves and displays live data and parameters from the vehicle's ECU.
  • 5. View Freeze Frame: This function takes the snapshot of the operating conditions when an emission-related fault occurs. *Note: If DTCs were erased, Freeze Data may not be stored in vehicle memory depending on vehicle.
  • 6. O2 sensor test: This function retrieves O2 sensor monitor test results of the most recently completed tests from the vehicle's on-board computer.
  • 7. On-board monitor test: This function retrieves test results for emission-related powertrain components and systems that are not continuously monitored. The test's availability is determined by the vehicle manufacturer.
  • 8. EVAP System Test: This function lets you initiate a leak test for the vehicle's EVAP system. Refer to the vehicle's service repair manual to determine the procedures necessary to stop the test.
  • 9. Vehicle Info: This function retrieves a list of information (provided by the vehicle manufacturer) from the vehicle's on-board computer. This information may include:
    • VIN (Vehicle identification Number).
    • CID (Calibration ID).
    • CVN (Calibration Verification Number).

3.4 History

Generally once a vehicle diagnosis is performed, the tool will record the every details of diagnostic session. The History function provides direct access to the previously tested vehicles and users can resume from the last operation, without starting from scratch. Tap "History" on the Diagnose main menu screen, all diagnostic records will be listed on the screen in date sequence.

4. Maintenance and Updates

4.1 Upgrade Diagnostic Software & App

This function allows you to update the diagnostic app and software. All software is updated periodically. It is recommended to update and install the latest software version for the best service, functions and experience.

  1. Use and update of the diagnostic software pre-installed on the tool is free of charge forever. No subscription renewals are required.
  2. Use and update of the diagnostic software purchased in the “Mall” is free of charge for one year. If the free period is due, user needs to renew the subscription. Refer to Section 4.2 for details.

*Note: Make sure the Wi-Fi connection is strong and stable while updating.

Tap "Upgrade” on the Job menu to enter the update center.

Software Upgrade screen
Screen showing available software updates.

By default, all diagnostic software is selected. To deselect certain software, tap “Unselect”, and then check the box next to vehicle model. Tap "Update" to start downloading. It may take several minutes to finish, please be patient. Once download is finished, the software packages will be installed automatically.

4.2 Renew Subscription

When the free period is due, the diagnostic software of the current version will be locked. To unlock it, user needs to renew the subscription. Tap "Upgrade” on the Job menu to enter the update center. All software that expires is displayed in gray. Select the desired diagnostic software, tap “Renew”. Input the 24-digit pin code of Subscription Renewal Card (*need to buy it from the seller or local dealer where you purchased the tool) and then tap "Submit" to finish the renewal. Now the latest diagnostic software is ready for use.

*Note: Please note that a piece of Subscription Renewal Card is only applicable to single software, not to all software installed on this tool.

4.3 Mall

This function allows you to subscribe other vehicle diagnostic software and reset software that are not pre-installed on the tool. All diagnostic software in the mall covers full systems and full functions (excluding online programming and coding etc). Different vehicle software is tagged with different price. Tap "Mall” to open the online software mall. Select the target software and follow the on-screen instructions to finish the transaction.

*Note: The software service belongs to the virtual goods. It becomes immediately effective from the date of the successful transaction and it does not accept the refund. When making payment, please double check the order information. The subscribed software can be free to use and update for one year. After it expires, it will become disabled. In this case, re-subscribe it in the Mall to unlock it.

5. Troubleshooting (FAQ)

Here we list some frequently asked questions and answers related to this tool.

  1. System halts when reading data stream. What is the reason?
    It may be caused by a slackened connector. Please turn this tool off, firmly connect the connector, and switch it on again.
  2. Screen of the tool flashes at engine ignition start.
    Caused by electromagnetic disturbing, and this is normal phenomenon.
  3. There is no response when communicating with on-board computer.
    Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature.
  4. What to do if the system fails to start auto VIN detection?
    Please check the following possible reasons:
    • Whether the tool is properly connected to the vehicle's DLC port.
    • Whether the “Automatic detection on Connect" switch is OFF. If yes, slide it to ON.
  5. Why are there so many fault codes?
    Usually, it's caused by poor connection or fault circuit grounding.
  6. How to upgrade the system?
    1. Switch the tool on and ensure a stable internet connection.
    2. Tap "Settings" on the Job Menu, select "About" -> "Version", and tap "Detect the System Version” to enter the system upgrading page.
    3. Follow the on-screen instructions step by step to finish the process. It may take several minutes depending on the internet speed, please be patient. After upgrade is successfully finished, the tool will automatically restart and enters the Job menu.

6. Specifications

Technical Specifications
FeatureDetail
Screen4" touch screen with a resolution of 480*800
CPU4-core 1.3GHz processor
RAM2GB
ROM (Storage Capacity)16GB (Actual available space: 24.31 GB, remainder occupied by system)
WiFi802.11b/g/n 2.4GHz, 5 GHz
OBD II Input Voltage Range9~18V
Power Up ViaDC 5V data cable (not included) or Diagnostic cable through connection to vehicle's DLC
Working Temperature-10 to 50°C (14 to 122 F°)
Storage Temperature-20 to 70°C (-4 to 158 F°)
Android Version8.1
Battery Capacity3000mAh
Package Dimensions185*108*33.5 (mm)
Main Cable LengthApproximately 117 cm
USB Cable LengthTYPE-C interface, approximately 73.5 cm
Update MethodWi-Fi update
Product Weight<540 g
FCC IDXUJCREV3
Product packaging with specifications
Product packaging showing device specifications.

7. User Tips

  • Regular Updates: Utilize the Wi-Fi update feature to keep your diagnostic software current for the best performance and latest vehicle compatibility. Updates are often quick and seamless.
  • Software Compatibility: While the tool supports specific car brands, be aware that some specialized engine types (e.g., a BMW engine in a Range Rover) might require purchasing additional software packages for full functionality. Always verify compatibility for your specific vehicle model and engine.
  • Offline Functionality: The tool can perform diagnostics without an internet connection once the necessary software is downloaded. Internet is primarily needed for updates and initial setup.
  • Check Reset Functions: If a specific reset function isn't working as expected, confirm its compatibility with your exact car model and year. Not all functions are universally supported across all vehicles, even within a supported brand.

8. Warranty

This warranty is expressly limited to persons who purchase LAUNCH® products for purposes of resale or use in the ordinary course of the buyer's business.

LAUNCH® electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.

This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for an automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects shall be made by LAUNCH in accordance with stipulated procedures.

9. Customer Service and Support

Order Information

Replaceable and optional parts can be ordered directly from your authorized tool supplier. Your order should include the following information:

  • Quantity
  • Part number
  • Item description

Customer Service Contact

If you have any questions on the operation of the unit, please contact the seller, or contact LAUNCH TECH CO., LTD.:

Online Feedback

The LAUNCH Scanner provides a Feedback function to share any problems you encounter in the process of diagnosis. We will make every effort to perform a no-delay problem solving and makes improvements on product quality according to your problems and suggestions, thus offering you a higher quality user experience.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.