LAUNCH X431 ELITE V3.0

Contents

LAUNCH X431 ELITE V3.0 Bi-Directional Scan Tool User Manual

For Audi, Volkswagen, Seat, and Skoda Vehicles

1. Introduction

The LAUNCH X431 ELITE V3.0 is a powerful bi-directional scan tool designed for comprehensive vehicle diagnostics, particularly for Audi, Volkswagen, Seat, and Skoda vehicles. This tool offers full system diagnosis, advanced ECU coding, and a wide range of reset services, making it an essential device for automotive professionals and enthusiasts.

1.1 Vehicle Coverage

This diagnostic tool is specifically designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN). EPA regulations require that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant, including American, Asian, and European vehicles.

A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label located under the hood or by the radiator. If the vehicle is OBD II compliant, the label will designate "OBD II Certified".

Government regulations mandate that all OBD II compliant vehicles must have a "common" 16-pin Data Link Connector (DLC).

1.2 On-Board Diagnostics (OBD) II

The OBD II system monitors emission control systems and key engine components. It provides information on:

  • Whether the Malfunction Indicator Light (MIL) is commanded “on” or “off”.
  • Which, if any, Diagnostic Trouble Codes (DTCs) are stored.
  • Readiness Monitor status.

1.3 OBD II Definitions

Key terms related to OBD II systems:

  • EOBD: European On-Board Diagnostics, similar to OBD II.
  • Communication Protocols: Allows systems to communicate. Currently five protocols: CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
  • Powertrain Control Module (PCM): The vehicle's on-board computer, controlling engine management, emissions, and powertrain operation.
  • DLC (Data Link Connector): The 16-cavity connector for diagnostic tool communication.
  • MIL (Malfunction Indicator Light): The “Check Engine” warning light.
  • DTC (Diagnostic Trouble Code): A code stored in the computer system's memory indicating a fault.
  • Freeze Frame Data: Operating conditions stored when a DTC is set.
  • PID (Parameter Identification Data): Data returned by the vehicle's control modules.
  • Monitors: Diagnostic routines in the PCM to run tests and monitor emissions-related components.
  • Enabling Criteria: Vehicle-specific events or conditions required for monitors to run.
  • Trip: A driving event where all required Enabling Criteria for a monitor are met.
  • Drive Cycle: A specific mode of vehicle operation to set all readiness monitors.
  • Warm-up Cycle: Vehicle operation after engine off where engine temperature rises to a specified level.
  • Fuel Trim (FT): Feedback adjustments to the base fuel schedule (short-term and long-term).

1.4 Diagnostic Trouble Codes (DTCs)

OBD II Diagnostic Trouble Codes are five-digit alphanumeric codes stored by the on-board computer. The first character identifies the control system (P=Powertrain, B=Body, C=Chassis, U=Network). The second character (0-3) and subsequent three characters (0-9 or A-F) provide additional information on the DTC's origin and conditions.

The DLC is typically a 16-pin connector located 12 inches from the center of the instrument panel, under or around the driver's side. For some vehicles, the location may vary. If the DLC cannot be found, refer to the vehicle's service manual.

Diagram showing various possible locations of the Data Link Connector (DLC) in a car interior.

Diagram showing common DLC locations in a vehicle.

2. Setup and Initial Use

2.1 Unboxing and Components

The LAUNCH X431 ELITE V3.0 package includes the main unit, an OBD diagnostic cable, a USB cable, a user manual, and a quick start guide.

Video: Unboxing and initial setup of the LAUNCH X431 ELITE V3.0.

LAUNCH X431 ELITE V3.0 device, OBD cable, and user manual in packaging.

Image: LAUNCH X431 ELITE V3.0 device and included accessories.

2.2 Components & Controls

No.NameDescriptions
1Charging portCharge the tool via data cable (not included).
2DB-15 diagnostic connectorConnect the diagnostic cable.
3Power buttonTurn on/off the tool.
4Touch screenIndicate the test results.
5BACK buttonExit the current program or return to the previous screen.
6HOME buttonNavigate to the home (Job menu) screen.
7Settings buttonQuick dial to the Settings module.

2.3 Powering Up The Tool

There are two methods to power up the tool:

  • Via Data Cable: Plug one end of a data cable (not included) into the charging port of the tool, and the other end to a PC.
  • Via Diagnostic Cable: Insert the diagnostic cable into the vehicle's DLC port. The screen will automatically light up when powered on.

2.4 Getting Started (First Use)

For first-time use, follow these system settings:

  1. Press the [POWER] button to turn on the tool. The screen displays a welcome page. Tap "Start" to proceed.
  2. Choose the desired system language and tap "Next step".
  3. Choose the time zone of your current location. The system will automatically configure the time.
  4. The system will automatically search for available Wi-Fi networks. Choose the required Wi-Fi network.
  5. After network connection, tap "Next step" to configure workshop information. Input the required information and tap "Next step". (Note: This information will be appended to every diagnostic report.)
  6. Carefully read the user agreement, check "Agree to all the above terms", and tap "OK" to complete registration. The tool will then jump to the Job Menu.

2.5 Vehicle Connection

  1. Turn the vehicle ignition off.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC).
  3. Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end into the DB-15 diagnostic connector of the tool. Tighten the captive screws.
  4. Caution: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
  5. Turn the ignition on. The engine can be off or running.

Notes:

  • A plastic DLC cover may need to be removed before plugging in the diagnostic cable.
  • The cable connector is keyed and will only fit one way. If you have problems, rotate the connector 180° and try again.

3. Operating Instructions

3.1 Job Menu Overview

The Job Menu includes the following function modules:

  • Diagnose: Configures the tool for professional diagnostic tasks.
  • OBD II: Quick access to DTCs, MIL status, monitor status, and other emission-related services.
  • Upgrade: Updates diagnostic software and APK. Requires a stable network connection.
  • Mall: Subscribes to extra vehicle diagnostic software or reset functions not pre-installed.
  • Settings: Manages data and system settings like network, workshop information, and brightness.

3.2 System Diagnosing

This function is designed for diagnosing electronic control systems of a single vehicle model.

Notes:

  • The diagnostic software includes various reset functions accessible via "Special function".
  • Software is updated periodically; it is recommended to install the latest version.
  • Use and update of pre-installed diagnostic software is free forever.
  • Use and update of diagnostic software purchased from the "Mall" is free for one year; renewal is required after expiration.
  • More vehicle coverage can be extended via the "Mall".

3.2.1 Smart Diagnosis (Auto-Detect)

This function quickly accesses electronic control systems by decoding the VIN, eliminating manual menu selection. After connecting and turning the ignition on, the system enters auto-detect mode.

Notes:

  • Ensure "Automatic detection on connect" in "Settings" is ON.
  • A stable network connection is recommended for successful VIN access.

If VIN information is successfully obtained, the system scans vehicle systems and generates a diagnostic report in Settings -> Data -> Diagnostic Report.

If VIN information fails, you will be prompted to input the VIN manually or proceed with Manual Diagnosis.

3.2.2 Manual Diagnosis

If auto-detect fails, you can perform Manual Diagnosis by following on-screen instructions. This requires selecting the vehicle manufacturer, model, and scan mode.

Notes:

  • Ensure corresponding vehicle manufacturer software is installed.
  • The diagnostic menu may vary by vehicle make, model, and year.

3.2.3 Health Report (Quick Test)

This function quickly accesses all electronic control units and generates a detailed vehicle health report. Tap "Health Report" on the test item selection screen to start scanning ECUs.

3.2.4 Read Fault Code

Displays detailed information of DTC records. Fault codes are indicated by a red cross, while systems with no faults show a green tick.

On-Screen Buttons:

  • Report: Saves diagnostic results as a report.
  • Clear Code: Clears existing diagnostic trouble codes.

3.2.5 Clear Fault Code

Erases codes from the vehicle after repairs. Ensure the ignition key is in the ON position with the engine off.

Notes:

  • Do NOT erase codes if taking the vehicle to a Service Center, as valuable information may be lost.
  • Clearing DTCs does not fix the problem; proper repairs are necessary to prevent codes from reappearing.

3.2.6 Read Data Stream

Retrieves and displays live data and parameters from the vehicle's ECU. You can select up to 4 items to view their waveforms simultaneously.

On-Screen Buttons:

  • Select All/Unselect: Selects or deselects all data stream items.
  • OK: Confirms selection and proceeds.
  • Graph Icon: Views waveform graph of the current data stream item.
  • Combine: Merges graphs for easier comparison (max 4 items).
  • Report: Saves data as a diagnostic report.
  • Record: Records and saves Live Data for troubleshooting.
Screenshot of the LAUNCH X431 ELITE V3.0 displaying 4-in-1 live data graphing and diagnostic report/feedback options.

Image: 4-in-1 Live Data Graphing and Diagnostic Report/Feedback.

3.2.7 Special Functions

Offers coding, reset, relearn, and other service functions to restore vehicle functionality after repair or replacement. Available tests vary by vehicle manufacturer, model, and year.

Image showing various service functions available on the LAUNCH X431 ELITE V3.0, including Brake Reset, DPF Reset, Oil Reset, Battery Matching, SAS Calibration, Suspension Reset, Seat Calibration, Injector Coding, Throttle Relearn, Sunroof Initialization, ABS Bleeding, Gearbox Adaptation, Window Initialization, FRM Reset, Clutch Adaptation, Idle Speed, DPF Regeneration, and more.

Image: All Service Functions for Audi/VW/Seat/Skoda/Bentley/Bugatti/Lamborghini/VW Business.

3.3 OBD II Diagnosis

This function provides quick access to DTCs, MIL status, monitor status, and other emission-related services. After connecting to the vehicle's DLC, tap “OBD II” in the Job Menu. The tool will automatically detect the communication protocol and display Monitor Status.

Tap "OK" to access the following functions:

  • Read Codes: Identifies the section of the emission control system that has malfunctioned.
  • Erase Codes: Erases codes from the vehicle after repairs.
  • I/M Readiness: Checks if emissions-related systems are operating properly and ready for Inspection and Maintenance testing.
  • Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU.
  • View Freeze Frame: Captures a snapshot of operating conditions when an emission-related fault occurs.
  • O2 sensor test: Retrieves O2 sensor monitor test results.
  • On-board monitor test: Retrieves test results for emission-related powertrain components not continuously monitored.
  • EVAP System Test: Initiates a leak test for the vehicle's EVAP system.
  • Vehicle Info: Retrieves VIN, CID (Calibration ID), and CVN (Calibration Verification Number).

3.4 History

The tool records details of every diagnostic session. The History function provides direct access to previously tested vehicles, allowing users to resume from the last operation without starting from scratch. Diagnostic records are listed in date sequence.

3.5 Settings

The Settings menu allows you to customize various aspects of the tool:

  • Units of measurement: Set to Metric System or English System.
  • Automatic detection on connect: Enable/disable automatic VIN detection upon connection.
  • Brightness: Adjust screen brightness and standby time. (Reducing brightness conserves power.)
  • Sound: Adjust volume and other sound settings.
  • Network: Configure WLAN for tool registration, software updates, and email.
  • Time Zone: Set the device's time zone.
  • Language: Change the system language. Supported languages include English, Traditional Chinese, Spanish, French, German, Italian, Russian, Portuguese, Japanese, Korean, and Polish.
  • Workshop information: Add a personalized tag to diagnostic reports.

4. Maintenance

4.1 General Care

Keep the tool dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the tool when necessary.4.2 Software Updates

The tool's diagnostic app and software are updated periodically. It is recommended to update and install the latest software version for optimal service, functions, and experience.

To update:

  1. Tap "Upgrade" on the Job menu to enter the update center.
  2. By default, all diagnostic software is selected. To deselect, tap "Unselect" and uncheck the box next to the vehicle model.
  3. Tap "Update" to start downloading. This may take several minutes.
  4. Once downloaded, software packages will be installed automatically.

Note: Ensure a strong and stable Wi-Fi connection during updates.

4.3 Renew Subscription

Diagnostic software purchased from the "Mall" is free for one year. After this period, the software will be locked. To unlock it, you need to renew the subscription.

To renew:

  1. Tap "Upgrade" on the Job menu.
  2. Select the expired diagnostic software (displayed in gray) and tap "Renew".
  3. Input the 24-digit pin code of the Subscription Renewal Card (purchased separately) and tap "Submit".

Note: A Subscription Renewal Card is applicable to single software, not all software installed on the tool.

4.4 Data Management

  • Clean Up: Clears cache files and frees up storage space.
  • Diagnostic Record: Stores running parameters and waveform graphs.
  • Diagnostic Report: Stores all diagnostic reports generated.
  • Image: Views and manages all screenshots taken during vehicle diagnostic work.

4.5 Recovery

Use this option to reset the tool to its default factory settings.

Warning: Resetting may cause data loss. Back up important data before performing this operation.

4.6 Firmware Fix

Use this module to upgrade and fix diagnostic firmware. During the fixing process, do not cut power or switch to other interfaces.

5. Troubleshooting (FAQ)

5.1 System halts when reading data stream. What is the reason?

It may be caused by a slackened connector. Turn the tool off, firmly connect the connector, and switch it on again.

5.2 Screen of the tool flashes at engine ignition start.

This is caused by electromagnetic disturbing and is a normal phenomenon.

5.3 There is no response when communicating with on-board computer.

Confirm the proper voltage of the power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is at the proper temperature.

5.4 What to do if the system fails to start auto VIN detection?

Check the following possible reasons:

  • Whether the tool is properly connected to the vehicle's DLC port.
  • Whether the “Automatic detection on Connect" switch is OFF. If yes, slide it to ON.

5.5 Why are there so many fault codes?

Usually, it's caused by poor connection or fault circuit grounding.

5.6 How to upgrade the system?

  1. Switch the tool on and ensure a stable internet connection.
  2. Tap "Settings" on the Job Menu, select "About" -> "Version", and tap "Detect the System Version" to enter the system upgrading page.
  3. Follow the on-screen instructions step by step to finish the process. It may take several minutes depending on the internet speed, please be patient. After the upgrade is successfully finished, the tool will automatically restart and enter the Job menu.

6. Specifications

FeatureSpecification
Model NameX431 ELITE V3.0
Communication InterfaceOBD-II
Software UpdateYes (Lifetime Free Online)
Wireless SupportWifi (2.4 GHz, 5 GHz)
ElectronicYes
Is Batteries IncludedYes (3000mAh)
Special FeaturesWifi
Software Version2026 Version
Hardware Version2026 Version
OriginMainland China
Power (W)5V 1.5A 7.5W
Screen Size3.97 inches, 800*480
CPU1.3 GHz Quad-Core
Android Version8.1
RAM2 GB
Storage Capacity32 GB (Actual available space: 24.31 GB)
OBD II Input Voltage Range9~18V
Working Temperature-10 to 50°C (14 to 122°F)
Storage Temperature-20 to 70°C (-4 to 158°F)
Package Dimensions185*108*33.5 mm
Main Cable LengthApproximately 117 cm
USB Cable LengthTYPE-C interface, approximately 73.5 cm
Product Weight<540 g
Package Weight1.0 kg
Package Length20 cm
Package Width15 cm
Package Height10 cm
Table of device parameters for LAUNCH X431 ELITE V3.0, including screen size, CPU, Android version, battery capacity, and dimensions.

Image: Device Parameters of LAUNCH X431 ELITE V3.0.

7. User Tips

  • Pre-check Compatibility: Before performing advanced functions like ECU Coding or specific reset services, always verify compatibility with your specific vehicle model and year. Contact customer service if unsure.
  • Stable Connection for Updates: Ensure a strong and stable Wi-Fi connection when performing software updates to prevent interruptions and potential data corruption.
  • Backup Data: Regularly save diagnostic reports and recorded live data. If performing a factory reset, back up any critical information first.
  • Understand DTCs: While the tool provides DTCs, remember that these are indicators. Always refer to a vehicle's service manual for detailed testing procedures and flow charts to accurately diagnose and fix problems.
  • Keep Manual Handy: The user manual is integrated into the tool for easy access. Utilize it for quick reference on functions and troubleshooting.

8. Warranty and Support

8.1 Warranty Information

LAUNCH® electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is expressly limited to persons who purchase LAUNCH® products for purposes of resale or use in the ordinary course of the buyer's business.

This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions for use. The exclusive remedy for any automotive meter found to be defective is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects shall be made by LAUNCH in accordance with stipulated procedures.

8.2 Customer Service

If you have any questions on the operation of the unit, please contact the seller or LAUNCH TECH CO., LTD. directly:

8.3 User Manual (PDF)

A detailed user manual in PDF format is available for download and reference. You can access it via the following link: LAUNCH X431 ELITE V3.0 User Manual (PDF)

Copyright © 2023 LAUNCH TECH CO., LTD. All rights reserved.

All information, illustrations, and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.